The 30-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E = 200 GPa. (Figure 1) Determine the displacement of end C with respect to the fixed support at A. Express your answer to three significant figures and include the appropriate units. ốc = Value Units Submit My Answers Give Up Provide Feedback Continue Figure 1 : of 1 > 600 mm 400 mm 50 kN 40 kN A В 50 kN

The 30-mm-diameter A-36 steel rod is subjected to the axial forces shown. Take E = 200 GPa. (Figure 1) Determine the displacement of end C with respect to the fixed support at A. Express your answer to three significant figures and include the appropriate units. ốc = Value Units Submit My Answers Give Up Provide Feedback Continue Figure 1 : of 1 > 600 mm 400 mm 50 kN 40 kN A В 50 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A uniform bar AB of weight W 5 25 N is supported by two springs, as shown in the figure. The spring on the left has a stiffness k1 5 300 N/m and nat- ural length L1 5 250 mm. The corresponding quanti- ties for the spring on the right are k2 5 400 N/m and L2 5 200 mm. The distance between the springs is L 5 350 mm, and the spring on the right is suspended from a support that is a distance h 5 80 mm below the point of support for the spring on the left. Neglect the weight of the springs. (a) At what distance x from the left-hand spring (fig- ure part a) should a load P 5 18 N be placed in order to bring the bar to a horizontal position?
Compute the resultant of the three forces shown in the figure. a.) None of the Above b.) 315.28 N c.) 836.90 N d.) 894.32 N e.) 948.27 N
A = 3 B = 4 C = 1 D = 0 kindly answer the magnitude and if possible the forces
Answer is 1,022.80. Show your solution. Forces F1 and F2 shown below act on the screw eye. If F1 = 501 lb, determine the magnitude of the resultant force (in lb) if it is directed vertically upward. Use F2 = 578 lb., α = 20°.
Please correct my understanding of this question. -In the equation of the moment at point A, there is a value, 36(11.5). I assume that is a force from the distributed load. -If you are finding the moment at point A, wouldn't you only need one value from the distributed load which is 27(10)? So my question is how do you get the value of 36 and 11.5, separately. And what is it for?
Need answer ASAP. Please be detailed and clear with your solution. IV. The corner of a floating body has a quarter cylinder AB having a length normal to the paper of 3 m. 8) Calculate the magnitude of the horizontal component of the force on AB in kN. *9) Calculate the magnitude of the vertical component of the force on AB in kN. *
Q.3 A uniform steel plate 360 mm square with a mass of 25 kg is suspended in the horizontal plane by the three vertical wires as shown. Calculate the tension in wire C. (round answer to one decimal places)
A beam is subjected to uniform force w as shown in the figure below, E of the entire section is 30000 kips/inch^2, I is 240 in^4, if point A is supported by 0.003 rad clockwise before assembly, and point B is supported at Subside 0.3 inches before assembly, try to calculate the reaction force of point A and point B.
Given the problem: The smooth disk shown in the figure is pinned at 'D' and has a weight of 24.6 lb. Neglecting the weights of the other members, determine the following: d.) Horizontal component at 'D' in lb. e.) Vertical component at 'D' in lb. *Round off final answer in 4 decimal places. Thank you.
18,1:The diameter of the AB bar shown in the figure is d=5 cm and the material it is made of is steel, with E=210 GPa and ϭF=250 MPa. Find the load P that the system can carry with a confidence of n=1.5 according to the AB bar. Answer: P= 39,16 kN
Consider the frame shown in figure. Suppose that P1 = 5.5 k and P2 = 11 k. Each column has the cross-sectional area indicated. Solve the problem using the cantilever method of analysis. Assume that the internal moment, shear, and normal force in the vertical beam are positive if they act as shown in (Figure 2). a) Determine (approximately) the normal force at A. NA = _____ k Submitted Answers ANSWER 1: Deduction: -3% NA = 4.973 k ANSWER 2: Deduction: -3% NA = 3.8254 k ANSWER 3: Deduction: -3% NA = 5.933 k
In the figure below, A, B, and C are all pin-connected, while D and E are fixed. With x = 6.5 , what is the vertical support reaction (in kips or k units) at A? Approximate final answers up to two decimal places.