A three-phase balanced wye-wye system has a line voltage of 208 V ms. The line current is 6 A ms and the total real power absorbed by the load is 1800 W. Determine the load impedance per-phase, if the line impedance is negligible.

A three-phase balanced wye-wye system has a line voltage of 208 V ms. The line current is 6 A ms and the total real power absorbed by the load is 1800 W. Determine the load impedance per-phase, if the line impedance is negligible.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.51P: A three-phase line with an impedance of (0.2+j1.0)/ phase feeds three balanced three-phase loads...

See similar textbooks

Related questions

Q: A 3-phase, 6 Pole, 50 Hz, 400 V induction motor takes a line current of 40 A at 0.8p.f. and runs at…

Q: If no other measurements detect a problem during service-interrupting maintenance, what step should…

A: The service-interrupting maintenance are caused during, Service Outages Downtime Panned and…

Q: Find the Inverse Laplace Transform of the following functions s+12 18) F(s) =- Ans. f(t) =3–2e* s?…

Q: Four e.m.fs e1 = 100 sin ωt, e2 = 80 sin (ωt − π/6), e3 = 120 sin (ωt + π/4) and e4 = 100 sin (ωt −…

Q: 0.048L 0.2728 0.32 0.08503 9A 4.7 2.80A Radio 20. 4.20V(* Battery Wind Solar Panel Repeator…

A: A thevenins equivalent circuit is used for solving complicated circuits, by converting the voltage…

Q: A B R1 R3 R6 9 8 R2 4 R4 5 R7 7 R9

Q: 3. 16Ω 1:4 + 240/0° V rms -j24 2 Vo=? Complex power supplied by the source=?

Q: 6. Which of the following need(s) to be provided by the lessee in a dark fiber lease? A. WDM…

A: Dark fiber: An unused optical fiber that has been laid is called Dark fiber. It is called dark…

Q: 1. Consider the n-input logic gate shown below that operate with the following voltage thresholds:…

A: Logic gates: It is an electronic device that is used in making of a Boolean function. It is the…

Q: /v2 and VDD Consider thne linear source follower below. [VTH 100 M1 500 500 M2 If Ip2 = 2 mA, a.…

A: MOSFET refers to the metal oxide semiconductor field-effect transistor, it belongs to the FET…

Q: Write the Kirchhoff's voltage equations for the circuit shown in the Figure below and hence find…

A: given circuit

Q: Q1// Write the Kirchhoff's voltage equations for the circuit shown in the Figure below and hence…

A: given here a circuit and asked to write the kirchhoff's voltages equations. and asked to determine…

Q: the line frequency is 60 Hz, the output frequency of a center-tapped transformer full-wave rectifier…

Q: Q2 (a) Differentiate between convolution and correlation processes in the digital signal processing…

A: Convolution: It is a property to calculate the output of the system by convolving the impulse…

Q: 11.22 In a balanced three-phase wye-wye system, the source is an abc-sequence set of voltages. The…

A: In this question we need to find a input sequence of the line to neutral voltage

Q: Capacitances C1 = 265.26 µF C2 = 1.33 mF LI Resistance R1 = 30 ERI R2 = 80 230v 60HZ R2 Inductances…

Q: (b) Given a discrete signal, x[n] = { A, 2,3, 2, A} i) What is the value of A if autocorrelation of…

Q: Write the Kirchhoff's voltage equations for the circuit shown in the Figure below and hence find…

Q: A three phase system has line to line voltage Vab= 1500 Vrms with 30 degree angle with a why load.…

Q: 5.18. A small DC machine has an armature resistance of 4 ohms. Under no-load conditions when…

A: Solution

Q: In a three phase balanced A-A has abc an System, the source Sequence. The line and load Imprdances…

A: In this question, A balanced Delta Delta system is given with impedance and current in the load.…

Q: Find the Inverse Laplace Transform of the following functions 3s² – 2s – 1 (s – 3)(s² +1) 20) F(s)…

Q: A 4-pole, 3-phase, Y-connected induction motor is rated 60HZ, 208V . Its parameters are Rs 120m2, R,…

A: It is given that: f=60 HzVL=208 VRS=120 mΩ=120×10-3 ΩRr=290 mΩ=290×10-3 ΩXm=417 ΩXls=700 mΩ=700×10-3…

Q: detail of PLL application in AM receiver

A: The Phased-Locked Loop is abbreviated as PLL . The Terminologies considered for Amplitude-Modulated…

Q: Assume that r(t) and y(t) are both continuous-time aperiodic signals, and Fourier Transform of æ(t)…

Q: Capacitances C1 = 265.26 µF C2 = 1.33 mF Inductances Resistance R1 = 30 LI SRI R2 = 80 230v 60HZ L1…

Q: Given the following signal. a[n] = { ...,2 ,3 ,1,2,3,1,2,3,1,... } b[n] = {…

Q: 1. Design a current mirror having a current I = 19 mA with Vcc = 15V. %3D

A: Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: jBQ all + V, | 2/0° A -jAN () 3/45° A ?For the circuit shown above, what is the magnitude of the…

Q: Type of Transistor: ? Circuit J+ Input (vs): Terminal ? Output (vo): Terminal ? Type of Amplifier…

A: As per the guidelines of bartleyby i need to answer first three subparts only.So kindly repost other…

Q: simplify the Boolean function, F=B’(CD’+A) + C’D(A’+B)

A: To simplify ,F=B'(CD'+A)+C'D(A'+B)

Q: Determine the Power consumed by the load (Green) when it is connected to a supply voltage of 48Vdc…

Q: The mathematical description of the square wave with the added noise spike above is

Q: Example 8.14. A 132 kV line with 1:956 cm dia. conductors is built so that corona takes place if the…

Q: Xc HE a 120/0° mA R1 R2 XI ?For the circuit shown above, what is the magnitude of the Thevenin…

A: given circuit

Q: Simplify i29+i21+i

Q: 7x10 x 1020 x 1500 E, = 178.5 V %3D 60 Example 26.9. An 8-pole d.c. generator has 500 armature…

A: The solution is given below

Q: * three - phoge syctem hay line to line woltage Vab = 1500 Voms ith 30° angle with a %3D load.…

A: Solve the problem

Q: Question 1. (a) Explain the chemical energy conversion to electrical energy. (b) What is battery?…

A: The transformation of energy from forms given by nature to forms that can be used by humans. Over…

Q: In balance slope detection method if the signal has a high value of amplitude, how the interference…

Q: 43: Use nodal analysis to find the power supplied by the current sources. R2

Q: 2. In free space, let D = 8xyz*ā, + 6x²z*ā, + 16x²yz*ā, pC/m². a. Find the total electric flux…

Q: QUESTION 12: The differential amplifier shown in Figure P11.60 has a pair of pnp bipolars as input…

A: Differential amplifier: It is a differential amplifier. This amplifies the voltage difference of the…

Q: Hi I will definitely upvote if correct! Please find the VCc of the circuit when Ay is -200. Thank…

Q: The iron core in a transformer has the purpose of O decreasing the reluctance of the magnetic path…

Q: The electric field of a particular mode in a parallel-plate air waveguide with a plate separation

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: (а) A logic circuit shown in Figure Q.3 has a 4-bit input A and B, three 4-bit wide 2:1 muxes, a…

Q: SHOW COMPLETE SOUTION C2 Cs C8 C7 a=C2 -Ca - 4MF C4 = Cr =Co 2MF CT= C8 = 6AF %3D 1. CNTAL - ?

A: In this question we will find total capacitance and total charge and charge on C2.. Note:- as per…

Q: In a balanced three-phase system, the source has an abc-phase sequence and is connected in delta.…

Q: In a balanced three phase system, the wye with an abc-phase Source is abalanced squence and Vab=…

A: In this question, We need to determine the line current and phase current in the load. We know…

Question

i need the answer quickly

11.61 A three-phase balanced wye-wye system has a line
voltage of 208 V ms. The line current is 6 A ms and
the total real power absorbed by the load is 1800 W.
Determine the load impedance per-phase, if the line
impedance is negligible.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Three identical impedances of 10∠ − 15° Ω to a line voltage of 208 V in star connectedconnected to a balanced source. We accept all line and phase voltages and currents as Vca as reference.Calculate in the form (Assume positive order).
The total apparent power supplied in a balanced, three-phase Y-Δ system is 4800 VA. The line voltage is 240 V. If the line impedance is negligible and the power factor angle of the load is −50∘, determine the impedance of A balanced three-phase load absorbs 96 kVA at a lagging power factor of 0.8 when the line voltage at the terminals of the load is 480 V.the load.
A Δ-connected source supplies power to a Y-connected load in a three-phase balanced system. Given that the line impedance is 3 + j2 Ω per phase while the load impedance is 5 + j1 Ω per phase, what is the magnitude of the line current. Assume the source phase voltage Vab = 220 ∠0° V rms and what is the magnitude of the voltage in the load (5+j1) ohms.
A certain generating plant in manila has 40kV, three phase transmission line to supply a 12MVA load at 30kV and 0.8 power factor. Find the resistance and reactance of the line if the length of the transmission line is 4,000 meters and the efficiency is 88%.
A balanced three-phase source furnishes power to the following three loads:Load 1: 6 kVA at 0.83 pf laggingLoad 2: unknownLoad 3: 8 kW at 0.7071 pf leadingIf the line current is 84.6 A rms, the line voltage at the load is 208 V rms, and the combined load has a0.8 pf lagging, determine the unknown load.
For the single-phase power system below, find the transmission losses in Watts (assume that the transformers are ideal). Hint: Remember that loads can be represented by complex numbers in either rectangular or polar form.
A balanced three-phase source furnishes power to the following three loads:Load 1: 6 kVA at 0.83 power factor laggingLoad 2: unknownLoad 3: 8 kW at 0.7071 power factor leadingIf the line current is 84.6 A rms, the line voltage at the load is 208 V rms, and the combined loadhas a 0.8 power factor lagging, determine the unknown load.
A 12,470V, three-phase, three wire source supplies a balanced wye load having an impedance of 50 angle -30° ohms per phase. Find the magnitude of the rms line current.
An abc-phase-sequence three-phase balanced wye-connected source supplies a balanced delta-connected load. The impedance per phase of the delta load is 24+j6 Ω. If Vab=115/∠20° V rms, Find the phase current Iab and the line current Ia.
2. A load Z draws 12 kVA at a power factor of 0.856 lagging from a 120-Vrms sinusoidal source. Calculate: (a) the average and reactive powers delivered to the load, and (b) the peak current.
A three-phase, three-wire, 240 V ACB system supplies power to a wye-connected load with resistances and inductances of Za: 25 ohms, 15mH; Zb: 40 ohms, 10mH; Zc: 20 ohms, 18mH. Find the total average power delivered to the load if the line impedance is given by 2 ohms and 15mH.
Determine phase impedances of a wye-connected balanced three-phase load 20 kVA, 400 Vat PF=0.866 lag, This load is supplied through a cable having an impedance of1.2 + j 0.5 Ohm. Calculate the supply voltage.