The large piston of a hydraulic lift had a cross-sectional area 60 times more than the small cross-sectional area. Determine the force F2. (Instruction: Type your answer without any unit. Type only the number) F1 = 20 N Small Piston, A1 Large Piston, Az F2

The large piston of a hydraulic lift had a cross-sectional area 60 times more than the small cross-sectional area. Determine the force F2. (Instruction: Type your answer without any unit. Type only the number) F1 = 20 N Small Piston, A1 Large Piston, Az F2

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter14: Fluid Mechanics

Section: Chapter Questions

Problem 14.8P: The small piston of a hydraulic lift (Fig. P14.8) has a cross-sectional area of 3.00 cm2, and its...

See similar textbooks

Similar questions

What force must be exerted on the master cylinder of a hydraulic lift to support the weight of a 2000-kg car (a large car) resting on the slave cylinder? The master cylinder has a 2.00-cm diameter and the slave has a 24.0-cm diameter.
The hydraulic system of a backhoe is used to lift a load as shown in Figure 11.45. (a) Calculate the force F the slave cylinder must exert to support the 400-kg load and the 150-kg brace and shovel. (b) What is the pressure in the hydraulic fluid if the slave cylinder is 2.50 cm in diameter? (c) What force would you have to exert on a lever with a mechanical advantage of 5.00 acting on a master cylinder 0.800 cm in diameter to create this pressure? Figure 11.45 Hydraulic and mechanical lever systems are used in heavy machinery such as this back hoe.
What force must exerted on the master cylinder of a hydraulic lift to support the weight of a 2000-kg car (a large car) resting on a second cylinder? The master cylinder has a 2.00-cm diameter and second cylinder has 24.0-cm diameter.
How much pressure is transmitted in the hydraulic system considered in Example 11.6? Express your answer in pascals and in atmospheres.
Oil having a density of 930 kg/m3 floats on water. A rectangular block of wood 4.00 cm high and with a density of 960 kg/m3 floats partly in the oil and partly in the water. The oil completely covers the block. How far below the interface between the two liquids is the bottom of the block?
Explain why the fluid reaches equal levels on either side of a manometer if both sides are open to the atmosphere, even if the tubes are of different diameters.
The greatest ocean depths on Earth are found in the Marianas Trench near the Philippines. Calculate the pressure due to ocean at bottom of this trench, given its depth is 11.0 km and assuming density of seawater is constant all way down.
A glucose solution being administered with an IV has a flow rate of 4.00 cm3/min. What will the new flow rate be if the glucose is replaced by whole blood having the same density but a viscosity 2.50 times that of glucose? All other factors remain constant.
Every few years, winds in Boulder, Colorado, attain sustained speeds of 43.0 m/s (about 100 mph) when jet steam descends during early spring. Approximately what is the force due to the Bernoulli equation on a roof having an area of 220m2? Typical air density in Boulder is 1.14kg/m3, and be corresponding atmospheric pressure is 8.89104 N/m2. (Bernoulli’s principal as stated in the text assumes laminar flow. Using the principle here produces only an approximate result, because there is significant turbulence.)
Calculate Reynolds numbers for flow of trough (a) a nozzle a radius of 0.250 cm and (b) a garden hose with a radius of 0.900 cm, when be nozzle is attached to hose. The flow rate through hose and nozzle is 0.500 L/s. Can flow in either possibly be laminar?
Is there a net force on a dam due to atmospheric pressure? Explain your answer.
Fluid originally flows through a tube at a rate of 100 cm3/s. To illustrate the sensitivity of flow rate to various factors, calculate be new flow rate for following changes with all other factors remaining the same as in original conditions. (a) Pressure difference increases by a factor of 1.50. (b) A new fluid wit 3.00 times greater viscosity is substituted. (c) The tube is replaced by one having 4.00 times the length. (d) Another tube used with a 0.100 times the original. (e) Yet another tube is substituted with a radius 0.100 times the original and half length, and pressure difference is increased by factor of 1.50.