The lead screw of a lathe has Acme threads of 60 mm outside diameter and 8 mm pitch. It supplies drive to a tool carriage which needs an axial force of 2000 N. A collar bearing with inner and outer radius as 30 mm and 60 mm respectively is provided. The coefficient of friction for the screw threads is 0.12 and for the collar it is 0.10. Find the torque required to drive the screw and the efficiency of the screw.

The lead screw of a lathe has Acme threads of 60 mm outside diameter and 8 mm pitch. It supplies drive to a tool carriage which needs an axial force of 2000 N. A collar bearing with inner and outer radius as 30 mm and 60 mm respectively is provided. The coefficient of friction for the screw threads is 0.12 and for the collar it is 0.10. Find the torque required to drive the screw and the efficiency of the screw.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.57P: The square-threaded screw with a pitch of 10 mm and a mean radius of 18 mm drives a gear that has a...

See similar textbooks

Similar questions

The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The cone clutch transmits the torque C through a conical friction surface with cone angle . The inner and outer radii of the friction surface are a and b, respectively. The left half of the clutch is keyed to the shaft, and the right half drives a machine (not shown) through a gear attached to its outer rim. Assuming uniform pressure on the friction surface, show that the maximum torque that can be transmitted by the clutch is
The clutch described in Prob. 7.75 is to transmit a torque of 120lbft when the total spring force exerted on the pressure plate is 75 lb. If Ri=4in., calculate the minimum acceptable value for RO. Assume that the clutch is new.
Solve Sample Problem 7.16 if the contact pressure under the polisher varies parabolically from p0 at r=0 to zero at r=R; that is, p=p0(1r2/R2).
A multiple vee-belt drive is required to transmit 4 kW. The smaller pulley has of the systemhas a diameter 150 mm and rotates at 200 rev/min. The grove angle is 40° and thecoefficient of friction between the belt and pulley is 0·3.(a) If the maximum tension in any one belt is limited to 800 N and the angle of lap is135°, determine the number of belts required. (b) Determine also, the initial pre-tension required in the belt.
The uniform bars shown are joined by a frictionless pin at their tops. Thecoefficient of friction between the bars and the floor is 0.30. What is the value of θ whenmotion spends?
The root diameter of a triple threaded power screw is 550 mm It has a pitch of 10 mm It is used to lift a load of 15 kN. The collar of the screw has an outside diameter of 100 mm and an inner diameter 60 mm Find the force applied at a radius of 950 mm if the coeffcient of friction for both threads and collar is 0.20.
The disc clutch has a pair of mating friction surfaces, with an outer diameter of 350 mm and an inner diameter of 250 mm. The average value of the coefficient of friction is 0.25, and the operating force is 5 kN. Find the torque capacity when the clutch is new, the maximum pressure and the torque capacity after a sufficiently long operating period.
In a thrust bearing, the external and the internal diamaters of the contacting surfaces are 320 mm and 200 mm respectively. The total axial load is 80 kN and the intensity of pressure is 350 kN/m2.The shaft rotates as 400 rpm. Taking the coefficient of friction as 0.06, calculate the power lost in overcoming the friction. Also, find the number of collars required for the bearing.
4.) A flat belt makes contact with an 16 in. diameter pulley through half its circumference. If the coefficient of friction is 0.45 , and a torque of300ft−bsis to be transmitted, calculate the belt tensions. (please type answer not write by hend)
Two pulleys, one 650 mm diameter and the other 400 mm diameter, on parallel shafts 1.5 m apart are connected by a flat belt. Find the length of the belt required and the angle of contact between the belt and each pulley. What power can be transmitted by the belt when the larger pulley rotates at 1200 rev/min, if the maximum permissible tension in the belt is 10 kN, and the coefficient of friction between the belt and pulley is 0.05? dont write handwritten solution.
The screw of the small presshas a mean diameter of 25 mm and has asingle square thread with a lead of 8 mm. Theflat thrust bearing at A is shown in theenlarged view and has surfaces which are wellworn. If the coefficient of friction for both thethreads and the bearing at A is 0.25, calculatethe design torque M on the hand wheelrequired (a) to produce a compressive force of4 kN and (b) to loosen the press from the 4-kNcompression.