Pressure gauge B is to measure the pressure at point A in water flow as shown in Figure (1). If the pressure at B is kpa, estimate the pressure at A in Kpa. Assume all fluids are at 200 C. Take water density = 1000kg/m3 Mercury Specific gravity = 13.6 Oil Specific gravity = 0.7 Use the last two digits of your ID number for the gauge pressure at B in kpa. SAE 30 oil Gage B 6 cm Mercury 5 cm Water 11 cm flow 4 cm

Pressure gauge B is to measure the pressure at point A in water flow as shown in Figure (1). If the pressure at B is kpa, estimate the pressure at A in Kpa. Assume all fluids are at 200 C. Take water density = 1000kg/m3 Mercury Specific gravity = 13.6 Oil Specific gravity = 0.7 Use the last two digits of your ID number for the gauge pressure at B in kpa. SAE 30 oil Gage B 6 cm Mercury 5 cm Water 11 cm flow 4 cm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In medical work, pressures are often measured in units of mm of H2O because body fluids, including the cerebrospinal fluid, typically have nearly the same density as water. The pressure of the cerebrospinal fluid can be measured by means of a spinal tap. A hollow tube is inserted into the spinal column, and the height to which the fluid rises is observed. If the fluid rises to a height of 160 mm, we write its gauge pressure as 160 mm H2O. a) Sometimes it is necessary to determine whether an accident victim has suffered a crushed vertebra that is blocking the flow of cerebrospinal fluid in the spinal column. In other cases, a physician may suspect that a tumor or other growth is locking the spinal column and inhibiting the flow of cerebrospinal fluid. Such conditions can be investigated by means of the Queckensted test. In this procedure the veins in the patient’s neck are compressed, to make the blood pressure rise in the brain. The increase in pressure in the blood vessels is…
Consider the pressure Drop depends on : characterstic lugth I density gravity g speed of sound с angular velocity w Surface tension 6 Velardy of fluid V Viscosity of M write an an expression of the pressu drop ?
State what is Bernoulli's Priciple for Pressure and Velocity? In 8 sentences only.
Problem: The reading of an automobile fuel gage is proportional to the gage pressure at the bottom of the tank. If the tank is 32 cm deep and is contaminated with 3 cm of water. 1. If the tank is full of gasoline what should be the reading at the gage in Pa? Use γwater = 9790 N/m^3, γgasoline = 6670 N/m^3 and γair = 11.8 N/m^3 2. How many centimeters of air remains at the top when the gauge indicates “full”? 3. If the tank is 0.5 m^2 in area, calculate the volume of gasoline when the gage reads “full”.
A barometer reads 765 mm of Mercury (g=13.6); what is the atmospheric pressure in N/m2.
Books on porous media and atomization claim that the viscosityμ and surface tension Y of a fl uid can be combinedwith a characteristic velocity U to form an important dimensionlessparameter. ( a ) Verify that this is so. ( b ) Evaluatethis parameter for water at 20°C and a velocity of3.5 cm/s. Note: You get extra credit if you know the nameof this parameter.
The volume flow in a water pipe is 9000 m°/h. The pipe length is 80 m, the pipe diameter 1 m. The material data of water are a density of 1000 kg/m? and kinematic viscosity v=10® m7s. A steel pipe with roughness 0.05 mm is used. Determine the pressure drop in the pipe.
(1) A simple, vertical U-tube manometer is used to measure the differencebetween two gas pressures.Write down an equation for the pressure difference in terms of the difference inthe level of the fluid in the manometer. Describe briefly, with the help ofdiagrams, two modifications to the basic design which offer greater sensitivity tosmall pressure differences. Give equations for their use. ii) An extractor fan draws air from a room and delivers it to the surroundingsthrough a 5m long circular duct of diameter 0.1m. The friction coefficientfor the duct flow is 0.002. The fan characteristic, relating its total pressurerise, ∆P (Nm-2) to the volume flow rate is: ∆P = 103−7x104Q 2. What is therate of flow through the duct?You may assume that the room and surroundings are both at atmosphericpressure; state and justify any other assumptions you make.
SAE 10W30 motor oil has a dynamic viscosity of 0.21 kilograms per meter second and a specific gravity of 0.896 (a) What is the density of the motor oil in units of kilograms per cubic meter?
Simulation of laminar gas flow in the pipe with Ansys Fluent Task: 1. Calculate velocity distribution in y axis at inlet and outlet of the pipe. Submit it as a chart. 2. Calculate velocity distribution over the pipe length. Submit it as a chart. Figure. pipe geometry L, m = 16 R, m= 0.15 Inlet velocity, m/s= 0.08 Gas= Oxygen Need proper solution like pdf file, don't need steps by steps. If you can can do it through ansys fluent. Write proper solution on word file or pdf.
Air with density of 1.225 kg/m^3 and viscosity of 1.789 x 10^-5 kg/m-s flows in a wind tunnel, the wind tunnel spped is measured with Pitot tube probe. For a certain run, the stagantion pressure is measured to be 472.6 Pa gage and the statric pressure is 15.43 Pa gage. Calculate the wind tunnel speed. Choose the right answer below: a.16.3 m/s b.18. 3 m/s c.17. 3 m/s d.19. 3 m/s
A 300 mm by 150 mm Venturi meter (c = 0.985) carries 0.0566 m /s of water with a differential gage reading of 0.634 m. What is the specific gravity of the gage liquid?