The linkage for a hydraulic jack is shown. If the load on the jack is 2000 lb, determine the pressure acting on the fluid when the jack is in the position shown. All lettered points are pins. The piston at H has a cross-sectional area of A = 2 in?. Hint: First find the force F acting along link EH. The pressure in the fluid is p= F/A. | 2000 lb 2 in. -2 in. 30 in. 60° 5 in. H.

The linkage for a hydraulic jack is shown. If the load on the jack is 2000 lb, determine the pressure acting on the fluid when the jack is in the position shown. All lettered points are pins. The piston at H has a cross-sectional area of A = 2 in?. Hint: First find the force F acting along link EH. The pressure in the fluid is p= F/A. | 2000 lb 2 in. -2 in. 30 in. 60° 5 in. H.

Name: 3. The linkage for a hydraulic jack is shown. If the load on the jack
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 3. The linkage for a hydraulic jack is shown. If the load on the jack is 2000 lb, determine thepressure acting on the fluid when the jack is in the position shown. All lettered points arepins. The piston at H has a cross-sectional area of A = 2 in?.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.116P: Each of the three gates has a constant width 1: (perpendicular to the paper). Calculate the force P...

See similar textbooks

Similar questions

The weight of the cylindrical tank is negligible in comparison to the weight of water it contains (water weighs 62.4lb/ft3). The coefficient of static friction between the tank and the horizontal surface is s. (a) Assuming a full tank, find the smallest force P required to tip the tank, and the smallest s that would allow tipping to take place. (b) If the force P = 200 lb initiates tipping, determine the depth of water in the tank.
The high-pressure water cock is rigidly attached to the support at D. Neglecting the weights of the members, draw the FBD of the entire assembly and count the unknowns.
The center of gravity of the 850-N man is at G. If the man pulls on the rope with a 388-N force, determine the horizontal distance b between the man's feet and G.
Determine the force F required to pull up the 3.54m stopper from the drain of a sink if the depth of water is 10 in. Use =0.036lb/in.3 for water and neglect the weight of the chain.
The tank is fined with water. Determine the resultant force acting on the triangular plate A and the location of the center of pressure. Measured from the top of the tank. Solve the problem using the formula method
Plate AB has a width of 1.5 m and a radius of 3 m. Determine the horizontal and vertical components of reaction at the pin A and the vertical reaction at the smooth stop B due to the water pressure. Strictly using General Solution, and please show pressure diagram.
Determine the resultant force USING GENERAL SOLUTION of the oil exerts on the semicircular surface AB.The tank has a width of 3 m. Take liquid density as 900 kg/m3.*USE GENERAL SOLUTION AND SHOW PRESSURE DIAGRAM
Fluid Mechanic: The homogeneous timber AB as shown in the diagram is 0.15 m X 0.35 m in cross section. Determine the specific weight of the timber and thetension in the rope.
Find the horizontal pressure acting at the face of the damn at 20ft depth.
Find the total (resultant) pressure acting on the tail end of the container containing gasoline (S = 0.7) accelerating at 3m/sec² to the right.
Determine the pressure difference at A and B
A cubical tank of 2 m side contains oil of relative density 0.8 to t depth of 0.6 m and sea water of relative density 1.024 to a depth of 1 m. Calculate the pressure on the bottom of the tank and the total thrust on one side of the tank. Determine also the position of the center of pressure above the base. Ans. 14.8 kN/m2, 22.31 kN, 0.512m