Answer the problem. Show the full, complete and clear solution. Please provide a free body diagram. The lap joint shown is fastened by five % inch-diameter rivets. The bearing stress inthe plates is limited to 15 ksi and the shearing stress in the rivets is 10 ksi. Assumethe applied load is equally distributed among the five rivets. The thickness of eachplate is ½ in. Calculate the load P based on each stress given. Determine themaximum safe load P that can be applied. Express the loads in kips.Elevation ViewPlan View

Answered: Image /qna-images/answer/12393e61-2c9e-4073-b675-25a34a40d67b.jpg

Answered: The lap joint shown is fastened by five…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rigid bar AB shown below is supported by a steel rod AC having a diameter of 20 mm, and a block. Ignore the weight of AB and AC, and the distributed load on AB is p = 4.0 KN/m. Determine the axial normal stress developed in AC: = ____ MPa. Calculate your answer to 1 decimal place.
Solve for the indentation diameter if the BHN of the material is 70 and a 500 kg of load is applied? Use indenter diameter 10mm.
As shown, three steel wires, each 28 mm2 in area, are used to lift a mass M. Their unstretched lengths are 19.99 m, 19.98 m, and 20 m. If M= 1,182 kg. what stress exists in the MIDDLE wire? Use E=215 Gpa. Answer must be in MPa.
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa Determine maximum load P for block shear
The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the frictionless pulley at D. Find the stress (in psi) in the cable if its diameter is d = 0.51 in and the weight of the bar is 5298 lb. Round off the final answer to three decimal places.
Given bar having cross-sectional area of 700mm^2 is subjected to axial loads at the positions indicated.
A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. If the maximum allowable stress for this hollow rod is 325 kN/mm2 , calculate the minimum thickness of the rod. Give your answer in millimetres (mm) and to 2 decimal places.
The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the frictionless pulley at D. Find the stress (in psi) in the cable if its diameter is d = 0.55 in and the weight of the bar is 5391 lb. Round off the final answer to 3 decimal places.
Need asap A round brass rod 30 mm in diameter and 200 mm long is subjected to a compressive force of 100 kN. If μ = 0.33 and E = 105 GPa. Determine the change in diameter. In mm. Thanks
The connection consists of a plate connected to another plate by four 22 mm diameter rivets. It carries a load P = 60 kN at a distance of 165 mm from the centroid of the rivet group. Determine the shear stress on each rivet due to force alone, in MPa. Determine the shear stress on each rivet due to torsion alone, in MPa. Determine the shear stress on the highly stressed rivet, in MPa
QUESTION 3: A steel rope with a diameter of 1 cm is subjected to a tensile load of "120" N. Calculate the stress on the rope in the unit "MPa".
A hollow metal tube with an inside diameter of 145 centimeters must carry a tensile load of 670 kilo newton. Determine the outside diameter of the tube, in meters, if the stress is limited to147 Mpa.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS