The following data refers to an air conditioning system to be designed for an industrial process for hot and wet climate. Outside conditions = 38o C DBT and 74 % RH. Required conditions are 23o C DBT and 65 % RH. This is achieved by cooling and dehumidifying and then by heating. If 42 m 3 of air is absorbed by the plant every minute, find the capacity of cooling coil in TR, capacity of heating coil in kW and amount of water removed per hour

The following data refers to an air conditioning system to be designed for an industrial process for hot and wet climate. Outside conditions = 38o C DBT and 74 % RH. Required conditions are 23o C DBT and 65 % RH. This is achieved by cooling and dehumidifying and then by heating. If 42 m 3 of air is absorbed by the plant every minute, find the capacity of cooling coil in TR, capacity of heating coil in kW and amount of water removed per hour

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter45: Domestic Refrigerators And Freezers

Section: Chapter Questions

Problem 12RQ: Refrigerators currently being manufactured in the United States are using______as their refrigerant.

See similar textbooks

Similar questions

An air handling unit receives re-circulated room air at 23 oC DBT and 50% RH and flow at 2 m3/s, and fresh air at 5 oC and 30% RH with a flow rate of 0.05m3/s, the mixed air is then heated to 35 oC DBT. Calculate each point condition and the load of heater battery in kW
A steam power plant has a high pressure of 2.5 MPa after release from the pump and it maintains 40°C in the condenser. The quality of the stream exiting the turbine is 80%. Solve for the work produced by the turbine and the pump, the heat transfer in the boiler, and heat removed by the condenser. (Answer in kJ/kg)
A refrigerated compartment is maintained at a temperature of -5°C. Heat from the surroundings, at 25°C, leaks into the compartment at a rate of 1.2 kW. Find the compressor power required to maintain the temperature difference for the following scenarios:
Saturated moist air enters a heating coil at temperature 400F and exit the coil at 1100F . The amount of moist air entering the heating coil is 25000 CFM .Find the amount of heat addition in Btu/min . A) 33465 Btu/min B) 32465 Btu/min C) 30465 Btu/min D) 25465 Btu/min
A small auditorium is required to be maintained at 22 C DBT and 70% RH. The ambient conditions are 30 C DBT and 75% RH. The amount of free air circulated is 200m3/min. The required conditions are achieved by first cooling and dehumidifying through a cooling coil having apparatus dew point of 140C and then by heating. With the help of psychrometric chart, find: i) capacity of cooling coil in TR and its by pass factor, ii) the amount of water vapor removed by the cooling coil in kg/hr, ii) capacity of heating coil in KW and its surface temperature. Assume bypass factor as 0.2 IES1992
A heating system that uses heated water has a total heating load of 587 thousand btuh. How much heated water flow in gallons per minute (GPM) is required to satisfy the total load if the system is designed for 34 °F temperature change?
An ammonia refrigeration compressor takes its suction from the evaporator, at a temperature of-200F and a quality of 95%. The compressor discharges at a pressure of 100 psi, liquid ammonia leaves the condenser at 500F.(a)Determine the heat absorbed by the evaporator in kJ/kg. (b)Determine the heat rejected to the condenser in kJ/kg. (c)Determine the COP. (d)Determine the horsepower per ton of refrigeration. (e)Determine the quality of refrigerant upon entering to the evaporator
The mass flow rate of the refrigerant in a Single Stage Vapor Compression (SSVC) refrigeration system is 0.015 kg/s and the evaporating and condensing temperatures shall be -20°C and 50°C, respectively. Determine the work of compressor in kW.
Determine the rate of heat released (in kW) by the steam with 88.0% quality thatenters the evaporator at 1800 kg/h at 132C and exits as a subcooled liquid at 100C.Assume that the condensate outlet pressure is the same as the steam inlet pressure.The specific heat of liquid water is 4.187 kJ/kg-C
Q4 An apartment in Buraimi requires 74540 Whr of heat during winter season for the month of January to March to retain a constant inside temperature of 295K. What will be the required mass of water for a day’s worth of heat, collector surface area for an all-solar heating system that has 34.65% efficiency? Assume the temperature of the hot water at the outlet of the storage tank is 72.5oC. Take the global radiation in Buraimi for the month of January as 4.02 kWh/m2/day, February as 5.28 kWh/m2 /day and March as 6.06 kWh/m2/day. What changes would you observe in the above
Find the mass of water, in kg, that can be cooled from 24 0C to -80C from a 10 tons refrigeration system for 15 hrs. ANSWER: 4197.930 kg A refrigeration system is used to cool water in the evaporator at 3 kg/s of water from 22 oC to ice. Find the tons of refrigeration required. ANSWER: 364.48805 TR A two stage cascade refrigeration system uses R-11 as the working substance. The evaporator is at -30 0C and the high pressure condenser is at 300C. The cascade condenser is a direct contact type. The refrigeration load is 24 tons. Given that, h2 = 393 kJ/kg; h6 = 408 kJ/kg. Find the mass flow rate in the low pressure loop. ANSWER: 0.4771 kg/s
A room is to be maintained at 25⁰Cdb and 15⁰Cwb. The air supplied to the room is about 90%RH. Outside air is at 35⁰Cdb and 50%RH. The amount of recirculated air is 75% of the total air supplied to the room. If the sensible and latent heat loads are 2,800,000KJ/hr and 700,000 KJ/hr respectively, Determine: (a) total amount of air supplied to the room in Kg/s, (b) amount of outside air, m 3 /s, (c) refrigerating capacity of the cooling equipment, Hp, and (d)average coil surface temperature to be maintained.