P1.6 Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in Figure P1.6/7. One load of P = 1,500 lb is applied to the assembly at A, two loads of Q = 900 lb are applied at B, and two loads of R = 1,300 lb are applied at C. The diameters of rods (1), (2), and (3) are, respectively, d, = 0.625 in., d, = 0.500 in., and d, = 0.875 in. Determine the axial normal stress in each of the three rods.

P1.6 Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in Figure P1.6/7. One load of P = 1,500 lb is applied to the assembly at A, two loads of Q = 900 lb are applied at B, and two loads of R = 1,300 lb are applied at C. The diameters of rods (1), (2), and (3) are, respectively, d, = 0.625 in., d, = 0.500 in., and d, = 0.875 in. Determine the axial normal stress in each of the three rods.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure Q3 shows a steel bar of diameter 16 mm and length 600 mm subjected to axial forces.If E = 210×103 N/mm2for steel, determine the change in its length.
A steel bar of 5 mm is heated from 15° C to 40° C and it is free to expand. The bar Will induce A. no stress B. shear stress C. tensile stress D. compressive stress
7.10 A rigid bar is suspended by three equally spaced wires of equal length. Theouter wires are steel and are 2 mm in diameter, the centre wire is copper andis 5 mm in diameter. If the weight of the rigid bar is 2,25 kN, calculate the loadcarried by each wire. If the temperature of the system is now raised by 90 °C, what will the magnitude and nature of the resultant stresses set up in the steeland copper wires be. (Let EST = 200 GPa; Ecu = 100 GPa; aST = 12 x 10_6/°C;acu = 18 x 10-6/°C?)
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loding if three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in z direction. If v=0.30 and E=29x10^6 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading. DetermineNormal strain in x, y & z direction.Elongation in x, y & z direction.
6. A compression force, F=4+3.5cos (45t) in kN is applied to the rod of an ideal cylinder with a bore diameter of 9.4 cm. Assuming the rod-side of the cylinder is at atmospheric pressure, what gauge pressure, P, must be applied to the cap-side of the cylinder to keep the load stationary?
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
Figure Q2 shows an arrangement used to transfer materials F to a construction site. The rod OB is fixed at datum O. One of the systems used have dimension and loads as given in Table Q2. During operation, Pulley A is rotated as shown to move the load upwards. The inclination angle of rod OB is θ = 45O. Determine: Stress in Rope 1 (in MPa) Stress in Rope 2 (in MPa) Extension in Rope 2 (in mm) The minimum diameter of Rope 2 (in mm) if the stress is at yield
Figure Q2 shows the cross-section of a closed ended thick-walled cylinder with inner radius, ri, 0.1 mand outer radius, ro, 0.2 m. The cylinder is subjected to internal pressure, pi and external pressure, po.One of the design specifications is to maintain the hoop stress at the outer surface of the cylinder at zerovalue. If po = 50 MPa and by using Lame’s equations for thick-walled cylinder, (a) determine the value of pi to achieve the design specification (b) sketch the hoop, radial, and longitudinal stress variations across the wall thickness and label their values at the inner and outer radius of the cylinder (c) determine the absolute maximum shear stress existing in the cylinder wall material
A bar of dimension 120 mm x 50 mm x 40 mm, is subjected to an axial pull of 50 kN. The measured extension is 0.25 mm and change in depth is 0.0036 mm. Calculate: (i) Young’s Modulus, (ii) Poisson’s ratio (iii) Shear Modulus. and (iv) Bulk Modulus (i) The Young's modulus is (N/mm2) = _________________ (ii) Poisson's ratio = ___________________ (iii) The shear modulus is (unit in N/mm2) = ________________ (iv) The Bulk modulus is (unit in N/mm2) =
Solve the problem below. For your final answer, use whole number. An extra flexible 8 × 19 steel wire rope of 38 mm diameter is used with a 2 m diameter hoist drum to lift 70 kN of load. The wire rope has a length of 900 meters. The maximum speed is 3 m / s and the acceleration is 1.5 m / s2. The diameter of the wire may be taken as 0.05 d, where d is the diameter of wire rope. The modulus of elasticity of the entire rope is 84 × 103 N/mm2. The weight of the rope is 53 N/m length. Determine the effective load during acceleration of load in kN.
A steel bar, the material of which is S355 J2 G3, binds two walls together. Pre-tensioning in tie bar 4.3 kN. The temperature of the rod increases by 15 °C. Calculate the normal stress in the cross section of the bar. L = 600 mm, α = 12μ 1/°C, E = 200 GPa and d = 25 mm . Give the answer in MPa as a whole number as a numerical value only. Correct answer to exercise should be = -27
A uniform ladder 10m long and weighing 350N rests against a smooth wall at an angle of 30° with the wall. A 700N man stand 6m up from the bottom of the ladder. Find the horizontal force necessary to keep the ladder from slipping.