Answered: The input power to a 3-phase load is…

The input power to a 3-phase load is measured as 11kw. If the line current and power factor of the load are 32 A and 0.7, then the value of line voltage is given by,?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.40P: A balanced three-phase 240-V source supplies a balanced three-phase Load. If the line current IA is...

See similar textbooks

Related questions

Q: An Alternator having three-phase, 3-wire ABC system supplying an effective line voltage of 120 V,…

Q: The input power to a 3-phase star connected load is measured as 8kW. If the line voltage and power…

A: Given: 3-phase star connected load having

Q: A load of 135 MW at a power factor of 0.9 lagging can be delivered by a 3-phase transmission line.…

A: The line current supplied to the load and the resistance per phase for a 3∅ transmission line are…

Q: A 4200-V, three-phase transmission line has an impedance of 4+j ohms per phase. If it supplies a…

Q: A B N° C-

Q: The currents flowing in the lines toward a balanced load connected in A are Ia 10020° A, I, =…

A: Given line currents are, Ia = 100∠0° AIb = 141.4∠225° AIc = 100∠90° A

Q: A balanced, positive-sequence, Y-connected voltage source with Eab = 480∠0o volts is applied to a…

A: In this question, A balanced, positive-sequence, Y-connected voltage source Eab = 480∠0o Volts.…

Q: The input power to a 3-phase load is measured as 17kW. If the line voltage and power factor of the…

A: The input power to a 3-phase load is measured as 17kW. the line voltage and power factor of the load…

Q: For an AC power distribution circuit, the line voltage is 480V and the line current is 53A. The…

Q: The input power to a 3-phase load is measured as 14kW. If the line voltage and line current to the…

A: Power of a 3-phase load is given by following relation P = 3 x VL x IL x cos∅Where, P = 3 phase…

Q: Discuss why: (a) All ac transmission and distribution system are 3 phase system. (b) The…

A: a) All ac transmission and distribution system are 3 phase system because in 3 phase system…

Q: Obtain the readings of wattmeter 1 and wattmeter 2 in a three-phase three-wire system having…

Q: For an AC power distribution circuit, the line voltage is 480V and the line current is 53A. The…

Q: A load of 135 MW at a power factor of 0.6 lagging can be delivered by a 3-phase transmission line.…

Q: The unbalanced four wire Y-connected load has balanced voltages of 415 V and the RYB-sequence. By…

Q: The input power to a 3-phase load is measured as 18kW. If the line current and power factor of the…

Q: Assuming ACB sequence, find the line and phase voltage if Vcn= 30<50 V.

Q: A load of 130 MW at a power factor of 0.85 lagging can be delivered by a 3-phase transmission line.…

Q: Q.18: For the circuit shown, let Z=Z2=Z3 =10275° and the line voltage be a balanced abc (tve)…

A: The complex power in an AC system is defined as the product of rms value of applied voltage and…

Q: Given ??? = 208 ∠ − 40° V in a three-phase ACB circuit, find the currents of the phasor line for a…

A: Given, a three-phase ACB circuit having Line voltage, VL = 208 ∠ − 40° V Active power, P = 10 kW…

Q: A three-phase balanced wye-wye system has a line voltage of 208 V ms. The line current is 6 A ms and…

A: Steps: Draw the per-phase model of the given circuit Find R using per phase power loss Find Z using…

Q: A load of 135 MW at a power factor of 0.65 lagging can be delivered by a 3-phase transmission line.…

A: Below are the answers calculated for the above given data

Q: A 3-phase electric source delivers 150MVA to a balanced load 140KV at a power factor of 87% lagging.…

A: ELECTRICAL NETWORK: When addressing a circuit problem or constructing a balanced circuit, the word…

Q: 2.21 The three-phase source line-to-neutral voltages are given by E= 10/0, E = 10/+240, and E =…

Q: For the balanced positive-sequence three-phase circuit below, given that Var-100410° V and Za=15455°…

Q: A Y-Y three-phase circuit is shown below. Solve for the following: Line current of phase b = ? A…

A: In this question, 3 phase balance source is supplied to the 3 phase unbalanced load. We need to…

Q: From the circuit shown below; Assume a phase voltage of Van = 120∠0 ° positive sequence, where the…

Q: 2.40 A balanced three-phase 240-V source supplies a balanced three-phase load. If the line current…

A: We will draw phasor diagram indicating phase voltage and phase current in load. From phasor we will…

Q: A balanced Y-connected load is connected to 3-phase transmission lines with line-to-line voltages…

A: Given values, Balanced Y-connected load with line-to-line voltages, VL= 21.5 kV Current in each…

Q: Example A three-phase, balanced delta-connected load of (4+j8) ohms is connected across a 400 V,…

Q: The total apparent power supplied in a balanced, three-phase Y-Δ system is 4800 VA. The line voltage…

A: the per phase apparent power, SP=ST3 =48003 =1600 VA Since connection is Y - delta…

Q: An Alternator having three-phase, 3-wire ABC system supplying an effective line voltage of 120 V,…

Q: Two balanced three-phase loads that are connected in parallel are fed by a three-phase line having a…

Q: A balanced delta-connected load has phase impedances of 4+j3 Ohms. It is connected to balanced…

Q: A load of 130 MW at a power factor of 0.6 lagging can be delivered by a 3-phase transmission line.…

A: 1_∅ power=3-∅ power3. Per phase voltage=line voltage3power losses=3×I2 R.

Q: Suppose the value of each impedance of a Y-connected three-phase load is 15+j12 ohm. The terminal…

A: Transmission line

Q: circuit shown, let Z,=604-30°Q, 1: For the Z2=24Z30°0 impedances, and the phase voltage be a…

Q: in As in Example 2.5, a balanced-Y-connected voltage source with Eab = 480/0° volts is applied to a…

A: Solution:Given dataEab=0°480VZL=85°1ΩVbaseLL=480 VZ△=40°30ΩSbase 3ϕ=10 kVAfrom the given…

Q: Q2) A 3-phase transmission line has an impedance of 1 + j2 /phase. If it supplies a 3-phase load of…

A: Power lost in a resistor = current 2× resistance. Sending end voltage =receiving end voltage ×…

Q: Consider the balanced three-phase circuit is given below. The voltage values indicated are rms…

Q: A set of balanced three-phase transmission lines with line-to-line voltages of 13 kV is connected to…

A: Given: For balanced 3-phase star-connected load, per-phase impedance Z=8+3j Ω=8.544∠20.55° Ω,…

Q: Q.1 (a) A balanced RYB-sequence Y-connected source with VRN = 24020° connected to a A-connected…

Q: Find the line current, power factor, a

Q: A load of 145 MW at a power factor of 0.9 lagging can be delivered by a 3-phase transmission line.…

A: The performance of a power system depends mainly on the performance of transmission lines in the…

Q: A load of 140 MW at a power factor of 0.8 lagging can be delivered by a 3-phase transmission line.…

A: single phase power=three phase power3. current=three phase power3×voltage×power factor. total…

Q: A balanced three-phase ∆- connected source has a line voltage 120 V. It is connected to a load via a…

Q: If the load is delta-connected with impedance per phase of Z=30-j40 ohm and V line = 440 V, predict…

A: The solution is given below

Q: (2) (z) Just to make sure as a preliminary question... if the base quantity is XB and the actual…

Q: 4. A three-phase three-wire system has a balance Y-connected load with a 75 2 resistance, 125 mH…

A: Since you have asked for multiple questions, then as per bartleby guidelines, I am solving the first…

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

100%

The input power to a 3-phase load is measured as 11kw. If the line current and power factor of the load are 32 A and 0.7, then the value of line voltage is given by,?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The input power to a 3-phase load is measured as 17kW. If the line voltage and power factor of the load are 400 V and 0.5, then the value of line current is given by
The input power to a 3-phase load is measured as 16kW. If the line voltage and power factor of the load are 418 V and 0.6, then the value of line current is Answer and unit
A Y-Y three-phase circuit is shown below. Solve for the following: Line current of phase b = ? A Average power delivered to the load = ? W
A load of 135 MW at a power factor of 0.6 lagging can be delivered by a 3-phase transmission line. The voltage at the receiving end is to be maintained at 57 kV and the loss in the transmission is 6.5% of the power delivered. (Consider the line to be a short transmission line) Find A) Single phase Power delivered B) Per phase voltage C) Current flowing through the transmission line D) 3 Phase Losses in the transmission line E) Per phase resistance of the transmission line
A load of 140 MW at a power factor of 0.6 lagging can be delivered by a 3-phase transmission line. The voltage at the receiving end is to be maintained at 33 kV and the loss in the transmission as 8 % of the power delivered. (Consider the line to be a short transmission line) Find: 1)Single phase Power delivered: 2)Per phase voltage: 3)Current flowing through the transmission line: 4) 3 Phase Losses in the transmission line: 5) Per phase resistance of the transmission line :
The input power to a 3-phase delta connected load is measured as 3.7KW. If the line voltage and line current to the load are 438.6V and 10.1A respectively, then the power factor of the system is
4-3. A balanced three-phase Y load has one phase voltage of ??? = 277 ∠ 450 V. If the phase sequence is ACB, find the line voltages VCA, VAB and VBC.
A load of 140 MW at a power factor of 0.8 lagging can be delivered by a 3-phase transmission line. The voltage at the receiving end is to be maintained at 54 KV and the loss in the transmission is 8 % of the power delivered. (Consider the line to be a short transmission line) Find Single phase Power delivered Per phase voltage Current flowing through the transmission line 3 Phase Losses in the transmission line Per phase resistance of the transmission line
30. A 30-Y-connected load is connected between three line terminals, R, Y, B, the impedances (in ohms) of the load being: (I + 2) between R and the star point. (2+3) between Y and the star point and (3+j4) between B and the star point. The phase sequence is RYB. If the line voltage is 400 V, calculate the voltage between R and the star point. [181 V]
A balanced, positive-sequence, Y-connected voltage source with Eab = 480∠0o volts is applied to abalanced-∆ load with Z∆ = 30 ∠40o Ω. The line impedance between the source and load is ZL = 1 ∠850 Ω.for each phase. Calculate the line currents, the ∆ -load currents, and the voltages at the load terminals.Recall that ZY = Z∆/3
A balanced three-phase 240-V source supplies a balanced three-phase Load. If the line current IA is measured to be 15 A and is in phase with the line-to-line voltage, VBC, find the per-phase load impedance if the load is (a) Y-connected, (b) -conneeted.
In the following 3-phase balanced system, calculate the line currents. Depends on the load voltage source is va(t)=100.cosωt. Phases b and c 120 degrees offset. Does the current flow a within delta link? Prove and calculate.