The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB is 6.6 kN. Determine the required tension Tin cable AC such that the net effect of the two cables is a downward force at point A. Determine the magnitude R of this downward force. Assume a = 30 m, b = 41 m, c = 18 m, and d = 26 m. B Answers: T = R= i i A - F KN KN

The guy wires AB and AC are attached to the top of the transmission tower. The tension in cable AB is 6.6 kN. Determine the required tension Tin cable AC such that the net effect of the two cables is a downward force at point A. Determine the magnitude R of this downward force. Assume a = 30 m, b = 41 m, c = 18 m, and d = 26 m. B Answers: T = R= i i A - F KN KN

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter23: Electromagnetic Induction, Ac Circuits, And Electrical Technologies

Section: Chapter Questions

Problem 24PE: Integrated Concepts The Tethered Satellite in Figure 23.12 has a mass at 525 kg and is at the end of...

See similar textbooks

Similar questions

Find the tension in the cable AC. 89N -29N 55N 23.6N
Two forces of magnitude Ta = 12 kips and Tb = 18 kips are applied as shown to a welded connection. Knowing that the system is in equilibrium, determine the magnitudes Tc and Td.
The triangular block shown in Fig. P-010 is subjected to the loads P = 1600 lb and F = 600 lb. If AB = 8 in. and BC = 6 in., resolve each load into components normal and tangential to AC.
ABCD is a rectangle with AB and AD of lengths 2a and a respectively. Forces of magnitudes 2 N, 3 N and 3√5 act along AB, AD and AC respectively, in the directions indicated by the order of the letters. Find the force which would need to be applied to A to maintain equilibrium
Derive an expression for the magnitude of the couple M required to maintain the equilibrium of the linkage shown.
An electric wire having a mass of 0.5 kg/m along the horizontal is suspended between supports of the same elevation which is 50m apart. If the maximum tension in the wire is 800N, find a. the minimum tensionb. the sagc. the length cable ANS.a. 790.17Nb. 1.98mc. 50.2m
A 1550−kg automobile has a wheel base (the didtance between the axies) of 2.90 m. The automobile's center of mass is on the centerline at a point 1.10 m behind the front axle. Find the force exerted by the ground on each wheel. each front wheel_____kN each rear wheei_______kN
Two forces of magnitude TA= 7607 lb and TB= 14617 lb are applied as shown to a welded connection. Knowing that the connection is in equilibrium and angle X is 48°, determine the magnitude of TC (lb).
A 12.6 inches long key is to be used on a 210 hp, 1200 rpm, slip ring induction motor. The key is 1 in wide and has a depth of 3/4 in. The shaft diameter is 3 7/8 inches. The maximum running torque is 200% of the full-load torque. 1. Determine the maximum compressive (crushing) stress of the key, in psi. 2. Determine the maximum direct shearing stress on the shaft, considering the effect of the keyway, in psi.
Determine the maximum force P the connection can support so that no slipping occurs between the plates. There are four bolts used for the connection and each is tightened so that it is subjected to a tension of 4 kN. The coefficient of static friction between the plates is μs = 0.4.
Determine the magnitude of Q if the particle is in equilibrium and if θ =35.5°, P = 325 , a=4, and b=17.
A vertical spring with constant k = 5 N/m and damping constant β = 6 kg/s has one end fixed to a wall, and a mass of 98 kg at the other end. Being in the position of equilibrium, the mass is propelled downward with a speed of 4 m/s. Suppose that on the system an external force acts in newtons given by f(t) = 8e^ −t What is the diferential equation and conditions that allow to fink the position of the spring as function of the time t, with t in seconds Determine a diferential equation of the position of the mass at any time “t”, with t in seconds