The material distorts into the dashed position shown, where d = 11 mm (Figure 1) Determine the average normal strains ex, éy and the shear strain Yxy at Part B Determine the average normal strain along line BE Figure 1 v of 1 24 D- 50 mm B 200 mm 50 mm 150 mm

The material distorts into the dashed position shown, where d = 11 mm (Figure 1) Determine the average normal strains ex, éy and the shear strain Yxy at Part B Determine the average normal strain along line BE Figure 1 v of 1 24 D- 50 mm B 200 mm 50 mm 150 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.7.25P: On the surface of a structural component in a space vehicle, the strains arc monitored by means of...

See similar textbooks

Related questions

Q: The X- axis strains with oriented angle of the bone surface are shown in table X- axis strain (x…

Q: In uniaxial loading the poisson's ratio is 0.30 and the strain in the x- direction is 250 x 1O^-6 .…

Q: M13.5 Strain measurement with rosettes scenes Ea 500 µE Ep -200 µE %3D Ec 250 µE 30° 30° Ex ( με) Ey…

Q: 2a. The delta strain gauge rosette shown in Figure 2a is attached to a structural component and…

A: Delta Strain Gauge losette Given : θ=0 EA=775×10-6 and E=200×103 MPa…

Q: The 45° strain rosette shown in figure below is mounted on the surface of a thin shell. The…

A: Solution.

Q: A differential element on the bracket as shown in Figure Q1 is subjected to plane strain that has…

Q: ongitudinal strain for a wire is 0.03 and isson's ratio is 0.5, then its lateral strain 0.003 75ח ת…

A: Option (3) is correct. Lateral strain = 0.015

Q: The state of plain strain at a point in a body is given by €x = 800 x 10-6, €y = 200 x 1076, and yy…

Q: The 45° strain rosette is mounted on a surface of the bracket . The bracket is made from steel with…

Q: A material is subjected to two mutually perpendicular strains ex=350x10-6, ey=50x10-6 with unknown…

Q: A differential element on the bracket as shown in Figure Q1 is subjected to plane strain that has…

Q: The state of plane strain on an element has components €z = -340(10 6), Ey = 0, and Yzy = 130(10 ®).…

Q: Consider a shaft of diameter 50mm and length 5m, attached with a strain gauge at an angle of 0 = 49…

A: The equation of the torsional moment is given by, Here, T represents the torque, Ip represents the…

Q: Q3/ The material distorts into the dashed position shown in fig.2. Determine the average normal…

Q: The below-given figure is an example of strain energy. Select one: O True O False

Q: Q.3) A structural member in plane strain has the following strains at a point: Ex = 360 µ, 8-230 μ ,…

A: Given:εx=360 μ εy=230 μγxy=150 μa)strain at…

Q: A set of strain rosette with three strain gauges at 120° apart is attached onto a steel structure…

Q: The state of strain in a plane element is Ex = -300 x 10-6 , Ey= 450 x 10-6, and Yxy = 275 x 10-6.…

Q: Figure Q2 (b) shows a strain rosette that is attached on the surface of a production equipment. The…

A: For solution refer below images.

Q: D 2 mm 5 mm 15 mm A В 15 mm

Q: If e and have the same signs, then the absolute maximum shear strain will be equal to the maximum…

Q: H.W. 3 The X- axis strains with oriented angle of the bone surface are shown in table X- axis strain…

A: The strain is given at different angles which are giving below – The strain at any angle can be…

Q: A rectangular titanium plate has the following dimensions. a = 20 mm, b = 15 mm, and c=5 mm.…

Q: ain that has the following components: ex = 150µ, ey = 200µ, yxy = -700µ. using the strain…

Q: The state of strain on an element has components = -280(10-6), ɛ, = 120(10-6), Yæy = 180(10-6).…

A: Given data, εx=280(10-6) εy=120(10-6) γxy=180(10-6)

Q: 1. At a critical point on the free surface of a loaded beam, the strains are measured in three…

A: Only one question is allowed to solve.

Q: What is the approximate yield stress of the material shown Stress-Strain Curve 800 700 600 500 400…

A: Option b is correct.

Q: If a rubber material is deformed as shown in the following figure, determine the normal strain along…

A: As, ∈x=320=0.15&, ∈y=-220=-0.1

Q: A 60° strain rosette is glued to a girder. Under certain loading conditions at an instant, the…

A: Given data, εa = Strain at strain rosette a = 4.4x78 μ = 343.2μ εb = Strain at strain rosette b =…

Q: If a rubber material is deformed as shown in the following figure, determine the normal strain along…

Q: Q1: The stresses measured at a point on bone are ox =5 MPa ,0y = -7 MPa and txy-2.4 MPa find: 1. The…

A: Given Data σx=5MPa σy=-7MPa Txy=2.4MPa Poison ratio, v=0.3 Principle stress expression

Q: The state of strain at the point on the pin leaf has components of € = 200(10-6) Ey 180(106), and…

Q: Figure 1: P = 400 kN 30° 1000 mm Area 30 mm 20 mm In Figure 1, if the Young modulus is 200 Gpa, the…

Q: A differential element is subjected to plane strain that has the following components; Px =…

A: Given: The components of the plain strain is εx=950×10-6,εy=420×10-6 and γxy=-325×10-6 a> Normal…

Q: Exercise 2 : For the constant strain triangular shown in figure 2. Determine the strain-displacement…

Q: The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Q1. The bracket is…

A: Esteel=120 GPaμ=.28 εa=100+60×10-6 εb=-200×10-6εc=-180×10-6 θa=0° ,θb=45°,θc=90°

Q: The strains on the surface of an experimentaldevice made of pure aluminum (E = 70 GPa,n = 0.33) and…

A: Given Pure aluminum: E = 70 GPa Poisson ratio = 0.33 Find Stress in the x direction

Q: (b) A differential element on the bracket as shown in Figure 1 is subjected to plane strain that has…

A: Note: Dear Student! As per our guidelines, we are only allowed to answer three sub-parts of a…

Q: 5 -1 -1 If ɛ ij= -1 4 0 then principle strain values is -1 0 4 Ɛ; = 5,2,6 .1O E=3,2,6 .1I O Ej…

A: εij = εxxγxy2γxz2γyx2εyyγyz2γzx2γzy2εzz = 5-1-1-140-104

Q: Q The tensile tests were performed on longitudinal specimens of compact bone. The 0.0004 65 strain…

A: Strain is the deformation in the material per unit length. True strain is the natural log of the…

Q: (a) Due to a loading, the plate (ABCD) is deformed into the dashed shape shown in Fig. 1(a). the…

A: Given data: θ=60° Need to determine the average normal strain along the side AB and average shear…

Q: Calculate the longitudinal strain, if internal pressure is 1.2 N/mm2 and 1 m in diameter along with…

A: Given data: P=1.2 N/mm2d=1 mt=10 mmE=2×105 N/mm2μ=0.3 Need to determine the longitudinal strain.

Q: Question 5: The 45° strain rosette shown in Figure 5 is mounted on a machine element. The following…

Q: A thin square plate PQRS is symmetrically deformed into the shape shown by the dashed lines in the…

A: Given data: d=255 mmd1=256.1 mmd2=253.6 mm Need to determine the deformation in QS, normal strain in…

Q: (b) A 45° strain gauge rosette is attached to the surface of a steel plate and under a particular…

Q: The strains measured with a 60⁰ strain rosette are ϵa = R/3 x 10^-6 , ϵb= - R/2 x 10^-6 , and ϵc =…

A: Given data for 60o strain rosette, εa=R3×10-6εb=-R2×10-6εc=R8×10-6 The 60-degree strain rosette is…

Q: A 60° strain rosette is installed on the traction-free surface of a component with one of the strain…

A: *As per our guidelines we are supposed to answer first three sub-parts of the question. Kindly…

Question

The material distorts into the dashed position shown, where
d = 11 mm (Figure 1)
Determine the average normal strains ex, éy and the shear strain Yxy at A.
Part B
Determine the average normal strain along line BE.
Figure 1
• of 1
24
50 mm
B
200 mm
E
50 mm
A-
1 50 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An element of material in plain strain is subjected to strains x = 0.0015, , y . = -0.0002, and xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 20°. (b) Determine the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
An element of material in plain strain has the following strains: x = 0.001 and y = 0.0015. (a) Determine the strains for an element oriented at an angle = 250. (b) Find the principal strains of the element. Confirm the solution using Mohr’s circle for plane strain.
- 7.2-26 The strains on the surface of an experiment al device made of pure aluminum (E = 70 GPa. v = 0.33) and tested in a space shuttle were measured by means of strain gages. The gages were oriented as shown in the figure. and the measured strains were = 1100 X 106, h = 1496 X 10.6, and = 39.44 X l0_. What is the stress o in the x direction?
An element of material in plain strain is subjected to shear strain xy = 0.0003. (a) Determine the strains for an element oriented at an angle = 30°. (b) Determine the principal strains of the clement. Confirm the solution using Mohr’s circle for plane strain.
On the surface of a structural component in a space vehicle, the strains arc monitored by means of three strain gages arranged as shown in the figure. During a certain maneuver, the following strains were recorded: e, = 1100 X l0_6, 6h = 200 X lO_6, and e = 200 X 10-6. Determine the principal strains and principal stresses in the material. which is a magnesium alloy for which E = 6000 ksi and v = 0.35. Show the princ ipal strains and principal stresses on sketches of properly oriented elements.
Determine the strain energy per unit volume (units of psi) and the strain energy per unit weight (units of in ) that can be stored in each or the materials listed in the accompanying table, assuming that the material is stressed to the proportional limit. DATA FOR PROBLEM 2.7-5 Material Weight Density (lb/in3) Modulus of Elasticity (ksi) Proportional Limit (psi) Mild sleel 0.284 30,000 36,000 Tool steel 0.284 30,000 75,000 Aluminum 0.0984 10,500 60,000 Rubber (soft) 0.0405 0.300 300
Solve the preceding problem for an aluminum plate with h = 10 in.. i = 0.75 in., E = 10,600 ksi, v = 0.33. P = 96 kips. Pt,. = 24 kips. and V =18 kips. For part (b) of Problem 7.5-12, assume that the required strain energy stored is 640 in.-lb. In part (c). the change in volume cannot exceed 0.05%.
A thin square plate in biaxial stress is subjected to stresses ?? and ??., as shown in part a of the figure. The width of the plate is h = 12.0 in. Measurements show that the normal strains in the x and v directions are s = 427 × 10-6 and s = 113 × l0-6, respectively. With reference to part b of the figure. which shows a Iwo-dimensional view of the plate. determine the following quantities. (a) The increase .d in the length of diagonal Oil. (b) The change . in the angle between diagonal Oti and the x axis, (c) The shear strain y associated with diagonals Oil and cf(that is. find the decrease in angle ced).
A strain rosette (see figure) mounted on the surface of an automobile frame gives the following readings: gage A,310 × 10-6:gage B,180 × l0-6; and gage C. -160 × 10-6. Determine the principal strains and maximum shear strains, and show them on sketches of properly oriented elements.
The state of plane strain at a point has strain components of Px = -400(10-6), P y = 200(10-6), and gxy = 150(10-6), Fig. a. Determine the maximum in-plane shear strain and the absolute maximum shear strain.
On the free surface of an aluminum [E = 70 GPa;ν = 0.35]component, the strain rosette shown in Figure P13.42 was used toobtain the following normal strain data:εa = –300 με ,εb = 735 με,andεc = 410 με. Determine(a) the normal stressσ x .(b) the normal stressσ y .(c) the shear stressτxy .
If the normal strain is defined in reference to the final length Δs′, that is,P= = lim Δs′S 0 aΔs′ - Δs Δs′ b instead of in reference to the original length, Eq. 2–2, show that the difference in these strains is represented as a second-order term, namely, P - P= = P P′.