The normal stress at point A is .768 The joint is subjected to the force system shown in thefigure below (Figure 1) where P₁ = 270 lb andP₂ = 480 lb . The member has a rectangular cross-sectional area of width 0.5 in. and thickness 1 in.Figure1 of 1B1 in.--BAP◄P₂1.5 in.a2 in.CorrectPart BDetermine the normal stress at point B.Express your answer to three significant figures and include appropriate units.μA?OB= .671ksiSubmit Previous Answers Request AnswerX Incorrect; Try Again; 4 attempts remaining

given data P1 = 270 lb P2 = 480 lb find the combined normal stress at point B.

The joint is subjected to the force system shown in the figure below (Figure 1) where P₁ = 270 lb and P2 = 480 lb. The member has a rectangular cross- sectional area of width 0.5 in. and thickness 1 in.. Figure 1 of 1 B 1 in- A P₂ 1.5 in. 2 in. Correct Part B Determine the normal stress at point B. Express your answer to three significant figures and include appropriate units. μÅ ? OB = .671 ksi Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining

The joint is subjected to the force system shown in the figure below (Figure 1) where P₁ = 270 lb and P2 = 480 lb. The member has a rectangular cross- sectional area of width 0.5 in. and thickness 1 in.. Figure 1 of 1 B 1 in- A P₂ 1.5 in. 2 in. Correct Part B Determine the normal stress at point B. Express your answer to three significant figures and include appropriate units. μÅ ? OB = .671 ksi Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the maximum normal stress in the bar. The diameter is 1.5cm.F1 = 7KN F2 = 6KN F3 = 2KN F1 = 9KN
The rod BD is made of material with G1= 124 GPa has a diameter 34 mm is bonded to the tube CA at point B, the tube made of material with G2=211 GPa has an outer diameter 73 mm and wall thickness of 10 mm. If T1=579 N.m and T2=1042 N.m, answer the following questions: The maximum shear stress of the rod BD is The maximum shear stress of the tube CA is The maximum shear stress of the assembly is The angle of twist between D and B is The angle of twist between C and A is The angle of twist at D is Your answer The angle of twist between C and B is Your answer The reaction at point A is
The cross-sectional area of bar ABCD is 600 mm2. Determine the maximum normal stress in the bar. Express your answer in MPa.
The two cylindrical rod segments are fixed to the rigid walls such that there is a gap of 0.01 in. between them when T1 = 60°F. Each rod has a diameter of 1.25 in. Determine the average normal stress in each rod if T2 = 400F, and also calculate the new length of the aluminum segment. Take aal = 13(10-6)>°F, Eal = 10(103) ksi, (sY)al = 40 ksi, acu = 9.4(10-6)>°F, (sY)cu = 50 ksi, and Ecu = 15(103) ksi
Determine the principal stresses at points A and B of the cylinder. Consider: L = 70 mm; d = 20 mm; F = 12 kN; P = 15 kN; T = 800 Nm.
Determine the safe wall thickness of a 50 inches steel tank with internal pressure of 8 Mpa. The ultimate stress is 296 Mpa. The factor of safety to use is 3. A. 2 in B. 3 in C. 5 in D. 4 in
1) A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The diameter of the pressure vessel is 450 mm, and it's length is 2.0 m. Determine the maximum internal pressure that can be applied if the longitudinal stress is limited to 140 MPa and the circumferential stress is limited to 60 MPa 2) A compound thin cylinder has a common diameter of 100 mm, and the inner cylinder has a thickness of 2,5 mm. The radial pressure between the two cylinders is 200 KPa and the difference between the two common diameters before shrinkage was 0,004305 mm. E=200 GPa Determine : A) Thickness of the outer cylinder B) Resultant hoop stresses in both cylinders if the compound cylinder is subjected to an internal pressure of 180 KPa
The rectangular bar has a width of w = 3.25 in. and a thickness of t = 2.00 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load P is applied. Assume a = 4 and b = 5. A) Determine the magnitude of load P. Express your answer in kips (rounded to the nearest hundredths.) B) Determine the shear stress on plane AB. Express your answer in ksi (rounded to the nearest tenths.)
A 5-mm thick hollow steel has an allowable stress limited to 200 MPa. Determine the inside and outside diameter of the tube if the force applied is 100 kN.Answers: ro _______________ rt__________________
mechanics of deformable bodies The cylindrical tank has an outer radius of 1.5m and a wall thickness of 25 mm. If the tank is pressurized to 1.5 MPa, determine the longitudinal stress.
Air pressure in the cylinder is increased by exerting forces P = 3 kN on the two pistons, each having a radius of 45 mm. The cylinder is shown in the figure below. If the cylinder has a wall thickness of 2 Mm, determine the circumferential stress in the wall of the cylinder. Express your answer to three significant figures and include appropriate units.
The rectangular bar has a width of w = 3.00 in. and a thickness of t = 2.00 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load P is applied. Assume a = 4 and b = 5.Determine(a) the magnitude of load P.(b) the shear stress on plane AB.(c) the maximum normal and shear stresses in the block at any possible orientation.