SavedThe figure shows a horizontal steel bar of thickness h loaded in steady tension and welded to a vertical support. Find the load Fthatwill cause an allowable shear stress, Tallow, in the throats of the welds.b= 3.56 in, d = 2.08 in, h = 5/16 in, and Tallow = 25.5 kpsiThe load Fthat will cause an allowable shear stress in the throats of the welds is7kip.< Prev2 of 2Next> SavedA single-threaded power screw is 25 mm in diameter with a pitch of 5 mm. A vertical load on the screw reaches a maximum of 5kN. The coefficients of friction are 0.05 for the collar and O.15 for the threads. The frictional diameter of the collar is 62 mm. Find theoverall efficiency and the torque to raise and lower the load.The overall efficiency isThe torque to raise the load isThe torque to lower the load is%.kN-mm.kN.mm.ntrencesNext >Prev1 of 2

As per the guidelines we have to solve only first question. So kindly you post the second question…

The figure shows a horizontal steel bar of thickness h loaded in steady tension and welded to a vertical support. Find the load Fthat will cause an allowable shear stress, Tallow, in the throats of the welds. b=3.56 in, d 2.08 in, h = 5/16 in, and Tallow = 25.5 kpsi The load Fthat will cause an allowable shear stress in the throats of the welds is kip.

The figure shows a horizontal steel bar of thickness h loaded in steady tension and welded to a vertical support. Find the load Fthat will cause an allowable shear stress, Tallow, in the throats of the welds. b=3.56 in, d 2.08 in, h = 5/16 in, and Tallow = 25.5 kpsi The load Fthat will cause an allowable shear stress in the throats of the welds is kip.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.10.3P: A flat bar of width b and thickness t has a hole of diameter d drilled through it (see figure). The...

See similar textbooks

Similar questions

: A cylindrical tank with diameter d = 18 in, is subjected to internal gas pressure p = 450 psi. The tank is constructed of steel sections that arc welded circum fereiitially (sec figure). The heads of the tank are hemispherical. The allowable tensile and shear stresses are 8200 psi and 3000 psi, respectively. Also, the allowable tensile stress perpendicular to a weld is 6250 psi. Determine the minimum required thickness /minof (a) the cylindrical part of the tank and (b) the hemispherical heads.
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A tension member is to be constructed of two pieces or plastic glued along plane pq (see figure). For purposes of cutting and gluing, the angle ?? must be between 25 and 45. The allowable stresses on the glued joint in tension and shear are 5.0 MPa and 3.0 MPa, respectively (a) Determine the angle it so that the bar will carry the largest load P. (Assume that the strength of the slued joint controls the design.) (b) Determine the maximum allowable load ?? if the cross-sectional area of the bar is 225
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
A cylindrical tank with hemispherical heads is constructed of steel sections that are welded circumferentially (see figure). The tank diameter is 1.25 m, the wall thickness is 22 mm, and the internal pressure is 1750 kPa, (a) Determine the maximum tensile stress h in the heads of the tank. (b) Determine the maximum tensile stress c in the cylindrical part of the tank. (c) Determine the tensile stress <7W acting perpendicular to the welded joints, (d) Determine the maximum shear stress rtiin the heads of the tank. (e) Determine the maximum shear stress tcin the cylindrical part of the tank
Two boards are joined by gluing along a scarf joint, as shown in the figure. For purposes of cutting and gluing, the angle a between the plane of the joint and the faces of the boards must be between 10° and 40f. Under a tensile load P, the normal stress in the boards is 4.9 MPa. (a) What axe the normal and shear stresses acting on the glued joint if a = 20°? (b) If the allowable shear stress on the joint is 2.25 MPa. what is the largest permissible value of the angle ct? (c) For what angle a with the shear stress on the glued joint be numerically equal to twice the normal stress on the joint?
A steel riser pipe hangs from a drill rig. Individual segments of equal length L = 50 ft are joined to get her using bolted flange plates (see figure part b). There are six bolts at each pipe segment connection. The outer and inner pipe diameters are t2= 14 in. and d1= 13 in.; flange plate thickness tf= 1.5 in.; and boll and washer diameters are db= 1.125 in. and dn. = 1.875 in. Find the number n of permissible segments of pipe based on following allowable stresses. (a) The allowable tensile stress in the pipe is 50 ksi. (b) The allowable tensile stress in a bolt is 120 ksi. Find number of segments n for two cases: pipe hanging in air and pipe hanging in seawater.
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
Two steel rods are welded together (see figure): the seam is oriented at angle ? = 50°. The stresses on the rotated element are sx1=10 ksi, sy1= -12 ksi, and tx1y1= -5 ksi. Find the state of plane stress on the clement if it is rotated clockwise to align the x3 axis with the longitudinal axis of the rods.
Two bars AC and BC of the same material support a vertical load P (see figure). The length L of the horizontal bar is fixed, but the angle fl can be varied by moving support A vertically and changing the length of bar AC to correspond with the new position of support A. The allowable stresses in the bars are the same in tension and compression. When the angle ft is reduced, bar AC becomes shorter, but the cross-sectional areas of both bars increase because the axial forces are larger. The opposite effects occur if the angle 0 is increased. Thus, the weight of the structure (which is proportional to the volume) depends upon the angle ft. Determine the angle ft so that the structure has minimum weight without exceeding the allowable stresses in the bars. Note: The weights of the bars are very small compared to the force P and may be disregarded.
A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN (see figure part a). Use a factor of safety of 1.8 against yielding. (a) If the thickness t of the pipe is one-eighth of its outer diameter, what is the minimum required outer diameter dmin? (b) Repeat part (a) if the tube has a hole of diameter dt 10 drilled through the entire tube, as shown in the figure part b.
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?