The overall transfer function for a unity feedback system is G(s) = 4/(s^2+4s+4).Which of the following statements about this system are correct? 1- Position error constant Kp is 4. 2- System is type 1.3- Velocity error constant is finite . Select the answer as per following code: * О 1,2 O 2, 3 1, 2, 3 О 1,3

The overall transfer function for a unity feedback system is G(s) = 4/(s^2+4s+4).Which of the following statements about this system are correct? 1- Position error constant Kp is 4. 2- System is type 1.3- Velocity error constant is finite . Select the answer as per following code: * О 1,2 O 2, 3 1, 2, 3 О 1,3

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A process has the third-order transfer function (time con-stant in minutes),Gₚ(s)=2/(0.5s+1)³Also,Gᵥ=0.1 and Gₘ=10. For a proportional controller,evaluate the stability of the closed-loop control systemusing the Bode stability criterion and three values of K꜀:1,4, and 20.
A signal transmission line which has a source impedance of 75Ω is to be connected to a signal strength meter of impedance 50Ω which has a maximum display of 18dB. Calculate the values of resistors required in an L-pad attenuator circuit to operate the meter at maximum power (towards small impedance). And also determine minimum insertion loss and minimum attenuation in dB.
Open loop transfer function G(s) = K/ s(s+3)(s+4) for a system with a) Using the Routh Hurwitz criterion, the poles of the closed-loop system are only purely imaginary. Calculate the value of K for it to have roots on the axis. b) Calculate the maximum value of K for the system to be stable. c) Calculate the values of K for the system to have roots at the value of -1 on the real axis.
Q2. Explain how you would determine the primary and secondary constants of transmission by impedance measurements. Also, explain how the velocity of propagation and attenuation constant can be experimentally determined.
why S-parameters are preferred to other types of two-port parameters at RF frequencies
Find the normalized autocorrelation sequence of the following signal:x(n) = 1, for -3 ≤ n ≤ 3, and equals 0 for other values of n.b) For a recorded data, y(n), modeled by the following difference equation, derive an expression forryy(l) in terms of rxx(l):y(n) = 0.5x(n) + 0.5x(n-1)
What is the effect on the signal–to–noise ratio of a system (in dB) if the bandwidth is doubled, considering all other parameters to remain unchanged except the normal thermal noise only? The S/N will be ______. I need answer ASAP. Thank you!
The amplitude of the modulating tone is decreased in the above example until the to-tal power is 45 kW. Assuming that the carrier power remained constant, compute thenew modulation index and transmission efficiency.
Using the orthogonality of sine and cosine makes it possible to transmit andreceive two different signals simultaneously on the same carrier frequency. A scheme to dothis, known as quadrature multiplexing or quadrature amplitude modulation (QAM), is shown in Figure a) Write down the expression for ( ) QAM x t ?b) Derive the two expressions for the outputs 1 y t( ) and 2 y t( ) after the demodulator andlow pass filter.c) Consider the situation when the receiver is not exactly synchronised with thetransmitter, thus the demodulator at the receiver has a slight frequency shiftcos(2 ( ) ) c π f ft + ∆ where ??∆ ≪ ????. Derive the two expressions for the outputs 1 y t( )and 2 y t( ) after the demodulator and low pass filter for this case (Consider only thenoise free situation).
?? = 1.58??a) ?? =?b) ?? =?c) ?? =? e)lowercutoff frequency d)upper cutoff frequency C?? = 3??, ??? = 4??, ??? = 4??, ??1 = ??2 = 10?F
Answer the following: (a) What is the maximum data rate for a 64-level system with an analog bandwidth of 400 MHz? (b) What is the maximum data rate if that same system is subject to noise, with an average power level of 600 and an average noise level of 200? Include units in your final answer.
Open loop transfer function G( s ) = K/ s(s+3)(s+4) for a systema) using the Routh Hurwitz criterion, the poles of the closed loop system are purely imaginary calculate the value that K will get so that it has roots on the axis.b) calculate the maximum value that K will receive so that the system can be stablec) calculate the values that K will get so that the system can have roots at -1 on the real axis