A lossless transmission line with characteristic impedance of Z0 = 1000 and length I = 52cm was terminated with a load of ZyF 30 + j50n. Based on the given, a) Find the reflection coefficient at the load and the standing wave ratio of the voltage on the line (GDDO). B) Find the impedance and admittance at the line input. (For f = 750MHZ) c) For f = 750MHZ, find the impedance and admittance values 2cm away from the load. (2 = 10 will be accepted.)

A lossless transmission line with characteristic impedance of Z0 = 1000 and length I = 52cm was terminated with a load of ZyF 30 + j50n. Based on the given, a) Find the reflection coefficient at the load and the standing wave ratio of the voltage on the line (GDDO). B) Find the impedance and admittance at the line input. (For f = 750MHZ) c) For f = 750MHZ, find the impedance and admittance values 2cm away from the load. (2 = 10 will be accepted.)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter13: Transmission Lines: Transient Operation

Section: Chapter Questions

Problem 13.14P

See similar textbooks

Similar questions

A three-phase power of 460 MW is transmitted to a substation located 500 km from the source of power. With VS=1. per unit, VR=0.9 per unit, =5000 km, Zc=500, and =36.87, determine a nominal voltage level for the lossless transmission line based on Eq. (5.4.29) of the text. Using this result, find the theoretical three-phase maximum power that can be transferred by the lossless transmission line.
A single-phase overhead transmission line consists of two solid aluminum conductors having a radius of 3 cm with a spacing 3.5 m between centers. (a) Determine the total line inductance in mH/m. (b) Given the operating frequency to be 60 Hz, find the total inductive reactance of the line in /km and in/mi. (c) If the spacing is doubled to 7 m, how does the reactance change?
A lossless transmission line has 100 ? characteristic impedance. The line is terminated in a load impedance of 70-j100 ?. The maximum voltage measured on the line is 200V. Find;1. The minimum current and minimum voltage on the line2. Explain how location of voltage maximum can be determined by using load reflection coefficient from the forward and backward wave.3. Using load reflection coefficient in ii., calculate the distance from the load that produce the maximum voltage and current.
. A 70 cm long lossless transmission line with characteristics impedance of 50 Ω operating at 5Mhz is terminated with a load of ?? = (65+j80) Ω. If the velocity is 0.8 times the velocity of light, then calculate (a) The reflection co-efficient, also verify the value using the given smith chart. (b) Compute the input impedance using the transmission line input impedance equation 50 Ω line is terminated with an impedance of ??= (90 – j120) Ω. Design a shortcircuited single stub matching circuit using Smith chart that is provided
1. What is the necessary condition for matching transmission lines? In addition, what is a micro strip line? 2. For a distortion less line α = 0.02dB/m, Z0 (R0) = 60Ω and C = 0.2nF/m. Find the resistance and velocity of wave propagation. [Do not forget the units.] 3. For a finite lossless transmission line with open-circuit termination, sketch Xio vs l. Indicate where the sketch is inductive and capacitive.
A lossless transmission with characteristic impedance of ?0 = 100Ω and length = 52cmThe line was terminated with a load of ?? = 30 + ?50Ω. According to what is given, a) The reflection coefficient in the load and the voltage standing wave ratio on the line (GDDO)Find out.b) Find the impedance and admittance at the line input. (for ? = 750???)c) For ? = 750???, the impedance and admittance values 2cm away from the load.(It will be assumed that = ?0.)
The capacitance per unit length and the characteristic impedance of a lossless Transmission line are C and Z0 respectively. Express the velocity of travelling wave on the transmission line in terms of the two given parameters above.
A lossless transmission line l = 0.3lambda in length was terminated with a complex load of ZL = 30-j20 ohms. Find the reflection constant on the load, the standing wave ratio on the line, the reflection constant on the input and the input impedance. Take the characteristic impedance for the line as 75 ohms.
The capacitance per unit length and the inductance per unit length for a lossless transmission line are 0.1 F/m and 20 H/m respectively. What will be the characteristic impedance of the line?
Vk(t)= 9cos2π * 10^6(t) volt Voltage of a lossless transmission line fed by its source parameters, C= 0,01 μF/m, L= 0,02 mH/m line length d= 0,5 λ, load impedance ZL= 50 ohm (a)γ=? (b)Z0=? (c)Ve=? (d)Total voltage and current on the line write the equations in the complex space. (e)Voltage and current on the load Obtain the expression. (f)Time of reflected current wave Write the expression in the space and draw. lesson: electrical and electronical engineering
Q1) A 70 cm long lossless transmission line with characteristics impedance of 50 Ω operating at 5Mhz is terminated with a load of ?? = (65+j80) Ω. If the velocity is 0.8 times the velocity of light, then calculate (a) The reflection co-efficient, also verify the value using the given smith chart.(b) Compute the input impedance using the transmission line input impedance equation.
In a three-phase transmission line with a length of 150 km, a voltage of 250 kV and a frequency of 50 Hz, the diameter of the steel-cored aluminum conductors is 18 mm, the roughness coefficient of the conductors is 0.6, and the spacing between the conductors is 6 m. Since the average air temperature is 27˚ C and the air pressure is 762 mmHg along the line, find the corona voltage around the conductor and the total loss of the line according to the Peek formula.