The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple by an equivalent couple M and resultant R at A. The couple is positive if counterclockwise, negative if clockwise. 2.20 KN 0.46 m 1.71 m A Answers: M- i R-(& 500 N-m 5D kN-m 0.13 m 0.13 m 1.12 KN 1) kN

The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple by an equivalent couple M and resultant R at A. The couple is positive if counterclockwise, negative if clockwise. 2.20 KN 0.46 m 1.71 m A Answers: M- i R-(& 500 N-m 5D kN-m 0.13 m 0.13 m 1.12 KN 1) kN

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.94RP: The properties of the unequal angle section are Ix=80.9in.4,Iy=38.8in.4, and Iu=21.3in.4. Determine...

See similar textbooks

Similar questions

Determine the magnitude of the vertical force C, for the simply supported beam, where w = 11 kips/ft, L1 = 9 ft and L2 = 5 ft.
Determine the magnitude of the vertical force Ay for the simply supported beam, where w = 8 kips/ft, M = 305 kip-ft, L1 = 11 ft, L2 = 3 ft, and L3 = 6 ft.
THE TWO MAIN CABLES OF THE AKASHI KAIYO SUSPENSIONBRIDGE IN JAPAN HAVE A SPAN L= 1990m AND A SAG H = 233m.THE LOADING ON EACH CABLE ISWO = 444.7 KN/m (withouttraffic) ALONG THE HORIZONTAL. DETERMINE THE CORRESPONDING MAXIMUM FORCE IN ONE OF THE CABLES. Give: Given, FBD, AND solution
The two timber beams loaded as shown are connected by a roller support at point C and supported by hinge at D and A. Beam AC is supported by steel rod 3m from point A. Determine the vertical displacement at point C. Show all the necessary solution.
Determine the magnitude of the vertical force Cy for the simply supported beam, where w = 8 kips/ft, M = 270 kip-ft, L1 = 12 ft, L2 = 3 ft, and L3 = 7 ft.
Solve Prob. 3.43 for the position corresponding to x = 4 in. The 20-in. tube AB can slide along a horizontal rod. The ends A and B of the tube are connected by elastic cords to the fixed point C. For the position corresponding to x = 11 in., determine the angle formed by the two cords, (a) using Eq. (3.30), (b) applying the law of cosines to triangle ABC.
The two bars, pinned together at B, are supported by a frictionless surface at A and built-in support at C. Determine the internal moment acting on section 1. a 162n.m b 126n.m c 261n.m d 612n.m
Draw the shear force and moment diagram between AB, assuming the earth pressure to the foundation AB as uniformly distributed.
The brace and drill bit is used to drill a hole at O. If the drill bit jams when the brace is subjected to the forces shown determine the resultant internal loadings acting on the cross-section of the drill bit at A.
The structure shown consists of a single member ABCDE with a pin support at A and a roller support at E. Points B and D are at the midpoints of their respective segments. Determine the internal normal force acting on H which are located immediately to the right of B. Take N = 2 kN, O = 5 kN, and P = 5 kN.
The uniform 10 kg rod AB is supported by a ball and socket joint at A and by the cord CG that is attached to the midpoint G of the rod. Knowing that the rod leans against a frictionless vertical wall at B and that the tension in the cord CG, TCG=52.1 N, determine the following, Which of the following best approximates the moment of the tension in cord CG, TCG about the x axis? Choices: -11.03 N-m5.52 N-m29.4 N-m-7.36 N-m
A 200-lb man starts at end A of the wooden plank and walks toward end B. If the plank will fail when the maximum bending stress is 6000 psi, find the farthest distance x that the man can walk safely.