The flexible loop in Figure has a radius of 23 cm and is in a magnetic field of magnitude 0.150 T. The loop is grasped at points A and B and stretched until its area is nearly zero. If it takes 0.200 s to close the loop, what is the magnitude of the average induced emf ( in units of mV) in it during this time interval? A В Select one: A. 71.74 B. 124.64 C. 103.48 D. 177.54 E. 230.44

The flexible loop in Figure has a radius of 23 cm and is in a magnetic field of magnitude 0.150 T. The loop is grasped at points A and B and stretched until its area is nearly zero. If it takes 0.200 s to close the loop, what is the magnitude of the average induced emf ( in units of mV) in it during this time interval? A В Select one: A. 71.74 B. 124.64 C. 103.48 D. 177.54 E. 230.44

University Physics Volume 2

18th Edition

ISBN:9781938168161

Author:OpenStax

Publisher:OpenStax

Chapter13: Electromagnetic Induction

Section: Chapter Questions

Problem 76CP: A 0.50-kg copper sheet drops through a uniform horizontal magnetic field of 1.5 T, and it reaches a...

See similar textbooks

Similar questions

A solenoid with 4 x 107turns/m has an iron core placed in it whose magnetic susceptibility is 4.0 x 103. (a) If a cent of 2.0 A flows through the solenoid, what is the magnetic field in the iron core? (b) What is the effective surface current formed by the aligned atomic current loops in the iron core? (c) What is the self-inductance of the filled solenoid?
The square armature coil of an alternating current generator has 200 turns and is 20.0 cm on side. When it rotates at 3600 rpm, its peak output voltage is 120 V. (a) Wliat is the frequency' of the output voltage? (b) What is the strength of the magnetic field in which the coil is turning?
A single-turn circular loop of wire of radius 50 mm lies in a plane perpendicular to a spatially uniform magnetic field. During a 0.10-s time interval, the magnitude of the field Increases uniformly from 200 to 300 mT. (a) Determine the emf Induced in the ioop. (b) If the magnetic field is directed out of the page, what is the direction of the cun-ent induced in the loop?
A 500-turn coil with a 0.250m2 area is spun in Earth’s 5.00105T magnetic field, producing a 12.0-kV maximum emf. (a) As what angular velocity must the coil be spun? (b) What is unreasonable about this result? (c) Which assumption or premise is responsible?
A flat, square coil of 20 turns that has sides of length 15.0 cm is rotating in a magnetic field of strength 0.050 T. If tlie maximum emf produced in die coil is 30.0 mV, what is the angular velocity of the coil?
(a) A nonferrous screwdriver is being used in a 2.00 T magnetic field. What maximum emf can be induced along its 12.0 cm length when it moves at 6.00 m/s? (b) Is it likely that this emf will have any consequences or even be noticed?
A long, cylindrical solenoid with 100 turns per centimeter has a radius of 1.5 cm. (a) Neglecting end effects, that is the self-inductance per unit length of the solenoid? (b) If the current through the solenoid changes at the rate 5.0 AJs, what is the emf induced per unit length?
A solenoid is wound with 2000 turns pet meter. When the cuiient is 5.2 A, what is the magnetic field within the solenoid?
The accompanying figure shows a metal disk of inner radius r1 and other radius r2 rotating at an angular velocity while in a uniform magnetic field directed parallel to the rotational axis. The brush leads of voltmeter are connected to the dark's inner and outer surfaces as shown. What is the reading of the voltmeter ?
The conducting rod shown in the accompanying figure moves along parallel metal rails that are 25-cm apart. The system is in a uniform magnetic field of strength 0.75 T, which is directed into the page. The resistances of the rod and the rails are negligible, but the section PQ has a resistance of 0.25 . (a) What is the emf (including its sense) induced in the rod when it is moving to tire right with a speed of 5.0 m/s? (b) What force is required to keep the rod moving at this speed? (c) What is the rate at which work is done by this force? (d) What is the power dissipated in the resistor?
The armature and field coils of a series-wound motor have a total resistance of 3.0 . When connected to a 120-V source and running at normal speed, the motor draws 4.0 A. (a) How large is tire back emf? (b) What current will the motor draw just after it is turned on? Can you suggest a way to avoid this large initial current?
Check Your Understanding (a) What is the magnetic flux through one turn of a solenoid of self- inductance 8.0 × 10-5 H when a current of 3.0 A flows through it? Assume that the solenoid has 1000 turns and is wound from wire of diameter 1.0 mm. (b) What is the cross-sectional area of the solenoid?