The forward-route transfer function is applied to the input of a negative unit feedback system as at the bottom, and the overrun rate is given as %OS=12.6% at the exit of the 31 - G(s) s(s + 2)ª In this case, which of the following is the peak time of the system? system. O A) 3.69 s OB) 3.95 s OC) 3.78 s OD) 3.86 s OE) 4.07 s

The forward-route transfer function is applied to the input of a negative unit feedback system as at the bottom, and the overrun rate is given as %OS=12.6% at the exit of the 31 - G(s) s(s + 2)ª In this case, which of the following is the peak time of the system? system. O A) 3.69 s OB) 3.95 s OC) 3.78 s OD) 3.86 s OE) 4.07 s

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the following sampled-data control system: A) The forward-path transfer function of the system is G(s) = Gh(s)Gp(s). Find the sampled-data transfer function G(z) as a function of the sampling time T. B) Find the closed-loop transfer function of the system, Hcl(z), as a function of T. Compute the range of T that makes the closed-loop system stable.
Briefly describe the effects the switching control signal frequency has on the output voltage and current of a boost chopper. In Dhaka city during the month of May, a 20W rated solar panel supplies 15W of power at an output voltage of 15V & an output current of 1A. But during the month of December, the same solar panel supplies 8.5W of power at an output voltage of 10.5V & an output current of 0.81A. The solar panel is used to charge a 12V battery. Practically, for charging a 12V battery we need to supply 13V.i) In the month of May, the user will need a DC-DC converter (Buck) to charge the battery.a) What will be the duty cycle?b) Assuming that the converter is 100% efficient, what will be the input current to the battery?ii) In the month of December, the user will need a different DC-DC converter (Boost) to charge the battery.a) What will be the duty cycle?b) Assuming that the converter is 100% efficient, what will be the input current to the battery?
A 2W power signal is transmitted through a 40Km cable. A at a distance from the source of 24 km, an amplifier / repeater is placed with a gain of 64dB. The cable has an attenuation constant of 2.5dB/km. Determine a power of the signal at the input of the repeater and at the output of the communications system, that is, at the destination.
A signal transmission line which has a source impedance of 75Ω is to be connected to a signal strength meter of impedance 50Ω which has a maximum display of 18dB. Calculate the values of resistors required in an L-pad attenuator circuit to operate the meter at maximum power (towards small impedance). And also determine minimum insertion loss and minimum attenuation in dB.
1. Consider the state space system with the given picture. Is this a valid state-space system? 2. (sperate problame0 Write down a transfer function of a stable system for which pure proportional feedback could drive the system unstable.
Open loop function of a unity feedback system is given by G(s)=K(s+A) / s(s+1.4)(s+2.9)(s+3.2) For drawing root locus, if the value of Centroid is -2, then The value of A is :
1- Draw the frequency response of the amplifier on a semi-log paper.2- From the frequency response plot, determine the −3 ?? cut-off frequencies ?? and ??of the amplifier, and find the bandwidth.3- Calculate the lower break frequencies ???, ???, and ??? due to the coupling and bypass capacitors. Find the dominant corner frequency and compare it with the measured value of ??.4- From your plot, determine the unity-gain frequency ??.5- Calculate the theoretical value of the mid-band gain, and compare it with the practically measured value.6- What is meant by one decade, and one octave?
SUBJECT IS : control systemQ) Discuss the effect of adding zeros to overall transfer function on system response curve.
Find an expression for the loop gain of the lowpass ﬁlter as shown assuming the ampliﬁer has a ﬁnite gain Ao.
Design a single-sideband AM modulator and demodulator units based on following rules. Design Principles: bandwidth of filter you will design will be 6kHz in case of double sideband solutions. the carrier frequency is 4MHz. a) Determine the values of elements (if any; R, C, and L) used in the circuits. b) In case of noise (added to the modulated signal, What can be the SNR at i/p stage of demodulator? What can be the SNR at o/p stage of demodulator?
The forward transfer function G(s) with a H(s) feedback configuration of an uncompensated Basic Satellite Launching System is as shown in figures 1 and 2. A- in the picture B- Compute the percent overshoot, peak time and settling time, using second order approximation through pole zero cancellation and unity feedback configuration shown in figure 2. C- Summarise the results (a) and (b) in tabular form and comment on the stability of both systems based on time response graph for (a) and computed values in (b).
are given a system’s transfer function as T(s) = 21 Construct a state-space model for the given system using ” Observer Canonical Form” method. | that the full state information of this system is available, design a state-feedback controller for this put the desired closed loop poles at ~2+ 2. Now, assume that the state information of the system are measurable, for this case what kind of controller do you suggest? Design this controller so that the ¢ Joop poles of the system are located at —10 + 510.