The input of a transmission line with Z. = 300 ohms is connected in parallel with the input of another transmission with 200-ohm characteristic impedance. Each line is terminated with a load that is equal to its characteristic impedance. The inputs of the two lines are connected to a third transmission line which supplies power to the first two lines. Find the Z of the third line such that there will be no reflected signal on the third line.

The input of a transmission line with Z. = 300 ohms is connected in parallel with the input of another transmission with 200-ohm characteristic impedance. Each line is terminated with a load that is equal to its characteristic impedance. The inputs of the two lines are connected to a third transmission line which supplies power to the first two lines. Find the Z of the third line such that there will be no reflected signal on the third line.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.36P

See similar textbooks

Similar questions

A small manufacturing plant is located 2 km down a transmission line, which has a series reactance of 0.5/km. The line resistance is negligible. The line voltage at the plant is 4800V(rms). and the plant consumes 120kW at 0.85 power factor lagging. Determine the voltage and power factor at the sending end of the transmission line by using (a) a complex power approach and (b) a circuit analysis approach.
A distortionless transmission line has a resistance per unit length of 0.5 ohm/m. If the characteristic impedance of the line is 50 ohm, them what will be the attenuation constant of the line in Neper (Np)/m?
A 105MHz, 90 v peak signal is incident on a 50-ohm transmission line. The line is 125m long and is terminated in 300-ohm load. What is the SWR for this situation? Find the reflection coefficient.
Given a telephone transmission line of 100 mile long has Z,=685-j92Q, 0a=0.00497 neper/mile and f=0.0352 rad/mile work at 1000Hz. If Z=2000Q and Eg=10Vrms with Z:=700Q, find the sending end impedance, voltage, current, and power.
A load has a reflection coefficient of 0.5 when referred to 50 Ω. The load is at the end of a line with a 50 Ω characteristic impedance.(a) If the line has an electrical length of 45 degrees, what is the reflection coefficient calculated at the input of the line?(b) What is the VSWR on the 50 Ω line?
A transmission line has a characteristic impedance of 100 ohm and a resistance of 0.2 ohm/m. If the line is distortion less, then what will be the attenuation constant associated with the line?
A transmission line has a characteristic impedance of 50 ohm and a line resistance of 0.1 ohm/m. If the line is distortionless, what will be the value of the attenuation constant of the line in Np/m?
A transmission line in air with characteristic impedance Z0=50 ohm is terminated with a load impedance ZL ohm. What is the propogation constant k of the transmission line (assuming a coaxial line) for a 100 MHz uniform plane wave? What is the equivalence impedance of Z(-l) at l=.75m when ZL=25-j200 ohm? Calculate the shunt admittance to be added at l=.75m so that the line matched.
What are (a) the values of the intercept points in the load line and (b) the slope of the load line given the circuit?
"A coaxial cable has a foam polyethylene insulator whose velocity factor is 0.7. If the inner diameter of the outer conductor is 4 times the diameter of the inner conductor, what is the characteristic impedance of the transmission line? Use four decimal places (if the answer is not an integer)."
Consider a transmission line with characteristic impedance (Zo) of value 50Ω, if the value of the measured VSWR is 2, determine the magnitude of the load (Zl ) connected to that line that generates such value.
At 3 GHz, a shorted parallel sideline will be used to match a 60 ohm transmission line to a load impedance of ZL = 30 - j60 ohms. What should be the length of the parallel lateral line, in mm? Calculate using the Smith diagram.