The load on a bolt consists of an axial thrust of 10 kN, with transverse shear force of 6 kN.Calculate the diameter of the bolt according to (a) maximum principal stress theory,(b) maximum shear stress theory, and (c) strain energy theory. Take factor of safety to be 3,Which is a safe theory? yield strength= 285 , v=0.3

The load on a bolt consists of an axial thrust of 10 kN, with transverse shear force of 6 kN.Calculate the diameter of the bolt according to (a) maximum principal stress theory,(b) maximum shear stress theory, and (c) strain energy theory. Take factor of safety to be 3,Which is a safe theory? yield strength= 285 , v=0.3

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.10P: What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm,...

See similar textbooks

Similar questions

What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
in the design of shafts made of ductile materials subjected to twisting moment and bending moment, the recommended theory of failure is (a) maximum principal stress theory (b) maximum principal strain theory (c) maximum shear stress theory (4) maximum strain-energy theory
A Steel shaft is subjected to an end thrust producing a stress of 90 MPa and the minimum shearing stress on the surface arising from torsion is 60 MPa .The yield point stress of the material in simple tension was found to be 300 MPa. calculate the factor of safety of the shaft according to the following theory 1)maximum shear stress theory
Two solid shafts, 50 mm in diameter, are connected by a flange coupling with six bolts and a pitch circle diameter of 95 mm. If the maximum shear stress in the shaft due to a torque is to be the same as the shear stress in the bolts, calculate a suitable bolt diameter. If the maximum working shear stress is limited to 55 MPa, what maximum power will be transmitted by the coupling at 700 r/min?
Hexagonal nuts for 6.25mm diameter bolts have a height of 5.5mm. If the ultimate strength of the nut material in shear is 103MPa, what is the most nearly the maximum allowable shear force on the nut thread using a safety factor of 5?
.A flanged bolt coupling consists of six 12.5 – mm steel bolts evenly spaced around a bolt circle 300mm in diameter, and four 19 – mm aluminum bolts on a concentric bolt circle 200 mm in diameter.What torque can be applied without exceeding 62 MPa in the steel or 42 MPa in the aluminum?Assume Gst = 82.7 GPa and Gal = 27.6 GPa.
An input shaft of a gearbox with motor power P = 7 kW and rotation number n = 1300 rpm. The diameter of an input shaft is d = 20 mm and its material is 16MnCr5. A force of F = 2800 N forces the shaft due to the operation of a gear wheel connected with a wedge on the input shaft. The distances of the gear from the bearings are given as L₁ = 40 mm and L2 = 60 mm. In the most dangerous section, you are required to check the strength according to the S = 3 safety factor. If the section is unsafe in terms of strength, what changes would you make in the design to make it safe? (The surface of the spindle is machined as fine chips, reliability poor Kg = 1.).
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
A shaft with a diameter of 50 mm and a length of 1300 mm with a safe shear yield strength of 20 N / mm2 is subjected to 565 Nm of torque. What is the torsion angle and applicability? (G = 80GPa)
A flanged coupling rotating at 400 rpm have 4 steel bolts evenly tightened around a 100 mm bolt circle. What diameter of bolt should be used if the power transmitted is 26.5 kW and the design shearing stress of the bolt is 12 MPa?
Two pipes were connected by a flanged bolt coupling. The material properties are as follows: For outer bolts, 12 pieces, 16 mm diameter, on a mean radius of 150 mm, G = 28 GPa. For the inner bolts, 8 pieces, 12 mm diameter, on a mean radius of 100 mm, G = 20 GPa. Determine the total torque of the system if the shearing stress is limited to 30 MPa in the bolts. (Draw also the FBD) with complete solution
A part is loaded with a combination of bending, axial, and torsion such that the following stresses are created at a particular location:Bending: Completely reversed, with a maximum stress of 60 MPaAxial: Constant stress of 20 MPaTorsion: Repeated load, varying from 0 MPa to 70 MPaAssume the varying stresses are in phase with each other. The part contains a notch such that Kf,bending = 1.4, Kf,axial = 1.1, and Kf,torsion = 2.0. The material properties are Sy = 300 MPa and Su = 400 MPa. The completely adjusted endurance limit is found to be Se = 160 MPa. Find the factor of safety for fatigue based on infinite life, using the Goodman criteria. If the life is not infinite, estimate the number of cycles, using the Walker criterion to find the equivalent completely reversed stress. Be sure to check for yielding.