The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple by an equivalent couple M and resultant R at A. The couple is positive if counterclockwise, negative if clockwise. 2.03 kN 0.41 m 1.82 m 76° 10.18 m A 0.18 m 650 N-m L--x 8 1.07 kN Answers: M = i kN-m R = ( i i+ i j) kN

The flanged steel cantilever beam with riveted bracket is subjected to the couple and two forces shown, and their effect on the design of the attachment at A must be determined. Replace the two forces and couple by an equivalent couple M and resultant R at A. The couple is positive if counterclockwise, negative if clockwise. 2.03 kN 0.41 m 1.82 m 76° 10.18 m A 0.18 m 650 N-m L--x 8 1.07 kN Answers: M = i kN-m R = ( i i+ i j) kN

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter9: Statics And Torque

Section: Chapter Questions

Problem 13PE: Suppose a 900-kg car is on the bridge in Figure 9.34 with its center of mass halfway between the...

See similar textbooks

Similar questions

In order to get his car out of the mud, a man ties one end of a rope to the front bumper and the other end to a tee 15 m away as shown below. He then pulls on the center of the rope with a force of 400 N, which causes its center to be displaced 0.30 m, as shown. What is the force of the rope on the car?
A 15.0-in uniform ladder weighing 500 N rests against frictionless wall. The ladder makes a 60.0 angle ESI with the horizontal, (a) Find the horizontal and vertical forces the ground exerts on the base of the ladder when an 800-N firelighter has climbed 4.00 m along the ladder from the bottom, (b) If the ladder is just on the verge of slipping when the firefighter is 9.00 m from the bottom, what is the coefficient of static friction between ladder and ground?
A uniform horizontal strut weighs 400.0 N. One end of the strut is attached to a hinged support the wall and the other end of the strut is attached to a sign that weighs 200.0 N The strut is also supported by a cable attached between the end of the strut and the wall. Assuming that the entire weight of the sign is attached at the very end of the s find the tension in the cable and the force at the hinge of the strut.
Suppose a 900-kg car is on the bridge in Figure 9.34 with its center of mass halfway between the hinges and the cable attachments. (The bridge is supported by the cables and hinges only.) (a) Find the force in the cables. (b) Find the direction and magnitude of the force exerted by the hinges on the bridge.
The forearm shown below is positioned at an angle with respect to the upper arm , and a 5.0- kg mass is held in the hand. The total mass of the forearm and hand is 3.0 kg, and their center of mass is 15.0 cm from the elbow. (a) What is the magnitude of the force that the biceps muscle exerts on the forearm for =60 ? (b) What is the magnitude of the force on the elbow joint for the same angle? (c) How do these forces depend on the angle ?
Check Your Understanding For the situation in described in Example 12.5, determine the values of the coefficient s of static friction for which the ladder starts slipping, given that is the angle that the ladder makes with the floor.
A shop sign weighing 195 NN hangs from the end of a uniform 180180-NN beam as shown in (Figure 1). A. Find the tension in the supporting wire (at 35.0∘∘). B. Find the horizontal force exerted by the hinge on the beam at the wall. Express your answer to three significant figures and include the appropriate units. Enter positive value if the direction of the force is to the right and negative value if the direction of the force is to the left.
A student creates a beam bridge for a project, suspends masses from the bridge, and spans the bridge across two surfaces, as pictured below. What is the best approximation for the normal force applied on the bridge’s surface from PylonA? (A)About 0.8N (B)About 1.2N (C)About 1.4N (D)About 2.0N
The large quadriceps muscle in the upper leg terminates at its lower end in a tendon attached to the upper end of the tibia (see Figure a). The forces on the lower leg when the leg is extended are modeled as in Figure b, where T is the force of tension in the tendon, w is the force of gravity acting on the lower leg, and F is the force of gravity acting on the foot. Find T when the tendon is at an angle of 25.0° with the tibia, assuming that w = 29.0 N, F = 12.3 N, and the leg is extended at an angle ? of 40.0° with the vertical. Assume that the center of gravity of the lower leg is at its center and that the tendon attaches to the lower leg at a point one-fifth of the way down the leg. (Give the magnitude.)
A uniform drawbridge must be held at a 36.5 angle above the horizontal to allow ships to pass underneath. The drawbridge weighs 45000 N, is 14.0 m long, and pivots about a hinge at its lower end. A cable is connected 4.00 m from the hinge, as measured along the bridge, and pulls horizontally on the bridge to hold it in place. A) What is the tension in the cable? Express your answer in newtons. B) Find the magnitude of the force the hinge exerts on the bridge. Express your answer in newtons. C) Find the direction of the force the hinge exerts on the bridge. Express your answer in degrees. D) If the cable suddenly breaks, what is the initial angular acceleration of the bridge? Express your answer in radians per second squared.
A 20 N ball is supported by an incline and a cable making an angle α with thevertical direction. Knowing the force in the cable equal to 5 N, determine theangle α and the force exerted by the ball on the incline. Consider the ball as aparticle. Draw FBD
Replace the two forces and one couple acting on the rigid pipe frame by their equivalent resultant force R acting at point O and a couple MO. MC = 30 lb-ft, F = 30 lb, and P = 90 lb. Find only the magnitude of MO in lb.in.