The hydraulic conductivity of a soil sample (3.4 x 10-4 cm/s) has been determined via a permeability test. The water temperature was 28°C at the time of experiment. What is the hydraulic conductivity of the sample at the standard temperature of 20°C?

The hydraulic conductivity of a soil sample (3.4 x 10-4 cm/s) has been determined via a permeability test. The water temperature was 28°C at the time of experiment. What is the hydraulic conductivity of the sample at the standard temperature of 20°C?

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.6P

See similar textbooks

Related questions

Q: For a falling-head permeability test, the following values are given: · Length of specimen…

Q: A falling-head permeability test was carried out on a clay soil of diameter 100 mm and length 150…

A: We are required to calculate the hydraulic conductivity of clay.

Q: 6. The following data are for a falling-head permeability test: • Length of the soil sample = 140mm…

A: Hydraulic conductivity for falling head permeability test, k =aLAtlnh1h2 -----(1) where a = Area of…

Q: The hydraulic conductivity of a sand at a void ratio of 0.750 is 0.047 cm/s. Estimate the…

A: Given data: k0.75=0.047 cm/se1=0.750e2=0.450

Q: In a constant-head permeability test, a sample of soil 12 cm long and 6 cm in diameter discharged…

A: Given data Volume (V) = 1.5 × 10-3 m3 Time (t) = 10 min

Q: The hydraulic conductivity of a soil sample is 0.01 cm/sec at void ratio of 0.8. What will be the…

A: Given: First void ratio, e1 = 0.8 Hydraulic conductivity at first void ratio, K1 = 0.01 cm/s Second…

Q: From the constant head permeability test arrangement shown, the following values are given: Void…

Q: A fine-grained (silty-clay) soil is required for the core of a rockfill dam. The permeability tests…

A: Given: The diameter of the specimen is 8 cm. The length (L) is 15 cm. The below table shows the test…

Q: The results of a constant-head permeability test for a fine sand sample having a diameter of 150 mm…

A: We know that from constant head permeability test…

Q: 1. A 30cm long field sample is tested in a falling head permeameter with a 10 cm diameter cylinder.…

A: Given data : Diameter of tube (d)=10 mmDiameter of cylinder (D)=10 cmLength of sample (L)=30 cmHead…

Q: For a falling head laboratory test, the following are the given values: • Length of soil specimen =…

A: A) Hydraulic conductivity(K): K=2.303aLAtlog(h1h2)K=2.30342×2101050×3.5log523297K=1.358 mm/min

Q: falling head hydraulic conductivity test is performed on a sample of soil. The standpipe. having a…

A: Stand pipe diameter = 0.35cm Area = 0.0961cm2 Time taken = 80 sec H1 = 90cm H2 = 70 cm Length =…

Q: 3.Two cylindrical soil specimens (A and B) are subjected to a modified constant head test as shown…

A: when specimen are perpendicular, the discharge flow is same for them.

Q: A constant-head test was conducted on a sample of soil 15 cm long and 60 cm2 in cross-sectional…

A: 1. The discharge in the soil is given by,

Q: constant head permeability test was carried out on a sample of sand. The diameter and the length of…

A: We have formula for constant head test asQ=KiAVt=KhLAV=volumet=timeK=Hydraulic…

Q: constant

Q: A glass cylinder 5 cm internal diameter and with a screen at the bottom was used as a falling head…

Q: Situation 2 - For a constant laboratory permeability test on a fine sand, the following data are…

Q: Sketch the figure and determine coefficient of permeability (k) in mm/min using constant head…

A: given data: Water flows horizontally The height of the reservoir supply source is h=2 m above the…

Q: The permeability test must be carried out on a soil sample 15 cm long and 8 cm in diameter using the…

A: Constant and variable head permeameters are used for the measurement of permeability of soils.

Q: Determine the hydraulic conductivity of Soil A using the data obtained from the constant head test…

A: Given data for calculation of hydraulic conductive both constant head permeability test and falling…

Q: A sample of sand 5 cm in diameter and 15 cm long, was prepared at a porosity of 60% in a…

Q: For a falling-head permeability test, the following values are given: Length of specimen = 200 mm…

A: A falling head permeability test data is given and it has been asked to determine hydraulic…

Q: A constant-head test was conducted on a sample of soil 15 cm long and 60 cm^2 in cross-sectional…

Q: A constant-head test was conducted on a sample of soil 15 cm long and 60 cm2 in cross-sectional…

Q: A falling head hydraulic conductivity test is performed on a sample of soil. The following values…

A: To find coefficient of permeability and flow rate

Q: The following data are for a falling-head permeability test: Length of the soil sample = 140 mm…

A: Given data Length Diameter Area Time

Q: The permeameter in a permeability test setup involves a sample 200mm diameter and a length of 30mm.…

A: Given data: Volume of water collected: V= 450 m3 Time (t)= 4 minutes. Length of sample(L)=30 mm…

Q: For a falling head permeability test, these value are given:  Length of the soil specimen = 200 mm…

A: Given, Length of the soil specimen, L= 200 mmArea of the soil specimen, A= 1000 mm2Area of the…

Q: Question 33 A laboratory apparatus maintains a constant head in both the upper and lower reservoirs.…

A: Permeability of soil : The ability of soil to enable water to flow through it is referred to as…

Q: The following data are for a falling-head permeability test: Length of the soil sample = 140 mm…

Q: A sample coarse grained soil is 60mm. In diameter and 150mm long was tested in a constant-head…

A: To Determine a) temperature correction factor b) corrected coefficient of permeability C)…

Q: In a constant-head permeability test, a 60 cm3 of water was collected in 25 seconds with a head…

A: V=60cm3 t=25sec L=12cm D=8cm

Q: For a variable head permeability test, these values are given: • Length of the soil specimen 200 mm…

A: Given data: Length of soil specimen (L) = 200 mm Area of the specimen (A) = 1000 mm2 Area of stand…

Q: Length of soil sample for constant head permeability test is 30 cm, Area of specimen is 177cm)…

A: To find the hydraulic conductivity (K) -

Q: A falling head hydraulic conductivity test is performed on a sample of soil. The standpipe having a…

A: Falling head permeability test sample data and reading have been given and it has been asked to…

Q: The figure shows a soil in a tube with two cross sectional area: Au = 14 cm and A, 7 cm. Water is…

A: Given Hydraulic conductivity ,k = 1.2 ×10-5 m/sec

Q: Question 2 * The permeameter in a permeability test setup involves a soil sample 200 mm diameter and…

Q: In a falling head permeability test on a soil sample of length L1, the head of water in the stand…

Q: In a falling-head permeability test the following the apparatus was measured: Internal diameter of…

A: Falling head permeability test used to- -determine the…

Q: A constant-head test was conducted on a sample of soil 15 cm long and 60 cm2 in cross-sectional…

A: Length of sample (L) = 15 cm. Area of cross-section (A) = 60 cm2 Head difference (h) = 24 cm Volume…

Q: A constant-head permeability test is performed, and the information below indicates the test…

A: Given Data- Height of reservoir supply source = 2 m = 2000 mm Soil sample length, L = 200 mm…

Q: A permeability test was run on a soil sample with 8cm in radius and 10cm long. The level of water at…

Q: A constant-head permeability test is performed in a laboratory where the soil sample is 25 cm in…

Q: Read the question carefully and give me right solution. Provide detailed solution with clear…

Q: For a falling-head permeability test, the following values are given: • Length of specimen 8 in. •…

A: Area of standpipe (a)=0.06in2 Area of soil specimen (A)=1.6 in2 t=180sec

Q: In using a permeameter, it is sometimes convenient to make a “falling -head” test. The horizontal…

A: t=4hr To find hydraulic conductivity

Q: * The permeameter in a perrneability test setup involves a soil sample 200 mm diameter and a length…

Q: A falling head hydraulic conductivity test is performed on a sample of soil. The standpipe having a…

Q: A balloon-type apparatus is used to determine an in-place unit weight for a soil (field density…

Concept explainers

Laboratory Determination of Hydraulic Conductivity

Hydraulic conductivity is the measure of flowability of water inside the soil in the presence of a hydraulic gradient. The hydraulic gradient is defined as the difference in the water heads in the soil, which induces a water motion. In simple terms, a hydraulic gradient is the presence of a potential that induces a flow of water.

Question

The hydraulic conductivity of a soil sample (3.4 x 10^-4 cm/s) has been determined via a permeability test. The water temperature was 28°C at the time of experiment. What is the hydraulic conductivity of the sample at the standard temperature of 20°C?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Laboratory determination of hydraulic conductivity

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

In a constant-head permeability test, a sample of soil 12 cm long and 6 cm in diameter discharged 1.5 x 10^(-3) m^3 of water in 10 minutes. The head difference in two piezometers A and B located at 1 cm and 11 cm, respectively, from the bottom of the sample is 2 cm. Determine the hydraulic conductivity of the soil. What is the soil type tested?
The hydraulic conductivity of a soil sample is 0.01 cm/sec at void ratio of 0.8. What will be the hydraulic conductivity of the same sample at void ratio of 1.
For a decreasing load permeability test, the following are given values: - Sample length: 200 mm - Soil sample area: 1000 mm² - Piezometer area: 40 mm² - Load difference at instant t = 0: 500 mm - Load difference at instant t = 180 s: 300 mm Determine the hydraulic conductivity of the soil in cm/s.
For a variable head permeability test, these values are given:• Length of the soil specimen 200 mm• Area of the soil specimen 1000 mm2• Area of the standpipe 40 mm2• Head difference at time t 0 is 500 mm• Head difference at time t 3 min is 300 mma. Determine the hydraulic conductivity of the soil in cm/sec.b. What was the head difference at time t 100 sec?
For a falling-head permeability test, the following values are given: · Length of specimen = 250 mm. · Area of soil specimen = 1200 mm2. · Area of standpipe = 50 mm2. · Head difference at time t = 0 = 600 mm. · Head difference at time t = 200 sec = 300 mm. Determine the hydraulic conductivity of the soil in cm/sec.
In a constant-head permeability test, a 60 cm3 of water was collected in 25 seconds with a head difference of “H” cm in a soil sample that has a diameter of 8 cm and length of 12 cm. Calculate the hydraulic conductivity. If the sample has a porosity of 60%, determine the average velocity and seepage velocity. Estimate the coefficient of permeability of a soil similar to the sample with a porosity of 45% from the results of this test.
A fine-grained (silty-clay) soil is required for the core of a rockfill dam. The permeability tests are performed on two types of soil. The diameter (D) of the specimen was 8 cm, length (L) between the measuring points was 15 cm. the following table shows the recorded data during the test for both the soils. Soil A B Head difference, h (cm) 12 15 Volume of water, V (cm3) 10 8 Time, t (sec) 300 350 Compute the hydraulic conductivity (k) by applying Darcy’s Law and select the best soil. Give reasons for the answer.
The following data are for a falling-head permeability test:• Length of the soil sample = 140 mm• Diameter of soil sample = 70 mm• Area of the standpipe = 19.6 mm2• At time t = 0, head difference = 500 mm• At time t = 7 min, head difference = 350 mma. Determine the hydraulic conductivity of the soil (cm/sec)b. What was the head difference at t = 5 min?
The results of a constant-head permeability test for a fine sand sample having a diameter of 150 mm and a length of 300 mm are as follows: constant head difference = 500 mm, water collected in 5 min = 350 cm3, void ratio of sand = 0.61. Determine the hydraulic conductivity.
For a constant laboratory permeability test on a fine sand, the following data are given: Length of specimen: 16 cm. Diameter of specimen: 96 mm. Constant head difference: 50 cm. Volume of water collected in 4 min.: 420 cc Void ratio of the soil specimen: 0.55 Determine the hydraulic conductivity of soil in m/min.
The figure below is a constant-head permeability test device. The cross-sectional area of the sample is 120 cm2. After 10 seconds, the volume of water flowing through the soil sample is 150 cm3. What is the coefficient of permeability of the soil sample? What is the hydraulic gradient and seepage force of the seepage flow?
For a falling-head permeability test, the following values are given:• Length of specimen 8 in.• Area of soil specimen 1.6 in.2• Area of standpipe 0.06 in.2• Head difference at time t 0 20 in.• Head difference at time t 180 sec 12 in.Determine the hydraulic conductivity of the soil in in./sec