Question 9 of 15< >- / 1View PoliciesCurrent Attempt in ProgressThe figure shows data for a portion of the ducting in a ventilation system operating at steady state. The ducts are well insulated andthe pressure is very nearly 1 atm throughout. The volumetric flow rate entering at state 2 is AV2 = 2400 ft3/min. Assume the ideal gasmodel for air with Cp = 0.24 Btu/lb-°R and ignore kinetic and potential energy effects.(AV)1 = 5000 ft³/minAir, Cp = 0.24 Btu/lb°R1T, = 80°Fp=1 atm3 V3 = 400 ft/minT3 = ?2(AV)2T2 = 40°FInsulationft/minDetermine the temperature of the air at the exit, in °F, and the rate of entropy production within the ducts, in Btu/min-°R.II

Given Data (AV)1=5000 ft3/min (AV)2=2400 ft3/min T1=80°F T2=40°F

Answered: The figure shows data for a portion of…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A three-process cycle of an ideal gas, for which cp = 1.064 and cv = 0.804 kilojoules per kilogram per degree Kelvin , is initiated by an isentropic compression 1-2 from 103.4 kiloPascal , 27 degree Celsius to 608.1 kiloPascal. A constant volume process 2-3 and a polytropic process 3-1 with n = 1.2 completes the cycle. Circulation is a steady rate of 0.905 kilogram per second, compute for: Heat Added, QA Net Work done by the cycle, WN Cycle efficiency, e Mean Effective Pressure, PME
As shown in the figure, air with a volumetric flow rate of 17,000 ft3/min enters an air-handling unit at 80oF, 1 atm. The air-handling unit delivers air at 45oF, 1 atm to a duct system with three branches consisting of two 26-in.-diameter ducts and one 50-in. duct. The velocity in each 26-in. duct is 19 ft/s. Assume steady state operation and ideal gas behavior for the air. Determine the mass flow rate of air entering the air-handling unit, in lb/s. The volumetric flow rate in each 26-in. duct, in ft3/min. The velocity in the 50-in. duct, in ft/s.
Steam at 44 bar and a dryness fraction, x = 0.9 is throttled to a pressure of 12 bar. Calculate thedifference in power output in kilowatts between the following two expansion processes:a) Steam at the initial pressure of 44 bar and x = 0.9 at State 1 is expanded in a turbine to State 3 at 0.12 bar.b) Steam at the reduced pressure of 12 bar after throttling at State 2 is expanded in another turbine to State 4 at the same exhaust pressure of 0.12 bar.The mass flow rate of steam is 8 kg/sec in both cases and the expansion in both turbines can be assumed to be reversible and adiabatic. Sketch both expansion processes on the same T-s diagram using the respective initial and final state points as described above.Explain the reason for the difference in power output.Calculate the mass flow rate of steam for the turbine operating at the throttled/reduced pressure to generate the same output as the turbine operating at the pressure before throttling.NOTE: You are required to number the state…
The figure shows data for a portion of the ducting in a ventilation system operating at steady state. The ducts are well insulated and the pressure is very nearly 1 atm throughout. The volumetric flow rate entering at state 2 is AV2 = 4400 ft3/min. Assume the ideal gas model for air with cp = 0.24 Btu/lb·oR and ignore kinetic and potential energy effects.
Steam at 80 bar, 440 °C, enters aturbine operating at steady state with avolumetric flow rate of 236 m 3 /min.Twenty percent of the entering massflow exits through a diameter of 0.25m at 60 bar, 400 °C. The rest exitsthrough a diameter of 1.5 m with apressure of 0.7 bar and a quality of 90%. Determine the velocity at each exitduct, in m/s.
Given that Initial Temperature = 28.5 deg C, Dew Point = 9 deg C, Dry Bulb = 30 deg C, Wet Bulb = 28 deg C, Saturation Pressure = 1.148 kPa Calculate the following:1. v = RaTPa m3/kg 2. ω = 1vkg/m3 where: Pd = saturation pressure at room temperature (from steam table) ω = density of air v = specific volume of dry air T = absolute temperature of room temperature Ra = gas constant of air =0.28706 kJ/kg-K
The following are reasons why we use assumptions to represent reciprocating engines as closed system cycles, EXCEPT: a.All statementds are valid b.Reciprocating engines have equivalent thermal efficiencies as their corresponding cycles c.The shape and behavior of reciprocating engines are too complex d.The working fluid for reciprocating engines is an air-fuel mixture, which could be difficult to model
Use the following conversions where necessary:1hp = 745.7W; ρwater = 1000 kg/m3; ρmercury = 13600 kg/m3; 1 atm = 101.325 kPa; Cp (water) = 4.18 kJ/kg °C; g = 9.81m/s2; For properties of air, use R = 0.287 kJ/kg K; Cv (air) = 0.718 kJ/kg K; Cp (air) =1.005 kJ/kg K air enters a pipe at 25 °C, 100 kPa with a volumetric flow rate of 23 m3/h. On the outer pipe surface is an electrical resistor covered with insulation. With a voltage of 120 V, the resistor draws a current of 4 amps. Assuming the ideal gas model with cp = 1.005 kJ/kg - K for air and ignoring kinetic and potential energy effects, determine i. the mass flow rate of the air, in kg/h ii. the temperature of the air at the exit, in °C
Air passes through a narrow section during horizontal flow. The initial air temperature is 21 [℃], flow rate 91.5 [m / s], pressure 10.56 [Kg / cm2 abs], later flow rate 152 [m/s], pressure 7.05 [Kg/cm2. abs], what is the temperature of the air at the outlet if there is no outside or heat coming in? The average specific heat of air is 7 [kcal / kg mol. ℃] and calculate as an ideal gas.
15 - A fixed volume insulated tank, initially empty, was connected to a distribution line carrying helium gas at a temperature of 135ºC by means of a valve. The valve is opened first and closed when the pressure is the same as the distribution line pressure. What is the final internal energy of helium in the tank? (Internal energy of the warehouse in the final state = Enthalpy of the distribution line). (Cp=5.1926) will be taken. a) 701.0 kJ/kg B) 597.1 kJ/kg NS) 2014.7 kJ/kg D) 2066.7 kJ/kg TO) 2118.6 kJ/kg
Assume 8.72 lb/sec of fluid enter a steady-state, steady-flow system with P1= 92.98 psia, ρ1 = 0.338 lb/ft3, v1 = 91.21 fps, u1 = 794.36 BTU/lb, and leave with P2 = 28.14 psia, ρ2 = 0.181 lb/ft3, v2 = 409.94 fps, and u2 = 750.5 BTU/lb. During the passage through the open system, each pund rejects 13.2 BTU of heat. Determine the work in hp.
8Air enters the diffuser of a ramjet engine (schematic shown below) at 6 lbf/in.2, 420°R, with a velocity of 1800 ft/s, and decelerates essentially to zero velocity. After combustion, the gases reach a temperature of 2000°R before being discharged through the nozzle at 6 lbf/in.2 On the basis of an air-standard analysis, determine:(a) the pressure at the diffuser exit, in lbf/in.2(b) the velocity at the nozzle exit, in ft/s.Neglect kinetic energy except at the diffuser inlet and the nozzle exit. Assume combustion occurs at constant pressure and flow through the diffuser and nozzle is isentropic.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS