Answered: QUESTION 3: A steel rope with a…

QUESTION 3: A steel rope with a diameter of 1 cm is subjected to a tensile load of "120" N. Calculate the stress on the rope in the unit "MPa".

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.10.3P: A flat bar of width b and thickness t has a hole of diameter d drilled through it (see figure). The...

See similar textbooks

Related questions

Q: 1. Calculate the stress developed (in Pa) for the following structural members that are each…

A: Since you have asked multiple questions in a single request, we would be answering only the first…

Q: Two solid cylindrical rods support a load of P = 27 kN as shown. Rod (1) has a diameter of 17 mm,…

Q: Calculate the bearing stress and shear stress between the pin and each bracket of a clevis joint.…

Q: A thin cylindrical pipe with an inside diameter of 300 mm is 6 mm thick and fitted with end covers.…

Q: A steel bar has three axial loads applied as shown in Fig. Draw an axial force diagram for the bar.…

A: Firstly find the support reaction at A. Apply horizontal equilibrium of the system,

Q: 1. Three long parallel wires equal in length are supporting a rigid bar connected at their bottoms…

A: It is the conceptual numerical of mechanics of solid portion and used concept is axial deformation…

Q: 1.) A long flat steel bar 6 in. wide and 3/8 in. thick has a 2.5 in. diameter circular hole…

Q: A hanger rod is stressed to 0.9167 N/mm2 , when a tensile load of 18 N is acting on it as shown in…

Q: For the shown figure, determine the average normal stress (MPa) developed in rod BC if the load has…

Q: A small seat angle is used to support a beam with a reaction of 6,000 lbs. Two 1/2 inch diameter…

Q: Figure 5 displays a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than…

A: E=PA∆LL⇒EA∆LL=P

Q: An aluminum rod length of 1.0 m and cross-secrional area 0.0005 m2 is used to support a load of…

A: Calculated stress on the aluminum rod. length of 1.0 m and cross-secrional area 0.0005 m2 is used to…

Q: ny mm is the smallest allowable outer diameter of the washer

A: GIVEN :- Diameter of rod : d= 34mm washer inner diameter : di = 37.5 Allowable stress of rod : σ=…

Q: Problem 1.2. Find the minimum diameter of a steel wire, which is used to raise a load of 4000 N if…

A: Given :- P=4000 N Stress=95 MN/m2 D= diameter of wire in mm

Q: c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile…

Q: The structure shown in Figure 3.1 consists of bar BD and two rods, AD and CD. Assuming that the…

A: Draw the given diagram showing the axes and specifying B as the origin. From the figure, taking B…

Q: Question 3 A steel rod 20 mm in diameter passes centrally through a steel tube of 25 mm internal…

Q: Q2: A composite bar is made up two vertical rods of steel and copper each of length 2 m and diameter…

A: from the above figure given data is load is 15KN in the given question find out each load on the…

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have square…

Q: 5. A load of 5 kN is to be raised by means of a steel wire. Find the minimum diameter required, if…

A: Given data: F=5 kNσ=100 N/mm2 Need to determine the minimum required diameter of the wire.

Q: The stress in a wire of diameter 2 mm if a load of 100 gm is applied to a wire.

Q: The timber member has a cross-sectional area of 1750 mm? and its modulus of elasticity is 12 GPa.…

Q: QUESTION 3: A steel rope with a diameter of 1 cm is subjected to a tensile load of "60" N. Calculate…

Q: A steel rod having a length of 1m has a cross-sectional area of 100mm^2. if it is subjected to an…

Q: Rod of diameter 20 mm is loaded with 5kN tension force. What is the magnitude of stress in the rod?

A: Given, Diameter of rod = d = 20 mm Force applied to rod = F = 5 kN = 5000 N Cross-sectional area…

Q: A Portable Crane will be designed as shown in Figure which is able to withstand dynamic loads. The…

Q: For question 103A and 103B, the thin-walled cylindrical container shown below. Say p is the internal…

A: Internal pressure P=15 MPa Inside diameter d=20 mm Wall thickness t=10 mm Longitudinal stress in a…

Q: A rigid bar with negligible mass is pinned and attached to two vertical rods. If P = 50 kN, compute…

A: Given configuration: Free body diagram of rigid bar is drawn below. Let FC , FD be the internal…

Q: a cylindrical disk with diameter 40 mm and thickness 2 mm is compressed stress = applied…

A: As this is a simple question related to the strength of material subject. As stress formula is given…

Q: 1. A picce of wire 10-in long is tied vertically. The wire has a diameter of 0.1-in and is used to…

Q: Question 2 a) Figure Q2a shows a hollow tube of rectangular cross-section subjected to an axial…

Q: 1. Three vertical rods AB, CD, and EF supports a load of 36 kN. Each of the rods AB and CD has a 200…

A: When an external force is applied to any body the body gets deformed. This deformation is resisted…

Q: If a pipe with an inner diameter of 36 mm is subjected to an axial load of 5.20 x 105 N and the…

A: given data dia (d) = 36mm load = 5.20 * 105 N presure (P) = 5.20×105π4×0.0362 allowable stress = σ…

Q: 8000 lb 3000 lb 7000 lb 2000 lb 4' 5' 3' Fig. P-208 and P-209. up (73 208. An aluminum bar having a…

A: To find: The total deformation. Give: The Young's modulus is E=10×106 psi. The cross sectional area…

Q: 2. Shown in Figure below, is a section through a balcony. The total uniform load of 600 kN is…

A: Calculated load in each rod.

Q: A two spring is connected in parallel attached to a single load. The maximum allowable stress is…

A: Given that, Allowable stress, σ=200 MPa,Spring 1, d=33 mm,n=18,R=120 mm,Spring 2,d=30 mm,n=20,R=100…

Q: A cylindrical pressure vessel is fabricated from steel plating that has wall a thickness of 10 mm…

Q: 2 A hollow short cast iron column has outside and inside diameters of 250 mm and 150 mm…

Q: Calculate the largest weight W that can be attached to the two wires shown in Figure P-103. The…

Q: A hollow tube with thickness t = 1/4 in. is applied with a tensile load of 33 kips. Compute its…

A: Given data, Tensile load P= 33kips = 33000 lbs t= 1/4 in Tensile stress S= 12 ksi = 12000 lb/in²…

Q: A crane hook shown in figure below is made of 30 mm diameter steel rod. The distance between the…

A: To find: The load F so that the maximum stress in the rod is not exceed 40 Nmm2. Given: The diameter…

Q: Find the tensile stress in MPa in member AB shown in the figure. All connection bars have a square…

A: Calculate tension in AB for moment equilibrium about C T x 6 = 20 x 9.5 T = 31.6666 N

Q: A tractor weighing 80 kN was lifted by 3 cables as shown in the figure. Calculate the stress on the…

A: Given: W=Mg = 80 kN The given system will have four forces to be in equilibrium. The equilibrium…

Q: 3) A 0.5 inch diameter aluminum rod is used to support a decorative overhang. If the 7ft rod deforms…

A: NOTE:- As per our company guidelines we are supposed to answer only one question. Kindly repost…

Q: A bin weighing 15 kips is supported by 3 steel tension rods. Each rod has a diameter of 1 in.…

Q: If a bar is subject to a compressive force of 15 lb, and the area of the bar is 0.1 in^2 (square…

Q: 2.49. A bar of rectangular cross section 20 mm × 3 mm has a central hole of diameter 6 mm. Find the…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: Question 3 (a) One end of a wire of length L and diameter d is attached to a high ceiling. The wire…

Q: The structure supports force P=75 kN, as shown in Figure 6. The solid circular rod BD is made of…

Q: wire, but an extremely big block. So, compute the maximum load (in Newton) a round wire of this…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

QUESTION 3: A steel rope with a diameter of 1 cm is subjected to a tensile load of "120" N. Calculate the stress on the rope in the unit "MPa".

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A round bar of 10 mm diameter is made of aluminum alloy 7075-T6 (see figure). When the bar is stretched by axial forces P, its diameter decreases by 0.0 16 mm. Find the magnitude of the load P. Obtain the material properties from Appendix 1.
A suspender on a suspension bridge consist of a cable that passes over the main cable (see figure) and supports the bridge deck, which is Far below. The suspender is held in position by a metal tie that is prevented from sliding downward by clamps around the suspender cable. Let P represent the load in each part of the suspender cable, and let represent the angle of the suspender cable just above the tie. represent the allowable tensile stress in the metal tie. (a) Obtain a formula for the minimum required cross-sectional area of the lie. (b) Calculate the minimum area if P = 130 kN, = 75°, and allow=80 .
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
A flat bar of width b and thickness t has a hole of diameter d drilled through it (see figure). The hole may have any diameter that will fit within the bar. What is the maximum permissible tensile load Pmaxif the allowable tensile stress in the material is st?
A symmetrical framework consisting of three pin-connected bars is loaded by a force P (see figure). The angle between the inclined bars and the horizontal is a = 52°. The axial strain in the middle bar is measured as 0.036. Determine the tensile stress in the outer bars if they are constructed of a copper alloy having the following stress-strain relationship:
A tubular post of outer diameter d2is guyed by two cables fitted with turnbuckles (see figure). The cables are lightened by rotating the turnbuckles, producing tension in the cables and compression in the post. Both cables are lightened to a tensile force of 110 kN. The angle between the cables and the ground is 60° and the allowable compressive stress in the post is ?? c= 35 MPa. If the wall thickness of the post is 15 mm, what is the minimum permissible value of the outer diameter d2?
Rigid bar ACB is supported by an elastic circular strut DC having an outer diameter of 15 in. and inner diameter of 14.4 in. The strut is made of steel with a modulus elasticity of E = 29,000 ksi. Point load P = 5 kips is applied at B. Calculate the change in length of the circular strut DC. What is the vertical displacement of the rigid bar at point B?
A rope has a cross sectional area of 0.002m2 and is being used to lift a 5000N weight. What is the stress in the rope?
The stress in a wire of diameter 2 mm if a load of 100 gm is applied to a wire.
Q // If the value of the highest load we get from the tensile test of a wrought iron model with a circular . section is (52 kN) with an axial stress of ( 460 Mpa), calculate the diameter of the examined model