The hoist shown is used in a machine shop to position heavy workpieces in a lathe. If the cable between pulleys A and B can support a force of 305 lb, all other cables can support a force of 460 lb, and bar CE can support a compressive force of 615 lb, determine the largest weight W that may be lifted. D 5 12 C B E 7 24 W

The hoist shown is used in a machine shop to position heavy workpieces in a lathe. If the cable between pulleys A and B can support a force of 305 lb, all other cables can support a force of 460 lb, and bar CE can support a compressive force of 615 lb, determine the largest weight W that may be lifted. D 5 12 C B E 7 24 W

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A supporting rope is loaded with a line load q(x) = q0 between points A and B. The rope shall be stretched such that the slope of the rope at point A is zero. If l (small letter L) = 10 m and h = 2.3 m. Determine the (A) horizontal tensile force and (B) the maximum force in the rope. q0 = (kN/m) 12.213
A concrete cube 60 cm on each edge (sp. gr. 2.40) rests on the bottom of a tank in which sea water stands to a depth of 5 m. The bottom edges of the block and sealed off so that no water is admitted under the block. Find the vertical pull required to lift the block. Note: The answer should be 13.76 kN.
Determine the resultant of the three forces acting on the pulley shown
A transmission tower is held by three guy wires anchored by bolts at B, C, and D. If the tension in wire AB is 525 lb, determine the components of the force exerted by the wire on the bolt at B.
Given a 2.0meter Wide Flange steel compression member with A=4832mm2, Ix=88951759mm4 and Iy=3223498mm4 with Fy = 345MPa. Calculate the allowable strength in KN if both ends are hinged or pinned. Express your answer in 2 decimal places.
Given a 1.6meter Wide Flange steel compression member with A=4700mm2, Ix=84283141mm4 and Iy=3587323mm4 with Fy = 345MPa. Calculate the design strength in KN if both ends are hinged or pinned. Express your answer in 2 decimal places.
4. A torque of 9.5 kN is to be carried by a flanged bolt coupling that consists of eight 12 mm diameter steel bolts on a circle of diameter 300 mm and six 12 mm diameter steel bolts on a circle of 250 mm. Determine the shearing stress in the bolts.
Can you also find, 3. The tension in the rope 4. The magnitude of the force one ladder exerts on the other at point A 5. If 800N painter stands at point A find the tension in the horizantol rope
The 4-lb pulley has a diameter of 1 ft and the axle has a diameter of 1 in. If the coefficient of kinetic friction between the axle and the pulley is μk = 0.20, determine the vertical force P on the rope required to lift the 20-lb block at constant velocity.
Set P1P1P_1 = 30 kNkN and P2P2P_2 = 16 kNkN in (Figure 1). Figure 1 of 1The figure shows a truss consisting of two 2-meter long horizontal members, a 1.5 meter-long vertical member, and an inclined member. Pins C and B are located exactly above pins D and A, respectively. Members BC and AD are horizontal. The pin at B is fixed to a vertical surface to the right of it. The pin at A is fixed to the same vertical surface 1.5 meters below B. Member CD is vertical and member BD is inclined. Load P 1 is applied at C and it is directed vertically downward. Load P 2 is applied at D and it is directed horizontally to the right. Part A Determine the force in member ADAD, and state if the member is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. View Available Hint(s) FADFAD =…
Determine the reactions and draw the shear and moment diagram of the indeterminate beam given below using Consistent Deformation Method. Consider the support reaction at point C to be the redundant. 50 k 50 k -8 tt 8n 8 it 21 Upload Choose a File
A 50m steel tape weighs 0.035kg/m is constantlysupported at mid-length and at its end points and isused to measure a line AB with a steady pull of6.5kg. If the measured line AB is 1268.256m Determine the correct length of AB Determine the total sag correction for the whole length measured. Determine the correction due to sag for the whole tape length.