A pipe set up is given as seen in the figure. The fluid is oil with a specific gravity of 850kg/m³. The pressure at the exit is atmospheric pressure. The diameter at theentrance is 6.4 cm and the diameter at the exit is 2.2 cm. The volume rate of flow isgiven as 0.0315 m³/s and thegage pressure at the entrance is 250 kPa. Ignore weightof the fluid and the pipe. Determine the x-component of the force applied at thebolts at section 1. Assume that the atmospheric pressure is 1013 mb.40°2

for solution refer below images.

/s and thegage pressure at the entrance is 250 kPa. Ignore weight of the fluid and the pipe. Determine the x-component of the force applied at the bolts at section 1. Assume that the atmospheric pressure is 1013 mb.

/s and thegage pressure at the entrance is 250 kPa. Ignore weight of the fluid and the pipe. Determine the x-component of the force applied at the bolts at section 1. Assume that the atmospheric pressure is 1013 mb.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Problem 3 - Nitrogen in the reservoir is at a temperature of 20°C and an absolute pressure of 300…

Q: Q2) Find the liner acceleration to the left that make the shape of the water in the tank as shown in…

A: Given S= 2m M= 3m R = 1.5m To find Linear acceleration to the left Pressure at point P

Q: Problem 2. Air is drawn into the 200-mm-diameter cylinder through the opening at A. If the piston is…

A: Given- Velocity of piston, (V)= 10 m/s Diameter of cylinder, (d) = 200 mm = 0.2 m Density of air…

Q: Find the resultant force which acts on the gate's submerged face if the gate is 4 m long. 5m 5m 60°…

Q: = Q2: As shown in figure (2), when the water jet of diameter 25mm and Vj 30 m/sec., determine the…

Q: *5-16. The level of mercury in the manometer has the reading shown. Determine the veloci- ty of the…

Q: Determine the inclination angle at point C for the water stream to reach a range of 10 m. Also…

Q: the mercury 2. Mercury is poured into the tube in the figure until occupies 375 mm of the tube's…

A: Consider the length of the mercury above the horizontal surface.x1 + x2 =375 mm - 160 mm x1 = 215…

Q: Determine the magnitude of the resultant force of the water acting on the circular glass plate that…

Q: horizontal plane; water enters from the west and leaves towards the north. Consider the atmospheric…

Q: Determine the difference in height h of the water column in the manometer if the flow of oil through…

A: Given Discharge, Q = 0.04 m3/s Density = 875 kg/m3 Find Difference in height, h

Q: Q2) Find the liner acceleration to the left that make the shape of the water in the tank as shown in…

Q: By applying a force F, a saline solution is ejected from the 10-mm-diameter syringe through a…

Q: What is the minimum Block mass (kg) that is required to open the gate A-B? The density of water is…

A: Density of water, ρw=1000 kg/m3 Density of the block, ρb=8000 kg/m3 Specific gravity of oil, sgo=0.9

Q: 1-Show that 0.646 Cf, Re =U If velocity profile is::

Q: (g) If the pressure at point B(3 m,2 m) is 600 kPa, determine the pressure at point C(1 m,3 m). Take…

A: Given Data: The coordinate of point B is (3,2). The coordinate of point C is (1,3). The pressure at…

Q: A 3-ft-diameter vertical cylindrical tank open to the atmosphere contains 1-ft-high water. The tank…

A: Given data: The initial height of water level is h0 = 1 ft. The diameter of the cylinder is d = 3…

Q: The total weight of the plunger and load is 30 kN, the plunger diameter is D=200 mm. Neglecting…

Q: shown below sucks air from the ambient and expels it as a jet at 1 m/s to the ambient. Determine the…

A: Given:

Q: he volume of the fluid inside the upright conical tank is 0.8 ft3. (a) Determine the needed volume…

A: Given:Volume of fluid inside the tank, Vi=0.8 ft3Mas of the fluid inside the tank, m=40 kg

Q: Water flows steadily and frictionless from the large open tank through the 3-in diameter pipe, and…

A: For the above FBD we have the Bernoullis equation asFor points between 1 and…

Q: *5-12. The jet airplane is flying in still air, A, at an altitude of 4 km. If the air flows past…

A: The density of air at 4 km above the sea level is The absolute velocity of the air over the wing at…

Q: QI: Determine the pressure in the pipeline if the atmospheric pressure is 80 kPa.

A: This problem is related to fluid mechanics. Fluid mechanics is the subject of mechanical engineering…

Q: 18. If the truck has a constant acceleration of 2 m/s, determine the water pressure at the bottom…

Q: if the velocity distribution of an oil over a plate is given by the relation, u=2/3y-y³ in which u…

Q: Determine the relationship between the air pressure in the tank and the maximum height to which the…

Q: 4- Determine the mass of air in a 2 m' tank if the air is at room temperature. 25 "C, and the…

A: Given data :- volume = 2 m^ 3 temperature = 25°C absolute pressure = 300kpa find the mass of air .

Q: E, Determine the tank

A: To find dimensions of tank (m)

Q: Problem 5: Water flows through the horizontal branching pipe (pipe 2 3) shown in Figure. If a…

A: Given Data Velocity at section 1 is: v1=6 m/s Velocity at section 2 is: v2=9 m/s Area at section 1…

Q: Show that the expression v = v0 + at is dimensionally correct, where v and v0 represent velocities,…

A: given data v = v0 + at

Q: Find the force components Fx and Fz of the hydrostatic force on the wetted surface of a cylindrical…

Q: Q3. (a) Determine the resulting hydrostatic force of water acting on the cylindrical wall of the…

Q: What is the minimum Block mass (kg) that is required to open the gate A-B? The density of water is…

A: Density of water, ρw=1000 kg/m3 Density of block, ρb=8000 kg/m3 Specific gravity of oil, sgo=0.9

Q: The car is used to scoop up water that is lying in a trough at the tracks. Determine the force…

A: Find the force needed to pull the car forward.

Q: A single engine plane is cruising at an altitude where the atmospheric pressure is 100 kPa. If the…

A: As per rule i answer only one question ,so i hope you understand.

Q: A-Ethyl alcohol flows in the pipe as shown in Figure below of specific weight 49 lb/ft3. What is the…

A: The mercury head difference in the manometer in terms of Ethyl alcohol can be determined as,

Q: Q2)Water flows up through the vertical pipe that is connected to the transition, Fig bellow. If the…

A: Given Data Rate of discharge flow Q= 0.02 m3/s Apply Bernoulli principle between points A and B

Q: A tank contains a liquid of relative density 0.80. The height of the tank is 4, and the width of the…

A: given data; ⇒relative density (RD)=0.80⇒height of the tank (h)=4m⇒width of tank (w)=2m⇒acceleration…

Q: 4. A single engine plane is cruising at an altitude where the atmospheric pressure is 100 kPa. If…

Q: The water tank is being filled through section 1 at Q1 is 0.01 m3/s and d1 = 100 mm, and through…

Q: Q2) When the force P is applied to the plate, the velocity profile for a Newtonian fluid that is…

Q: 5. The compressed air has a volume of 0.84 ft The temperature is 70 °F and the atmospheric pressure…

A: Given data Volume (v) = 0.84 ft3 temperature(T) = 70 degree fahrenheit Atmospheric pressure = 14.7…

Q: The steel cylinder has a specific weight of 490 (0/f" and acts as a plug for the 1 ft long slot in…

Q: The cylindrical tank containing water accelerates upward with az= 3.5 m/s2 while it rotates about…

A: Given: The upward acceleration of the water, a = 3.5 m/s^2 The radius of the tank, R = 0.3 m The…

Q: Assuming non-viscous flow, determine the traction force on the flange's bolts shown. We have y=1.8…

Q: A fan in the duct shown below sucks air from the ambient and expels it as a jet at 1 m/s to the…

A: Given:Velocity at A, Va=1 m/sDensity of air, ρ=1 kg/m3

Q: Determine the value of h in the siphon shown if velocity at C was 11.7 m/s. Diameter of the pipe is…

Q: The compressed air has a volume of 0.84 ft The temperature is 70 °F and the atmospheric pressure is…

Q: The velocity distribution within the fluid flowing over plate is given by (u-3/4 Y-Y 2) as shown in…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

A pipe set up is given as seen in the figure. The fluid is oil with a specific gravity of 850
kg/m³. The pressure at the exit is atmospheric pressure. The diameter at the
entrance is 6.4 cm and the diameter at the exit is 2.2 cm. The volume rate of flow is
given as 0.0315 m³/s and thegage pressure at the entrance is 250 kPa. Ignore weight
of the fluid and the pipe. Determine the x-component of the force applied at the
bolts at section 1. Assume that the atmospheric pressure is 1013 mb.
40°
2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Oil (SG = 0.85) is flowing in a 10cm diameter pipe. The elevation of the pipe is 5m above the datum line and the pressure in the pipe is -24KPa. If the discharge in the pipe is 30 L/s, determine the power (in watts) in the stream at that point.
A pump takes water at 60 F from a largereservoir and delivers it to the bottom of anopen elevated tank 25 ft above the reservoirsurface through a 3-in ID pipe. The inlet tothe pump is located 10 ft below the watersurface, and the water level in the tank isconstant at 160 ft above the reservoir surface.The pump delivers 150 gal/min. If the total loss of energy due to friction in the pipingsystem is 35 ft-lb, per 1bm of fluid, calculatethe horsepower required to do the pumping.The pump-motor set has an efficiency of 55%.
The flow rate of the water flowing through the venturi, which has a wide section of 4.91x10^-4 m, is 14.4 L/min, and the values read from the manometer are 0.7 bar and -0.1 bar. Find the area of the narrow section
The oil flows through the vertical venturi tube as shown in the figure. The venturi inlet has a diameter of 20 cm, the isthmus of the venturi is 10 cm in diameter, the pressure at inlet P1 is 41.4 kPa(gage), and the pressure at the isthmus P2 is the same size as the body of water. The same oil which is 1.52 m. Find the flow rate of this oil. The density of the oil is 849 kg/m3.
How do you calculate the pressure in a horizontal pipe given the pipe's radius, the liquid's flow rate, and flow velocity?
6. Water is flowing through a pipe having diameter 300mm and 200 mm at the bottom and upper end respectively. The pressure at the lower(bigger) end is 25 N/cm2 and the pressure at the upper end is 10 N/cm2. Determine the difference in datum head if the rate of flow through pipe is 40 lit/s.
Two opened tanks filled with water are connected by seriel pipe AB and BC. AB pipe has a diameter of 10cm, and BC pipe is 6cm. The length of pipe for AB is 200m and for pipe BC is 150m. The flow rate of water entering the pipe is 0.007m³/s and coefficient of contraction is 0.62. If the energy losses ONLY occur due to the shock loss at sudden contraction and friction, calculate the level difference of the two tanks. Given f = 0.04 for both pipes.
Let the pressure gradient in the pipe be 1500 Pa/m and the diameter of the pipe be 4.0 mm. What is the average speed through this pipe of 20∘C motor oil? What is the average speed through this pipe of 100∘C motor oil?
A pipe line of length 2000 m is used for power transmission. If 110 kW power is to be transmitted through the pipe in which water having a pressure of 490.5 N/cm2at inlet is flowing. If the pressure drop over the length of pipe is 98.1 N/cm2and ff = 0.0065.Determine:The diameter of the pipe and the volume flow rate; and If a nozzle is introduced at the end of the pipe, what would be its diameter and the power transmitted.
1. Water flows through a venturi meter. At the constricted section where the area is 24cm², the pressure is 10.2N/cm², and at the section where the area is 64cm², the pressure is 18.0N/cm². Determine the velocities of water in the larger and smaller pipes and the rate of flow. 2. Why is a water tower generally placed on top of a hill? If the hill is 50m high, can it supply water to the top of a 100-m tal officebbuilding? If not, how does water get to that floor?.
Pump Horsepower in Brine System. A pump pumps 0.200 ft3/s of brine solution having a density of 1.15 g/cm3 from an open feed tank having a large cross-sectional area. The suction line has an inside diameter of 3.548 in. and the discharge line from the pump a diameter of 2.067 in. The discharge flow goes to an open overhead tank, and the open end of this line is 75 ft above the liquid level in the feed tank. If the friction losses in the piping system are 18.0 ft lbf/lb m, what pressure must the pump develop and what is the horsepower of the pump if the efficiency is 70%? The flow is turbulent.
At the Niagara Falls generating station, the water drops 102 m from the intake pipes atthe top of the falls to the turbines below. Calculate the power generated by each tonneof water (1 tonne = 1000 kg) that flows through the station every second. Assume anefficiency of 75 %.