i need the answer quickly A chain pulls tangentially on a 40.6-kg uniform cylindrical gear with a tension of 72.5 N. The chain is attached along the outside radius of the gear at 0.650 m fromthe axis of rotation. Starting from rest, the gear takes 1.70 s to reach its rotational speed of 1.35 rev/s. What is the total frictional torque opposing the rotation ofthe gear?Need detail and step by step answer (only typed answer not handwritten please)Short answer and incorrect answer gives u downvote

Given data: m=40.6 kgT=72.5 Nt=1.7sN=1.35 rev/sr=0.65 m Need to determine the total frictional…

Answered: A chain pulls tangentially on a 40.6-kg…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The mass of the belt is 0.6kg/m and the tension on the tight side of the belt is 1.7kN.the coefficient of friction between the belt and the pulley is 0.2 and the angular speed N, of the belt is 400rpm.Angle of lap fita and the diameter D of the pulley are 150° and 50cm respectively.with the addition of centrifugal tension, Design the belt drive by determine (A) velocity of the belt (B) centrifugal tension (C) tension on the slack side of the belt (D) power transmitted at this speed in kilowatts (E) maximum
If the man pulls the strap with constant acceleration during a short time interval Δt, calculate the force (in Newtons) that he must exert in spinning up the disc. These are the numbers. Strap's final speed = v = 1.5 m/s. The disc's radius is R = 0.4 m The small disc's radius is 2 cm The disc's mass is M = 2.4 kg The short time interval is Δt = 0.3 s The disc initially is non-rotating.
Hello, can you help me answer this question with complete solution and illustration. *A Land Cruiser having a mass of 1500 kg goes through an intersection and i stravelling from north to south when it is hit by a Mitsubishi Pajero of mass 220 kg travelling from east to west. The two cars slid as one due to impact and stops 5.39 m west and 6.43 m south measured from impact point. It is known that the coefficient of kinetic friction between the cars and the road is 0.75. How fast each of the car is travelling before collision?
A 50.0 kg grindstone is a solid disk 0.530 m in diameter. You press an ax down on the rim with a normal force of F = 160 N. The coefficient of kinetic friction between the blade and the stone is 0.60, and there is a constant friction torque of 6.50 N⋅m between the axle of the stone and its bearings. a) How much force must be applied tangentially at the end of a crank handle 0.500 m long to bring the stone from rest to 120 rev/min in 7.00 s? b) After the grindstone attains an angular speed of 120 rev/min, what tangential force at the end of the handle is needed to maintain a constant angular speed of 120 rev/min? c) How much time does it take the grindstone to come from 120 rev/min to rest if it is acted on by the axle friction alone?
1. If there is no friction between shaft AB and the collar, what angular velocity θ˙˙ must the mechanism have to keep the collar at r=300 mm from the vertical axis? Express your answer to three significant figures. 2. Consider the same mechanism again, with m=2.95 kg, d=225 mm, k=250 N/m, only now, instead of being smooth, the collar and shaft have a maximum coefficient of friction of μs=0.297. What is the minimum angular velocity required to keep the collar at a constant distance r=300 mm from the axis of rotation? Express your answer to three significant figures.
If there is no friction between shaft AB and the collar, what angular velocity Ö must the mechanism have to keep the collar at r= 660 mm from the vertical axis? Consider the same mechanism again, with m = 3.3 kg, d = 275 mm, k = 180 N/m, only now, instead of being smooth, the collar and shaft have a maximumcoefficient of friction of 0.74. What is the minimum angular velocity required to keep the collar at a constant distance r= 660 mm from the axis of rotation?
An object of mass 12 kg is suspended from a pulley which has a mass of 6 kg and a radius of rotation of 0.25 m. If at that time the pulley rotates with an angular velocity of 5 rad/s, we want to know that when the object moves down a distance of 2 m, then at what speed is the pulley rotating? If the friction force on the pulley bearing produces a moment of resistance of 2 N-m
Two blocks with masses M1 and M2 are connected by a massless string that passes over a pulley as shown. M1 is on an incline of 49.5° with coefficient of kinetic friction μ1 = 0.205. M2 has a mass of 4.84 kg and is on an incline of 35.5° with coefficient of kinetic friction μ2 = 0.105. The pulley can be modeled as a disk with a mass of 305 g and radius of 15 cm. When the system is released, Block M2 accelerates down the incline at rate of 0.52 m/s2. (a) Determine mass of block 1 and the tension forces in the string connecting the blocks and the pulley. Draw accurate free body diagrams of both blocks and pulley, label each force correctly and show the steps in derivation of equations. (b) How much energy will be dissipated by friction 2 second after the blocks are released?
A locomotive consists of multi cylinder reciprocating engine running at a speed of 8 r.p.s having a stroke length of 29cm, which carries a mass of reciprocating part whose magnitude is 11kgs with a revolving part of 5kgs rotating at 17cm radius. If two third of the reciprocating parts and all the revolving parts are to be balanced, determine the following when the crank has rotated 500 from top dead centre to bottom dead centre. 1. Maximum primary unbalanced force of reciprocating mass in newtons 2. Balancing mass required at a radius of 41cm in kgs 3. Variation of maximum & minimum tractive force in newtons 4. Variation of maximum & minimum swaying couple for the given centre distance 76cm between the two cylinders in (N-m) 5. Magnitude of Hammer…
A centrifugal clutch has four shoes, each of mass 0·35 kg. When at rest, the radialclearance between the shoes and the clutch drum is 15 mm and the radius to the centre ofgravity of the shoes is 225 mm. The shoes are held on retaining springs of stiffness 10kN/m and the internal diameter of the clutch drum is 600 mm. The coefficient of frictionbetween the drum and the shoes is 0·3.Determine:(a) The speed (in rev/min) at which the clutch starts to engage. For a rotational speed of 1200 rev/min:(b) The force each shoe exerts on the drum. (c) The torque transmitted. (d) The power transmitted.
A hoop of radius 95mm and mass 100g is rotated via a capacitor driven power source with P(t)=1.61e-1.3tW. (since it is a hoop, it is a special case, and r=rG) Assuming the hoop is accelerated from rest, determine the rotational velocity after t=8.5s. [rad.s-1] Determine the rotational speed of the hoop after t=8.5s if the power source acts to roll the particle from rest on a horizontal surface. [rad.s-1]
A plank with a mass M = 6.00 kg rests on top of two identical, solid, cylindrical rollers that have R = 5.00 cm and m = 2.00 kg. The plank is pulled by a constant horizontal force Fs of magnitude 6.00 N applied to the end of the plank and perpendicular to the axes of the cylinders (which are parallel). The cylinders roll without slipping on a flat surface. There is also no slipping between the cylinders and the plank. a. Find the initial acceleration of the plank at the moment the rollers are equidistant from the ends of the plank. b. Find the acceleration of the rollers at this moment. c. What friction forces are acting at this moment?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS