Answered: The graphical representation of fatigue…

The graphical representation of fatigue strength on the Y axis to the number of stress cycles on the X axis is called as Gerber Line O S-N Curve O Soderberg Line O Goodman Line

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.26P: - 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v...

See similar textbooks

Related questions

Q: The shaft shown in the figure left has the diameters 304 Stainless steel - 2014-T6 Aluminum and…

Q: Maximum Principal Stress Theory is not good for brittle materials. a) True b) False

A: Given statement - Maximum Principal Stress Theory is not good for brittle materials.

Q: You have been given the S-N plot below for a test material: What is the Fatigue Limit for this test…

A: S-N curve represents fatigue life against a fatigue load.

Q: pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE…

Q: Q.3 a - What are the most preffered properties in metals to be used in high temp. to resist creep…

A: Properties of material which are used to resist the creep. *** AS per our company policy we are…

Q: Which can improve the fatigue resistance of materials? Check the right answers a) eliminate sharp…

A: It is required to choose correct Answer

Q: 1. Define the Kinematic Analysis, 2. What are the fundamental structures? Give an example for each…

A: Since we only answer one question at a time, we will answer the first one. Please resubmit the…

Q: The principal stresses at a point in a critical section are sigma_{1} = 60MPa sigma_{2} = 5MPA and…

Q: 8. A rigid bar AB is supported by three rods. A load P = 275 kN is applied to %3D the bar. The…

Q: A material is made in square cross section of side 1 cm. When 2kN force applied on the material.…

A: given square cross section of side (S)=1 cm s = 10mm…

Q: Find the approximate prime plane in degrees for the state of stress given in the figure. 45 MP 00…

A: Given: Normal stress in x-direction σx=100 MPa. Normal stress in y-direction is σy=60 MPa. Shear…

Q: The allowable tensile stress for wires AB and AC is allow 190 MPa. The applied load is P = 7.8 kN.…

A: Given that: Maximum allowable stress = 190 MPa The applied load P = 7.8 kN For the given…

Q: Select the appropriate Stress -Strain plot which is the most brittle from the following graph A A. A…

Q: Q2) A machine component is subjected to fluctuating stress that varies from 60 to 120 N/mm. The…

A: As given σmax= 120 MPa, σmin = 60 MPa, σmean = σmax+σmin2so σmean=120+602= 90 MPa σa= σmax-…

Q: Use Hooke's Law to calculate the shear modulus of the specimen. answer: G = i MPa

Q: When the shear stress is applied to homogeneous isotropic material,it will only produce shear strain…

A: Consider the diagram shown below for the shear stress on an element.

Q: For the given plane strain state, use Mohr's circle to determine the strain state associated with…

A: Write the given data. εx=-500εy=250γxy=120θ=-15°

Q: 2- A tensile test specimen of stainless steel alloy having a diameter of 0.495 in. and a gage length…

A: Given: Dia-0.495 in. Gauge length = 2 in

Q: A bar made of a brittle material subjected to pure torsion beyond its strength will fracture at…

A: It is required to choose correct option

Q: A cylindrical specimen of some metal alloy of 9 mm in diameter is stressed elastically in tension. A…

A: The force acting on the specimen is F = 15500 N The diameter of the area is d = 9 mm. So, the area…

Q: You have been given the following fatigue data: Cycles to failure 40000 100000 300000 1000000…

A: Given: To find: Fatigue strength at 6 x 105 cycles

Q: 2- A tensile test specimen of stainless steel alloy having a diameter of 0.495 in. and a gage length…

A: Tensile testing is a destructive method of testing an object's strength. Constant tension is applied…

Q: According to the maximum strain energy hypothesis, what should be the length L2 in order for the…

A: Given dataTransverse load F1 = 18kNAxial load F2 = 20kNLarger diameter D = 58mmSmaller diameter d =…

Q: For the system shown in Figure 1A. The fillet of 6 mm radius for this member is critical.…

Q: DRAW THE STRESS-STRAIN DIAGRAM AND LABEL IT PROPERLY.

Q: The stress- strain curve for four materials are shown in figure below. Which material (A/B/C/D) has…

Q: 4. The maximum stress a human tendon can withstand is estimated to be 1200 MPa. If you were to test…

A: 4. According to question, The maximum stress a human tendon can withstand is estimated to be…

Q: Which of the following is true for an infinitesimal stress element? (T in the options below refers…

A: Given strain are complimentary shear strain with equal magnitude.

Q: 4. An unknown metal cube measures 3.5 x 10 -2m decreases a volume of 5.8 x 10 -8m ³. At what stress…

Q: A material is subjected to plane stress. Express the distortion energy theory of failure in terms of…

A: According to distortion energy theory for plane stress : σ12-σ1σ2+σ22=σY2 here, σ1,σ2 are principal…

Q: is a graphical representation of fatigue strength on the Y-axis and the number of stress cycles on…

A: Answer The S - N Diagram is a graphical representation of fatigue strength on the Y-axis and the…

Q: 85. During a hign cycle fatigue test, a metallic specimen is subjected to cyclic loading with a mean…

A: Given data, σmean= 140 MPa, σmin = 70 MPa

Q: The is a graphical representation of fatigue strength on the Y-axis and the number of stress cycles…

Q: The state of strain at the point on the pin leaf has components of € = 200(10-6) Ey 180(106), and…

Q: 3. Which statement is correct? (1 pt) (a) Normal stress is proportional to normal strain (b) Shear…

A: 3) option a is correct.

Q: Q: 1 Define the following and give the formula if exists? 1. Poisson's ratio 2. Brittleness 3.…

A: Let's us one by one define each of the following topics

Q: QN 72+ A rectangular plate, 15 mm thick, made of a brittle material is shown in Figure. Calculate…

A: Given: the thickness of plate, t = 15 mm The width of plate, b = 25 mm The diameter of smallest…

Q: The factors that creep rate depends on? Write 4 of them. Plot the creep-load curve and show its…

Q: mber show below. Explain in detail, the alternative load application direction on the

Q: A steel rod with a cross sectional area of 150 sq.mm is stretched between two fixed points. The…

A: Given Data Area, A=150mm2. Tensile load, T=5000N Initial temperature, 20C

Q: 7. The point where the stress-strain diagram for structural steel becomes almost horizontal is…

A: The stress -strain diagram for the steel is as follows:

Q: The principal stresses at the critical point of a part were found to be as shown. Using the…

Q: Q-8 A tensile test specimen of stainless steel alloy having a diameter of 12.6 mm and a gage length…

A: Part (a) Modulus of elasticity: It is defined as the ratio of longitudinal stress and strain. In a…

Q: n the Haigh diagram depicted in figure, point A represents the fatigue stress in a standard screw…

A: Solution:

Q: Question 5: Based on the stress-strain diagram for a material shown here, find the followings: Yield…

Q: In stress strain curve the maximum stress the material withstand without breaking is represents by…

A: Answer-

Q: 1.5 The principal stresses induced at a point in a machine component made of steel 50C4 (S= 460…

Q: 9- For the figure shown, which of the following statements is true: Material 1 is a ductile…

A: Solution:

Q: During a high cycle fatigue test, a metallic specimen is subjected to cyclic loading with a mean…

Concept explainers

Strain energy

The term strain indicates the variation in an object's length, area, and volume when the object is subjected to an external force. The external force may be of normal, shear, moment, torque, etc. The strain in an object depends on the types of external force and cross-section of the object. Mathematically, the evaluation of strain can be obtained with the help of elastic constants.

Question

The graphical representation of fatigue strength on the Y axis to the number of stress cycles on the X axis is called as
Gerber Line
O S-N Curve
O Soderberg Line
O Goodman Line

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

On the surface of a structural component in a space vehicle, the strains arc monitored by means of three strain gages arranged as shown in the figure. During a certain maneuver, the following strains were recorded: e, = 1100 X l0_6, 6h = 200 X lO_6, and e = 200 X 10-6. Determine the principal strains and principal stresses in the material. which is a magnesium alloy for which E = 6000 ksi and v = 0.35. Show the princ ipal strains and principal stresses on sketches of properly oriented elements.
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
A solid spherical ball of magnesium alloy (E = 6.5 × l0-6 psi, v = 0.35) is lowered into the ocean to a depth of 8000 ft. The diameter of the ball is 9.0 in. (a) Determine the decrease ?d in diameter, the decrease, ?V in volume, and the strain energy U of the ball. (b) At what depth will the volume change be equal to 0.0324% of the original volume?
During a test of an airplane wing, the strain gage readings from a 45° rosette (see figure) are as follows: gage A, 520 × l0-6; gage B. 360 × l0-6; and gage C,-80 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
Solve the preceding problem for an aluminum plate with h = 10 in.. i = 0.75 in., E = 10,600 ksi, v = 0.33. P = 96 kips. Pt,. = 24 kips. and V =18 kips. For part (b) of Problem 7.5-12, assume that the required strain energy stored is 640 in.-lb. In part (c). the change in volume cannot exceed 0.05%.
The rails of a railroad track are welded together at their ends (to form continuous rails and thus eliminate the clacking sound of the wheels) when the temperature is 60°F. What compressive stress ?? =6.5×10-6 /? is produced in the rails when they are heated by the sun to 120"F if the coefficient of thermal expansion a = the modulus of elasticity E = 30 × 106 psi?
- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
Solve the preceding problem if the cross- sectional dimensions are b = 1.5 in. and h = 5.0 in., the gage angle is ß = 750, the measured strains are = 209 × 10-6 and B = -110 × 10, and the material is a magnesium alloy with modulus E = 6.0 X 106 psi and Poisson’s ratio v = 0.35.
The statically indeterminate structure shown in the figure consists of a horizontal rigid bar AB supported by five equally spaced springs. Springs l, 2, and 3 have stiff nesses 3k, 5k. and k, respectively. When unstressed, the lower ends of all Five springs lie along: a horizontal line. Bar AB. which has weight W, causes the springs to elongate by an amount S. (a) Obtain a formula For the total strain energy of the springs in terms of the downward displacement d of the bar. (b) Obtain a formula for the displacement S by equating the strain energy of the springs to the work done by the weight W.
A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the figure. The width of the plate is h = 12.0 in. Measurements show that the normal strains in the x and v directions are s = 427 × 10-6 and s = 113 × l0-6, respectively. With reference to part b of the figure. which shows a Iwo-dimensional view of the plate. determine the following quantities. (a) The increase .d in the length of diagonal Oil. (b) The change . in the angle between diagonal Oti and the x axis, (c) The shear strain y associated with diagonals Oil and cf(that is. find the decrease in angle ced).
A prismatic bar in tension has a length L = 2.0 m and cross-sectional area A =249 mn2. The material of the bar has the stress-strain curve shown in the figure. Determi ne t he elongation 5 of the bar for each of the following axial loads: P = 10 kN, 20 kN, 30 kN, 40 kN. and 45 kN. From these results, plot a diagram of load P versus elongation 5 (load-displacement diagram).
An element of material in plain strain has the following strains: x = 0.001 and y = 0.0015. (a) Determine the strains for an element oriented at an angle = 250. (b) Find the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.