The flow rate for the pipe system is 0.050 m³/s with a total head loss of 12 m. Use C = 120 for all pipes. 2 3 Pipe Length Diameter 1 400 m 200 mm 2 500 m 180 mm 3 300 m 4 620 m 250 mm a. Calculate the head loss in pipe #2. 2.81 m b. Solve the rate of flow in pipeline #3. 0.0278 m³/s c. Compute the diameter of pipe #3. 176.54 mm

The flow rate for the pipe system is 0.050 m³/s with a total head loss of 12 m. Use C = 120 for all pipes. 2 3 Pipe Length Diameter 1 400 m 200 mm 2 500 m 180 mm 3 300 m 4 620 m 250 mm a. Calculate the head loss in pipe #2. 2.81 m b. Solve the rate of flow in pipeline #3. 0.0278 m³/s c. Compute the diameter of pipe #3. 176.54 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. Compute the head loss in a pipe with diameter 300 mm for a length of 15,000 meters and carrying a flow of 0.097, if f=0.02. (Hint: Use h=(0.0826fL(Q^2))/(D^5)
In the pipeline shown in the figure, the diameter of all pipes (D) is 200 mm and their friction coefficient (f) is 0.02. Thisfor pipeline a) Calculate the maximum flow and draw the hydraulic slope plot. b) Flow rate Q=0.05 m3 To reduce to /s, calculate the required head loss on the valve and calculate the hydraulic slope line.draw. c) HP = 15 – 2000Q2 (Q:m3 /s, Hp: m) placement of a pump with characteristic equation at point BCalculate the flow rate and draw the hydraulic gradient line. Note: The criteria for 3 m < P/γ < 80 m and 0.5 m/s < V < 2 m/s along the pipeline must be met for all cases.
A pipe is carrying 3.26x10-4 m³/s of flow. If C=100, diameter=25 mm, length=21 m. Determine the head loss in this pipe.
Write legibly Complex Pipeline System_Parallel Pipes 1. The pressure heads at junctions A and E are 70.0 m and 46.0 m, respectively, in the given parallelpipe system shown in the figure. Theflow rate of water entering junction A is 0.30 cms. Assuming that the Hazen – Williams roughness coefficient C = 120 for all pipes, determine the flow rate through each branch of the loop. For the solution, use the Hazen – Williams formula. Answer: a. Pipe ABE = _______________________ cmsb. Pipe ACE = _______________________ cmsc. Pipe ADE = _______________________ cms
If the total flow of 4.0m3/? takes place in the three pipes. Determine the distribution offlow. The pipe lengths, diameters and frictions factors are shown below.
Fluid flows at the rate of 0.272 m/s in a 925 mm diameter pipeline 588 m. long. Specific gravity of fluid is 0.57. Neglecting minor losses and f= 0.012. Compute the head loss in m. A. 2.684 B. 0.594 C. 3.92 D. 0.064 A system of pipes consists of a 10 inches pipe 2,500 ft. long and an 8 inches pipe 3,600 ft. Long. If Q = 650 gpm and f = 0.013, find the equivaient diameter of the pipes when the pipes are in series. A. 0.811 ft B. 0.911 ft C. 0.711 ft D. 1.11 ft ft
Water is siphoned from the tank as shown in the figure below. the length of the pipe is 12 m and has roughness ratio (E/D=0.001) a) determine the flow rate and the pressure at point A, stagnation point, neglecting all loses. b) determine the flow rate and pressure at point A, stagnation point, assuming only the major loses are important c) determine the flow rate and pressure at point A, stagnation point, assuming all loses (minor and major) are important.
1. A 36 inch diameter pipe is 4000 feet long and has a head loss of 12.7 feet. a. Solve for the discharge capacity of the pipe according to Manning's Formula. Use n=0.016.
Water flows in a 350mm- diameter pipe at the rate of 600 liters per second. The pipe has a length of 64m. Compute the head loss using Darcy Weisbach formula with f=0.028. Compute the head loss using Hazen William’s Formula with C=92. Compute the head loss using Manning’s formula with n=0.012
aa 552-mm diameter pipeline, 68 m. long carries 768 L/s of water. compute the head loss (in meters) using Darcy Weishback with f = 0.0165.
Pipes 1, 2 and 4 are connected in series with pipes 2 & 3 parallel to each other.Pipelines Diameter Length Friction Factor1 350mm 2500m 0.022 400mm 4000 m 0.023 300mm 2000 m 0.024 450mm 2500 m 0.02If the discharge of pipeline 2 is 0.05 m^3/s,1. Compute the rate of discharge of pipeline 32. Compute the rate of discharge of pipeline 43. Compute the total headloss of the pipe system
1. A pipe has a slope of 1 in 100 and its length is 300 meters. Its diameter is 0.6 meter at the lower end while 1.2 meters at the higher end. The rate of flow through pipe is 5400 liters/min. Find the pressure at the lower end if the pressure at higher end is 68.07 kPa. Neglect losses.