The liquid food is flowed through an uninsulated pipe at 90 ° C. The product flow rate is 0.3 kg / s and has a density of 1000 kg / m³, specific heat 4 kJ / (kg K), a viscosity of 8 x 10-6 Pa s, and a thermal conductivity of 0.55 W / (m) K). Assume that the change in viscosity is negligible. The internal diameter of the pipe is 30 mm with a thickness of 3 mm made of stainless steel (k = 15 W / [m ° C]). The outside temperature is 15 ° C. If the outer convective heat transfer coefficient is 18 W / (m² K), calculate the heat loss at steady state per meter pipe length. a. Find the convection coefficient in pipe = W / m² ° C. b. Calculate heat loss per meter pipe length =

The liquid food is flowed through an uninsulated pipe at 90 ° C. The product flow rate is 0.3 kg / s and has a density of 1000 kg / m³, specific heat 4 kJ / (kg K), a viscosity of 8 x 10-6 Pa s, and a thermal conductivity of 0.55 W / (m) K). Assume that the change in viscosity is negligible. The internal diameter of the pipe is 30 mm with a thickness of 3 mm made of stainless steel (k = 15 W / [m ° C]). The outside temperature is 15 ° C. If the outer convective heat transfer coefficient is 18 W / (m² K), calculate the heat loss at steady state per meter pipe length. a. Find the convection coefficient in pipe = W / m² ° C. b. Calculate heat loss per meter pipe length =

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.12P

See similar textbooks

Similar questions

The liquid food is flowed through an uninsulated pipe at 90 ° C. The product flow rate is 0.25 kg / s and has a density of 1000 kg / m³, a specific heat of 4 kJ / (kg K), a viscosity of 8 x 10-6 Pa s, and a thermal conductivity of 0.55 W / (m) K). Assume that the change in viscosity is negligible. The internal diameter of the pipe is 20 mm with a thickness of 3 mm made of stainless steel (k = 15 W / [m ° C]). The outside temperature is 15 ° C. If the outer convective heat transfer coefficient is 18 W / (m² K), calculate the heat loss at steady state per meter pipe length. a. Find the convection coefficient in the pipe = Answer W / m² ° C. b. Calculate heat loss per meter pipe length = Answer watt.
The liquid food is flowed through an uninsulated pipe at 90 ° C. The product flow rate is 0.4 kg / s and has a density of 1000 kg / m³, specific heat 4 kJ / (kg K), a viscosity of 8 x 10-6 Pa s, and a thermal conductivity of 0.55 W / (m) K). Assume that the change in viscosity is negligible. The internal diameter of the pipe is 20 mm with a thickness of 3 mm made of stainless steel (k = 15 W / [m ° C]). The outside temperature is 15 ° C. If the outer convective heat transfer coefficient is 18 W / (m² K), calculate the heat loss at steady state per meter of pipe length. a.Find the convection coefficient in the pipe = AnswerW / m² ° C. b. Calculate heat loss per meter pipe length = Answerwatt.
Distilled water flowing with a flow rate of 50.2 L / min in the venturimeter with a narrow section of 8.6x10^-5m^2 and a wide section of 6.88x10^-4 m^2 transitions from wide to narrow section. The pressure in the wide cross-section of water at 200C is 0.8 bar and tell whether cavitation will occur. (Contraction Loss = KdV22 / 2g and Kd = 0.35) (Vapor pressure values are given in the table below.)
Water (cp = 4197 J / kgC, k = 0.67W / mC, Pr = 2.2, dynamic viscosity = 352 * 10 ^ -6 Ns / m ^ 2) with a flow rate of 0.01 kg / s and an inner diameter of 0.1 m at 20C temperature It is requested to be heated to 80C. If the pipe inner wall is kept constant at 120C, what is the average logarithmic temperature difference with fully developed flow acceptance? a. 65.48 C b. 43.3 C. c. 316.3 K D. 723.4 K e. 2300 K.
You are being tasked as a wind tunnel engineer to investigate the performance of newly designed high-speed wind tunnel in UPNM. An exhaust gas flows through a nozzle where the inlet area is 5,000 cm2.At this inlet, the gas has a velocity of 1,200 m/s, temperature of 1,500oC,and pressure of 6,000 kPa. Initial measurement revealed that the pressure at the exit of the wind tunnel is 100 kPa. Based on this information, analyze and investigate ; i. Mach number at inlet of the nozzle ii. The velocity of gas at exit iii. The area of the nozzle at exit Take specific heat ratio for the exhaust gas, ? to be 1.7 and the gas constant, R to be 205 J/kg.
A capillary tube has an 8mm inside diameter through which liquid fluorine refrigerant R-11 flows at a rate of 0.03 cm3/s. The tube isto be used as a throttling device in an air conditioning unit. A model of this flow is constructed by using a pipe of 3cm inside diameter and water as the fluid medium. (Density of R-11 = 1.494 g/cm3 and its viscosity is 4.2 x10-4 Pa.s; Density of water is 1g/cm3 and its viscosity 8.9 x10-4 Pa.s)a) What is the required velocity in the model for dynamic similarity? Hint: For flow through a tube the Ne number can be expressed in terms of the Reynolds numberb) When dynamic similarity is achieved the pressure drop is measured at 50 Pa. What is the corresponding pressure drop in the capillary tube?Hint: In this case the Euler number defines dynamic similarity with reference to the static pressure drop
An ideal gas at 250 °C and atmospheric pressure flows through a smooth pipe with ID 6-in. The molecular weight of the ideal gas is 35 g/mol, and its viscosity is 0.002 cP. If the average velocity of the gas is 3.5 m/s, determine the pressure drop per unit length (m).
Water at 20 C flows in a smooth pipe 0.04 m indiameter at a Reynolds number of 50,000. Thewall temperature is maintained at 25C. The bulk temperature and film temperature are assumed to be at 20C. Using Colburn analogy find the value of heat transfer coefficient. The properties of water are: Density = 999 kg/m3; viscosity = 1 cp; Pr = 6.94; Specific heat 4182 K/kgK; k=0.603 W/mK
A solid ball is dropped into a water container for cooling. The ball has a diameter of D = 4 mm and sinks at a constant terminal velocity of Ut = 0.01 m/s. The thermophysical properties of the solid ball are: density ρ = 8000 kg/m3, thermal conductivity k = 200 W/m · K, and specific heat c = 1000 J/kg · K. The thermophysical properties of the water are: density ρw = 1000 kg/m3, kinematic viscosity νw = 10^(−6) m^(2)/s, thermal conductivity kw = 0.6 W/m · K, and Prandtl number Pr = 7. The vertical distance for the ball to sink from the initial fully submerged depth to the bottom of the container is H = 0.1 m. The initial temperature of the ball is T0 = 800 K, and the water temperature is T∞ = 300 K.Given correlations: For the convection heat transfer caused by flow past a sphere, the averaged Nusselt number is NuD = 2 + 0.6*(Re^(1/2))*(Pr^(1/3)) Questions:(1) Determine the averaged convection heat transfer coefficient h, and check if the LumpedCapacitance Method can be used to solve…
An ideal gas in which the pressure P is related to the volume V by the equation PV=60 m2/s2 flows in a steady isothermal flow along a horizontal pipe of inside diameter di =0,04m. The pressure drops from 0.5 atm to 0.35 atm in a 1000 cm length. Calculate the mass flowrate in kg/(sm2) if we can assume that the friction factor jf stay constant at a value of 5,2´10-3.
Engine oil at 40 C [density 876 kg/m^3, viscosity 0.2177 kg/m.s] flows in a 20-cm-diameter pipe at a velocity of 0.9 m/s. The pressure drop (in Pa) of oil for a pipe length of 28 m is ?
Air at 1.7 atm gauge and 15°C enters a horizontal 75-mm steel pipe that is 70 m long. The velocity at the entrance of the pipe is 60 m/s. Assuming isothermal flow, what is the pressure at the discharge end of the line? ANSWER SHOULD BE 1.982 atm