The following table gives the lengths of three copper rods, their diameters, and the potential differences between their ends.RodLengthDiameterPotential Difference3dV.2Ld2V3L2d2VIn the following questions, you will be asked to rank these rods. If multiple rods rank equally, use the same rank for each, then excludethe intermediate ranking (i.e. if objects A, B, and C must be ranked, and A and B must both be ranked fırst, the ranking would beA:Greatest, B:Greatest, C:Third greatest). If all rods rank equally, rank each as 'Greatest!.Rank the rods according to the magnitude of the electric field within them.Rod 1Rod 2Rod 3<>123 Rank the rods according to the current density within them.Rod 1Rod 2Rod 3GreatestSecond greatestThird greatestRank the rods according to the drift speed of electrons through them.Rod 1Rod 2Rod 3<>

The following table gives the lengths of three copper rods, their diameters, and the potential differences between their ends. Rod Length Diameter Potential Difference L. 3d 2L d 2V 3L 2d 2V In the following questions, you will be asked to rank these rods. If multiple rods rank equally, use the same rank for each, then exclude the intermediate ranking (i.e. if objects A, B, and C must be ranked, and A and B must both be ranked first, the ranking would be A:Greatest, B:Greatest, C:Third greatest). If all rods rank equally, rank each as 'Greatest. Rank the rods according to the magnitude of the electric field within them. 123

The following table gives the lengths of three copper rods, their diameters, and the potential differences between their ends. Rod Length Diameter Potential Difference L. 3d 2L d 2V 3L 2d 2V In the following questions, you will be asked to rank these rods. If multiple rods rank equally, use the same rank for each, then exclude the intermediate ranking (i.e. if objects A, B, and C must be ranked, and A and B must both be ranked first, the ranking would be A:Greatest, B:Greatest, C:Third greatest). If all rods rank equally, rank each as 'Greatest. Rank the rods according to the magnitude of the electric field within them. 123

Physics for Scientists and Engineers: Foundations and Connections

1st Edition

ISBN:9781133939146

Author:Katz, Debora M.

Publisher:Katz, Debora M.

Chapter29: Direct Current (dc) Circuits

Section: Chapter Questions

Problem 82PQ

See similar textbooks

Similar questions

Assume that the leaf of part A (3.5cm width & 0.2mm thickness) has a length of40cm, and its top & bottom surfaces are shaped like flat plates. The fluid within the leafis mostly water. What is its capacitance?A) 8.85picoFB) 0.049 micro FC) 495600 FD) 80F
If R = 2.0 kΩ, C = 4.0 mF, ε = 8.0 V, Q = 20 mC, and I = 1.0 mA, what is the potential difference Vb - Va?
What is the energy stored in such a cell membrane if the potential difference across it is 7.05×10−2 VV ? Express your answer using two significant figures.
Q4-5-6-7 A rod of semiconducting material of lenght L=3 m and cross-sectional area A=4.5 mm^2 lies along the x-axis between x=0 and x=L. The material obeys ohm's law, and resistivity varies along the rod according to p=p0 (1-(x^2/L^2)) where p0= 4.10^-4 ohm.m. The end of the rod x=0 is at a potential V0=30V greater than the x=L. A) what is the total resistance, in units of ohm, of the rod? B) what is the current, in units of miliamperes, in the rod? C) what is the electric potential, in units of Volt, in the rod at x=L/2? D) what is the electic-field magnitude E, in units of V/m, in the rod at x=L/2?
A capacitor of capacitance C = 3 uF has been charged so that the potential difference between its plates is V0 = 245V. The capacitor is then connected to a resistor of resistance R = 14 kOhm. The switch S is closed, and the capacitor begins to discharge. C = 3 uF V0 = 245 V R = 14 kOhm (b) Calculate the charge Q0 on the capacitor before the switch is closed, in coulombs. (d) Calculate the potential difference VC in volts between the capacitor plates at time t = 5.0 ms after the switch is closed.
Two parallel plates, connected to a 45 volt power supply, are separated by an air gap. How small can the gap be if the air is not to become conducting by exceeding its breaking value of E=3x10^6 V/M
Consider two coaxial conducting spheres of radii a and b = 2a. Filled with a conductive material with resistivity p = p0 (1 + r / a) between the radii (region a≤r≤b). Calculate the resistance between the spheres.
The compressor on an air conditioner draws89.6 A when it starts up. The start-up time isabout 0.282 s.How much charge passes a cross-sectionalarea of the circuit in this time?Answer in units of C.
The current in a certain wire at 20.0°C is 2.40 A when thepotential difference between the ends of the wire is 1.50 V. If the wireis heated to 80.0°C and the potential difference remains the same, thecurrent decreases to 2.00 A. What is the resistance of the wire at 20.0°C? At 80.0°C?
A cylindrical metal wire at room temperature is carrying electric current between its ends. One end is at potential VA = 50 V, and the other end at potential VB = 0 V. Rank the following actions in terms of the change that each one separately would produce in the current, from the greatest increase to the greatest decrease. In your ranking, note any cases of equality. (a) Make VA = 150 V with VB = 0 V. (b) Make VA = 150 V with VB = 100 V. (c) Adjust VA to triple the power with which the wire converts electrically transmitted energy into internal energy. (d) Double the radius of the wire. (e) Double the length of the wire. (f) Double the Celsius temperature of the wire. (g) Change the material to an insulator
A Nichrome heater dissipates 500 W when the appliedpotential difference is 110 V and the wire temperature is 800 C.What would be the dissipation rate if the wire temperature wereheld at 200 C by immersing the wire in a bath of cooling oil? Theapplied potential difference remains the same, and a for Nichromeat 800 C is 4.0 * 10-4 K-1.
In the figure below, what is the potential difference Vd - Vc between points d and c if ℰ1 = 5.0 V, ℰ2 = 1.0 V, R1 = R2 = 11 Ω, R3 = 6.0 Ω, and the battery is ideal. ____________V (please show the units when working through the problem so that I can follow it easier)