The losses in the blade of a steam turbine due to friction is 20%. If the relative velocity of steam at blade inlet is 300 m/s, the relative velocity of steam at blade outlet is a. 240 m/s O b. 200 m/s O c. 60 m/s 80 m/s

The losses in the blade of a steam turbine due to friction is 20%. If the relative velocity of steam at blade inlet is 300 m/s, the relative velocity of steam at blade outlet is a. 240 m/s O b. 200 m/s O c. 60 m/s 80 m/s

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Similar questions

A boiler requires 100 000 m3/hr of standard air. The mechanical efficiency of fan to be installed is 70%. Determine the size of driving motor needed assuming fan can deliver a pressure head of 160mm of water and outlet velocity of 20m/s. A. 60kw B. 81.8kw C. 75.8kw D. 71.81kw
A pump with an impeller diameter of 0.02 m, an impeller speed of 58.3 rpm, a * total capacity of 12 L/s, an available head of 70 m, and a brake power of 12 kW is used to pump water. Determine the capacity of a homologous pump with twice the impeller diameter and operating at half the speed. Choices: A.60L/S B.36 L/S C.48 L/S D.72L/S
Three pumps are connected in series. According to pump performance curves, the free delivery of each pump is as follows: Pump 1: 1600 L/min Pump 2: 2200 L/min Pump 3: 2800 L/min If the flow rate for this pump system is 2500 L/min, which pump(s) should be shut off? (a) Pump 1 (b) Pump 2 (c) Pump 3 (d) Pumps 1 and 2 (e) Pumps 2 and 3
A pump rated at 65% efficiency is used to transport water from a large open reservoir to a point 10m above at a rate of 450 L/min, into a vented tank. Assuming friction is negligible and that the efficiency of the motor is 77%, how much electricity is required to keep the process running for 24 hours? Choices: A. 29.37 kWh B. 35.28 kWh C. 56.71 kWh D. 43.21 kWh
Three pumps are connected in parallel. According to pump performance curves, the shutoff head of each pump is as follows: Pump 1: 7 m Pump 2: 10 m Pump 3: 15 m If the net head for this pump system is 9 m, which pump(s) should be shut off? (a) Pump 1 (b) Pump 2 (c) Pump 3 (d) Pumps 1 and 2 (e) Pumps 2 and 3
The net head delivered by a pump at a rotational speed of 1000 rpm is 10 m. If the rotational speed is doubled, the net head delivered will be (a) 5 m (b) 10 m (c) 20 m (d ) 40 m (e) 80 m
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. i. Determine Delta Z (Z2 - Z1) in ft. ii. What is the actual shaft work needed for this particular mass flow rate in (ft-lbf)/s. iii. What is the mass flow rate of the water in lbm/s?
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. answer the ff: i. Determine the velocity of the water at point 2. ii. Reynolds number for the flow. iii. A pump efficiency of 55% means that the theoretical work needed for the process is 55% of the actual work needed. In other words, 55% more shaft work is necessary. Determine the theoretical shaft work required in foot-pound force per pound mass.
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. i.Let us set our first point at the surface of the large reservoir, and the second point at the surface of the open elevated tank. Determine the velocity of the water at point 1 in ft/s. ii.What is the density of water at the conditions stated in lb/ft3? iii.If 1 horsepower is equivalent to 500 (ft-lbf)/s, the pump should be able to supply how much hp?
A pump takes water at 60°F from a large reservoir and delivers it to the bottom of an open elevated tank 25 ft above the reservoir surface through a 3 inch ID pipe. The inlet to the pump is located 10 ft below the water surface, and the water level in the tank is constant at 160 ft above the reservoir surface. The pump delivers 150 gal/min. If the total loss of energy due to friction in the piping system is 35 ft·lbf/lb. The pump and its motor have an overall efficiency of 55 %. a. Assuming that the large open reservoir is open to the atmosphere as well, what is the mechanical energy balance eq for the system? b. What is the Reynolds number for the flow ?
A centrifugal pump operating under steady flow conditions delivers 2,813 kg/min of water from an initial pressure of 86,976 Pa to a final pressure of 296,902 Pa. The diameter of the inlet pipe to the pump is 19.82 cm and the diameter of the discharge pipe is 11.28 cm. What is the work in J/s?
The Head -flowrate curve for a centrifugal pump is given by: HP = 28 -30Q2 Where, HP is in meter and Q is in m3/s . This pump is used to pump water for a system with the following (H-Q) curve: HS = 8 + 150Q2 Where, HS is in meter and Q is in m3/s . What is the resulting flow rate in the system if three pumps are used in series? (a) 0.56 m^3/s (b) 0.48 m^3/s (c) 0.33 m^3/s (d) 0.36 m^3/s HINT: what is the resulting Flow-rate in the system if three pumps are used in series ? Choose correct option above