The load in the figure below is attached to the wall with a ball joint at point A. Calculate the displacement of the point C, ignoring the weight of the rigid bar in the system standing in balance on the plane (in two dimensions), with all the other values specified in the question in accordance with the manufacturing norms, with the data you will determine yourself (no value can be zero). Note W = 641 Steel wire E= 45 GPa Bronze wire E= 48 GPa  Rigid bar E= 50 GPa

Q: Links (1) and (2) support rigid bar ABCD shown in the figure. Link (1) is bronze [E = 15,200 ksi]…

A:

Q: Figure Q2 shows a rigid link supported by a pin at C and two A-36 steel wires. Each wire having an…

A:

Q: Consider the frame shown in Fig 4. A 100N load is suspended around a fixed drum with radius 2 m…

A:

Q: The deflection of the composite spring when subjected to the greatest load A fixed bar is pinned at…

A: Given DataD=150mmd=10mmboth spring have same materialW=10kg Here in this problem we have to…

Q: The figure Q3 below shows a bolt holding together two components. The bolt has a load bearing…

A: Thickness of component 1, t1 = 5 mm Thickness of component 2, t2 = 10 mm Modulus of elasticity of…

Q: The cantilever bar in the figure is made from a ductile material and is statically loaded with Fy=…

A: The forces acting on the cantilever beam are: Fy = 300 lb Fx =0 Fz =0   To find: The critical…

Q: Consider the frame shown in Fig 4. A 100N load is suspended around a fixed drum with radius 2 m…

A:

Q: AB, BC, BD ropes made of material with elasticity value in Table 2 are in balance as shown in the…

A: Given Data: θ=90° β=120° α=150° FAB=40000 N Areas: AAB=200 mm2 ABC=173 mm2 ABD=100 mm2 Lengths:…

Q: Q3) A short stepped bar is shown in Figure below. The stiffness of the large section is 12 kN/mm and…

A: Given data: k1=12 kN/mmk2=8 kN/mmF=6 kN Need to determine the displacement of the nodes 2 and 3.

Q: Cable Beam In the figure above, a beam of weight 750 N and length 3.5 m is suspended horizontally.…

A:

Q: A 7.5kg sign is hung off of the end of a 3.7kg metal arm as shown in the figure. (Note that while…

A: Given Data: The mass of the arm is m1=3.7 kg. The mass of the sign is m2 = 7.5 kg. The center of…

Q: The diameter of the pin to be used at the B point in the brake mechanism in the figure is dB = 12 mm…

A:

Q: how many times is the system

A: For solution refer below images.

Q: Problem 4: Constrained Modulus A mounting block made of butyl rubber of modulus = 0.0015 GPa is…

A:

Q: The structure shown in Figure 3.1 consists of bar BD and two rods, AD and CD. Assuming that the…

A: Draw the given diagram showing the axes and specifying B as the origin. From the figure, taking B…

Q: . Illustrated in the figure is a 1.5 in diameter steel countershaft that supports two pulleys.…

A:

Q: Rigid bar ABCD shown in the figure is supported by a smooth pin at D and by vertical aluminum alloy…

A:

Q: A stepped 100 N-m as shown in figure below. Modulus of rigidity of material is 90 GPa, then angle of…

A: Given data: Torque, T=100 N-m G=90 GPa

Q: A vertical steel bar shown in figure Q1 is subiected to a compressive load of 75 kN. If the stress…

A:

Q: 2. The figure shows a spring toy. The toy weight is 100 N. The spring free-length is 500 mm, mean…

A: Given that, Weight of the toy, W=100 N,Length of the spring, L=500 mm,Mean diameter of the spring,…

Q: The metallic hollow pipe shown in Figure Q1 is fixed at both its ends, and is under axial…

A:

Q: Compute the vertical displacement of joints B and C for the frame shown in Figure P8.30. Given: I =…

A: Draw the reaction diagram of the system of the structure. The load is acting at the joint of the…

Q: A portion of the stress-strain curve for a stainless steel alloy is shown in Figure Q-2. A 350 mm…

A:

Q: 2. The figure shows a spring chair. The chair weight is 100 N. The spring free-length is 500 mm,…

A:

Q: Problem 8 Problem 8.2-6 A spherical steel pressure vessel (diameter 480 mm, thickness 8.0 mm) is…

A: Given data as per question Diameter =480 mm Thickness = 8.0mm E=205 Gpa V =0.30

Q: 3. A hollow cylindrical cast iron column 200 mm external diameter and 25 mm thick is 6 metres in…

A: Given, External diameter, Do=200mmThickness, t=25mmInternal diameter, Di=150mmLength of the column,…

Q: A cable and D-pulley system is used to bring a 230 kg (ACB) pole to the vertical position, as shown…

A:

Q: Q-1 A solid circular rod with a diameter d= 18 mm is shown in Figure Q-3. The rod is made of an…

A:

Q: For the bar assemblages shown in Figure P3-3, determine the nodal displacements, the forces in each…

A: (a) The stiffness matrix is given by  …….(1) For element 1 substitute the values of A, E and L in…

Q: A bar, AB, with length L = 2 m and with weight Wand is held by two springs (see figure 1.1). The…

A: Calculated the distance x ,where force p is applied ,bar become in horizontal ,when the  unstressed…

Q: A portion of the stress-strain curve for a stainless steel alloy is shown in Figure Q-2. A 350 mm…

A: Write the expression of the normal strain.

Q: (a) A steel cable with nominal diameter 25 mm as shown in Table Q2(a) is used in a construction yard…

A:

Q: A pin in a knuckle joint carrying a tensile load Fdeflects somewhat on account of this loading,…

A:

Q: In the figure, one end of a uniform beam of weight 130 N is hinged to a wall; the other end is…

A: To find: The tension in the wire. Given: The weight of the one end of the beam is hinged to the wall…

Q: The cantilever bar in the figure is made from a ductile material and is statically loaded with Fy=…

A:

Q: P1.6 Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in Figure…

A:

Q: Consider the steel shaft in the figure as shown. The working stresses are ơw 120 MPa and Tw = 70…

A: given; ⇒shear stress(τ)=70MPa⇒minimum diameter(d)=?⇒radius(R)=0.5m

Q: 8. Calculate the horizontal reaction at O in Fig Q8 due to the load P = 177 N applied to the bar OB.…

A:

Q: Compute the total elongation of the bar shown in Figure P3-37 if it is made from titanium 3-37.…

A: Reaction at A; Axial loading diagram: Now,

Q: At the figure below you see a group of 2 springs – C1 and C2. Determine the type of connection…

A: Given data F = 500 N  C1 = 100 N/mm C2 = 230 N/mm  To determine  Type of connection  and overall…

Q: For the bar assemblages shown in Figure P3-4, determine the nodal displacements, the forces in each…

A:

Q: The cantilever bar in the figure is made from a ductile material and is statically loaded with Fy=…

A:

Q: 1.5-6) A specimen of a methacrylate plastic is tested in tension at room temperature (see figure),…

A: Using the stress-strain data given in the problemstatement, plot the stress-strain curve:

Q: The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

A: The free-body diagram of the bar will be given as follows,

Q: The pulley shown in Figure P1.27 is connected to a bracket with a circular pin of diameter d = 6 mm.…

A: Given Data: The diameter of the circular pin is, d=6 mm. The width of the bracket is, b=25 mm. The…

Q: Q3) A short stepped bar is shown in Figure below. The stiffness of the large section is 12 kN/mm and…

A:

Fire safety

Fire safety is a new domain emerged in the early 90s to enable the design of buildings, structures, and infrastructure against destruction through fire. It also includes the provisions of building codes. This field is mostly associated with the design and efficient planning of a building, to reduce the destruction caused by fire. The branch of engineering that deals with it for the safety of the buildings from destruction of fire, is known as fire safety engineering.