The given figure is a representation of a piston inside a cylinder. What do you call parts A, B, C, D, & E respectively?   a. Bore, Top dead Center, Bottom Dead Center, Stroke, Clearance Volume b. Bore, Top dead Center, Bottom Dead Center, Stroke, Swept Volume c. Stroke, Top dead Center, Bottom Dead Center, Bore, Clearance Volume   Show explain. Please answer honestly and do not just guess. Thank you :)

Q: A spherical balloon is inflated so that its volume is increasing at the ft3 rate of 9 min the radius…

A: Write the expression for the volume of the spherical balloon.

Q: Find pressure the pistoni

A: Given data;  Piston diameter,d=30 cm Force,F=3000NFind pressure on the piston ?

Q: An engine has eight cylinders. It has a bore cross-sectional area of 42 cm2 and a stroke of 10 cm.…

A: The number of cylinders (n) = 8  Area of each cylinder (A) = 42 cm2 L = 10 cm

Q: F. A living room is 7.2 m long and 4.5 m wide. What size would it be on a plan drawn to a scale of…

A:

Q: Convert horsepower to Joule... show every step

A:

Q: Calculate the magnitude

A: The provided force system is shown below.

Q: 1. For the shown hydraulic jack the gage pressure indicates 140 kpa how much kilograms should be…

A:

Q: A petrol engine has a cylinder diameter and stroke of 120mm and 210 mm respectively. The clearance…

A: Given data, D = 120 mm = 0.12 m L = 210 mm = 0.21 m Vc = 0.00029 m3 Find: V = ?

Q: mäi 15 Q4The Trigonometric functions for the fig. below are B.

A: Solution    cos A = a / c , cos B = b / c    sin A = b / c , sin B = a / c    tan A = b / a , tan B…

Q: n in the figure. If the drum

A:

Q: For pressure gages, the maximum reading it can give is called the _____ of the gage.

A:

Q: traight to the point. How far was he originally from the point, and how far did he travel in…

A: Hunter is at point A and desired to go to point P. He travelled half due east and turns 120° left.…

Q: The piston diameter of a 6-stroke 1-cylinder gasoline engine is given as 4.25 inch mm, the piston…

A:

Q: 4. If 6.5 m³ of oil weighs 46,800 N, calculate its density in kg/m³. (a) 285 (b) 258 (c) 82 (d) 734

A: Given:V=6.5 m3W=46,800 N

Q: The bar will induce

A: No stress (A)

Q: elocity at a point inside

A: given:x=20cm

Q: (b) 1489.5m³ (C) 128

A: given:bore diameter d=68mmstroke length l=75mm

Q: erature is 32 ASSUMPTIC

A: Given: m= 5 kg  T1  =1500 C  T2 = 3200 C

Q: and the

A:

Q: Efficiency of square

A: Given: Efficiency of square threaded screw is expressed as ? Where,  Square threaded screw is used…

Q: Q4 Locate the cenroid -12 in. -12 in - 15 in. 15 in. 25 in. 9 in.

A: we know that the centroid of a right circular cone is at  a distance of  14th of its…

Q: If the specific gravity of the unknown fluid is 13.92, what is its specific weight in lbf/ft^3?…

A: Given data Specific gravity = 13.92

Q: One acre equals 43,560 ft2. One gallon equals 231 in.3.Determine the number of liters of water in…

A: Given data: The volume of water, V = 2500 acreˑ One acre = 43,560 ft2. One gallon = 231 in3. Here,…

Q: unit of a is

A: Given; Van der Walils equation of state is;  p±v-b=RT where,   p= pressure v= specific volume  T=…

Q: Solve question 8 please

A: Solution to Q8 as mentioned by the student:

Q: The speed of the barrell, vB, m/s is,

A: Solution:

Q: symbol equations is

A: True.

Q: A vertical cylindrical tank 3.66 m. in diameter and 5.32 m. high is full of water. If the tank is to…

A: Here z = 5.32-0.71 = 4.61 m ( depth of parabola created)

Q: A tire gauge registers 32 lbs/in^2 when air in a certain tire is at 10°C. After running for a time,…

A:

Q: The Figure to the right shows a manufacturing process? What is this process called? 2. Identify the…

A: Given :-  1. What is the process called ?

Q: O cm, DC = 30 cm, AD = 20 cr kes an angle of 180° with AD velocity of 3 rad/sec in counte ngular…

A:

Q: n the table given below. -Excel and determine the fluid types. (Show your o you use to describe the…

A: Given data velocity gradient and shear stress are given  Required  Graph between gradient and shear…

Q: do is

A: Given; Hollow shaft;  Where data is given is;    do=2di  power,P= 20 kW N=3000 RPMMax. permissible…

Q: A large hook sticks into a pencil. The hook and pencil are balanced on the edge of a table, as…

A: Center of mass of the object is the point where entire mass of the object is supposed to be…

Q: For the given data, the value of :distance L is Given flexural Sreas= Sees Ps: cAsectte

A: The given simply supported beam is as shown below, Since this is a symmetric beam with udl over its…

Q: Each cylinder of six cylinder internal combustion engine has a diameter of 60 mm and a stroke length…

A: Given Data Diameter of cylinder is :d=60 mm Stroke length is :L=400 mm No of cylinders is :N=6 Now…

Q: The distance

A: Given; A body of mass , M=10 kg Initially stationary on , θ=450Inclined plane as shown as shown in…

Q: The displacement of a piston in cubic inch with a cylinder bore of 7.62-cm and the stroke is 3-

A: Given:d=7.62 cml=3 in

Q: Can you plug in the formula for area show A=

A: Given data  To find the area of the given cross section.

Q: State and prove Dimension Theorem.

A: In mathematics, the dimension theorem for vector spaces states that all bases of a vector space have…

Q: The number of units to be produced by the firm such that the profit

A: Given; Cost function for a product in a firm is given by= 5sqWhere,   q= ampount of productionThe…

Q: B Fig. 4

A:

Q: Kinetil energy ?

A: Given; Thickness=30 mmradius,r=300mmmass,m=30kgN=750 rpmKinetic energy ?

Q: A hydraulic jack has a pump with a piston that is 5.9 mm diameter and a ram that has a 28.5 mm…

A: Write the formula for the output on the hydraulic jack. F1A1=F2A2 Here, F1 is the force input to the…

Q: ment at midspan (in kip-ft to one decimal) for the following bear kip/ft, L = 26 ft, and a = 6 ft.…

A:

Q: Weight is a Vector quantity Select one: O True

A: Weight is a force which is a vector and has a magnitude and direction.  Mass is a scalar. Weight and…

Q: 3: take the mom sums about point(C,D,ERA) ........**.

A:

Q: Based on the picture, devolep 5 question on calculation

A: From the given data: Question: Calculate the PV diagram for water. Mention critical point, critical…

Q: Sketch a typical turbine speed (rpm) VS wind speed characteristics (which indicates how turbine…

A: Given :- Rated speed = 18 rpm

Metal Casting

Metal casting is described as a manufacturing process in which a mold cavity is produced by sand, and molten metal is filled inside a mold cavity. The desirable shaped object is achieved after the solidification of molten metal. Large metal objects like machine beds, motor bodies, and others can easily be manufactured using metal casting. The place or shop where metal casting is performed is called foundry.