The fuel gage for a gasoline tank in a car reads proportional to its bottom gage. The tank is 35 cm deep and accidentally contaminated with 3 cm of water. Specific gravity of gasoline is 0.68. If the tank has a uniform horizontal cross-sectional area of 0.45 m2, how many liters of gasoline are required to fill the tank? Select the correct response: 9.53 L 7.41 L 6.35L 8.47L The fuel gage for a gasoline tank in a car reads proportional to its bottom gage. The tank is 35 cm deep and accidentally contaminated with 3 cm of water. Specific gravity of gasoline is 0.68. What is the gage reading when the tank is filled with gasoline? Select the correct response 2.87 kPa 2.11 kPa 2.56 kPa 2.34 kPa

The fuel gage for a gasoline tank in a car reads proportional to its bottom gage. The tank is 35 cm deep and accidentally contaminated with 3 cm of water. Specific gravity of gasoline is 0.68. If the tank has a uniform horizontal cross-sectional area of 0.45 m2, how many liters of gasoline are required to fill the tank? Select the correct response: 9.53 L 7.41 L 6.35L 8.47L The fuel gage for a gasoline tank in a car reads proportional to its bottom gage. The tank is 35 cm deep and accidentally contaminated with 3 cm of water. Specific gravity of gasoline is 0.68. What is the gage reading when the tank is filled with gasoline? Select the correct response 2.87 kPa 2.11 kPa 2.56 kPa 2.34 kPa

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.8P

See similar textbooks

Similar questions

What would be the weight of one 3-kg mass on planet where the acceleration due to gravity is 10 m/s2? Select the correct response 3 kN 29.43 N 30N 13 KN An open tank contains 5.7 m of water covered with 2.8 m of kerosene. Find the pressure at the interface of the two liquids. Specific weight of kerosene is 8.0 kN/m^3. Select the correct response 22.400 55.917 44.000 33.240
Hydrostatic pressure at any given depth of a liquid depends on the_____ of the container.a)Volumeb)ShapeC)Depthd)All of the above .As the temperature of oil increases, the viscosity of oil willa) increaseb) decreaseC)not change Which of the following units would NOT be used for volume flow rate?a) gal/minb) Ib/sc)m⅗d)ft^3/s 2.Dynamic viscosity is defined as,a) weight per unit volume of a fluidb) volume per unit weight of a fluidc) the velocity gradient divided by the shearing stress of a fluidd)the shearing stress divided by the velocity gradient of a fluid
PROPAGATION OF ERROR You are tasked to supervise the design of 0.5MW wind turbine to be constructed in a Wind Farm in Pililla, Rizal. Suppose the design criteria are as follows: The air density as surveyed after 2 year period averaged at 1.225 kg / cubic meter. The sweeping diameter of the rotor blades is 125m, and the anemometer reading in the area amounts to 4.2m/s on a 2 year period of survey. What is the theoretical power output of the turbine assuming 100% efficiency of operation? Your answer must be in kW and in two decimal places with correct signs. In the previous problem, if the diameter measurement is off by 0.1m and the anemometer reading is also fluctuating by 0.05m/s and if the error measurement for theoretical power output must be limited to 3%, WHY OR WHY NOT should you accept the design? * Show complete solution in paper.
The transducer specified in Table 1.1 is chosen to measurea nominal pressure of 500 cm H2O. The ambient temperature is expected to vary between 18 ∘C and 25 ∘C duringtests. Estimate the possible range (magnitude) of each listedelemental error affecting the measured pressure refering to the solution provided online, Sensitivity error(eK) = (±0.0025)(500 cm H2O)= ± 0.75 cm H2O = ± 0.00375 V how do you get 0.75?? shoud it not be 1.25? according the answer, for sensitivity
An airplane builder wants to build a scaled-down model of a real airplane in a 12:1 ratio in order to be able to perform tests in a wind tunnel. The real plane flies at 126 km/h, while the air speed in the tunnel where the model is located is given by V. The performances of the two will be equivalent for a value of V, in m/s, equal to Data: air viscosity η = 1.8 × 10-5 kg/(m.s) air density ρ = 1.3 kg/m3
Wind blows and pasts a banner causes it to flutter. The fluttering frequency f is a function of the wind speed V, the air density ρ, the acceleration of gravity g, the length of the banner L and the “area density” of the flag material ρA (with dimensions of ML-2 ). In order to estimate the flutter frequency of a large banner with L = 40 ft in a V = 30 ft/s wind, a small banner with L = 4 ft is to be tested in a wind tunnel. (a) What is the area density of the small banner when the large banner has area density of 0.006 slugs/ft2? (b) What should the wind tunnel velocity be to test the small model? (c) It has been shown that the small banner flutters at 6 s-1 when the same area density and wind tunnel velocity are used in parts (a) and (b). In this case, what is the fluttering frequency of the large banner?
Don't skip steps. Show the complete solution for this problem. A golden breast plate weighing 18.63 kg Is dropped in a tub that Initially contains water. After the breast plate was totally submerged. the water level rises by 61.87 cm. The tub has a diameter of 6 centimeters and the breast plate was said to be made only from gold and silver Compute for the percentage of each component of the breast plate if the density of gold Is 19.3 g/cubic centimeter and silver has a density of 10.49 g/cubic centimeter.
A vertical jet thru a nozzle supports a 150.90N weight. The velocity and diameter of the jet are 17.90m/s and 3.90 cm respectively. Find the distance of load from the nozzle in meters. Group of answer choices 13.79 31.79 17.93 71.39I need an answer for this asap :(
Show complete solution and 3 decimal places for the final answer. Asap thanks! A truck carrying fully-filled water container that is 2.5m long, 2.5m wide, and 2m high. The entire mass is 3000kg encountered an unbalanced force of 15kN. Estimate the acceleration in m/s^2.
Table 1 shows the variation of dynamic viscosities of water with absolute temperature. Table 1: Dynamic viscosity of water with absolute temperature. Viscosity µ, Pa.s x 10-³ 1.787 Temperature, K 273.15 278.15 283.15 293.15 303.15 1 313.15 333.15 353.15 373.15 4G 1.519 1.307 1.002 0.7975 0.6529 0.4665 0.3547 0.2828 a) Using excel software, develop a relationship of for viscosity in the form of μ=A+BT+CT² + DT³ + ET. Done Show your trend line regression and standard deviation for linear and polynomial index (quadratic T², cubic T³ and T). b) Using the relationship developed, predict the dynamic viscosity of water at 50 °C at which the reported value is 5.468 x 10 Pa.s. Compare your result with the results of Andrade's equation which is given in the form of μ = D.e BT where D and B are constants whose values are to be determined using viscosity data given.
The drag on an airplane wing in flight is known to be a function of the density of air (), the viscosity of air(), the free-stream velocity (U), a characteristic dimension of the wing (s), and the shear stress on the surface of the wing (s). Show that the dimensionless drag, sU2, can be expressed as a function of the Reynolds number, Us.
The heat transfer between a solid body and a fluid medium is determined by the equation Q=h·A·(Ts-Tf). Here; Q is the amount of heat transferred, h is the heat transfer coefficient, A is the heat transfer surface area, Ts is the temperature of the surface and Tf is the temperature of the fluid. These parameters were measured as h=250±1.75 W/m2ºC, A=20±0.75 m2, Ts =100±0.75ºC and Tf =25±0.75ºC, including error levels. What is the total uncertainty in the amount of heat transferred, in ±%? a. 3.98 b. 4.07 c. 2.73 d. 2.95 e. 3.88