The member BD is attached to a rod at B, to a hydraulic cylinder at C, and to a fixed support at D. The bolt used at D acts in double shear and is made from a steel for which the maximum allowable shearing stress is Tallow= 40 ksi. The rod AB is made of a steel for which the maximum allowable tensile stress is Oallow = 60 ksi. The upward hydraulic force applied at C is 12 kip. 1) Calculate the minimum diameter of the rod AB. 2) Calculate the minimum diameter of the bolt at D. 12 kip

The member BD is attached to a rod at B, to a hydraulic cylinder at C, and to a fixed support at D. The bolt used at D acts in double shear and is made from a steel for which the maximum allowable shearing stress is Tallow= 40 ksi. The rod AB is made of a steel for which the maximum allowable tensile stress is Oallow = 60 ksi. The upward hydraulic force applied at C is 12 kip. 1) Calculate the minimum diameter of the rod AB. 2) Calculate the minimum diameter of the bolt at D. 12 kip

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The drive shaft AB of an automobile is made of a steel having allowable shear stress of tallow = 8 ksi. If the outer diameter of the shaft is 2.5 in. and the engine delivers 200 hp to the shaft when it is turning at 1140 rev>min, determine the minimum required thickness of the shaft’s wall.
The T-bracket is formed by welding together two cylindrical rods AB and CD. If the allowable shear stress is 80 MPa, what is the smallest allowable diameter of rod AB? Neglect the stress caused by the transverse shear force
the ends A and D of the two solid shafts AB and CD are fixed, while the ends B and C are connected to gears, as shown in the figure. Knowing that the maximum shear stress is 50 MPa in each axis, determine the maximum torque T that can be applied to gear B.
A compound steel (G = 70 GPa) shaft consists of a solid 59-mm-diameter segment (1) and a solid 39-mm-diameter segment (2). The allowable shear stress of the steel is 76 MPa, and the maximum rotation angle at the free end of the compound shaft must be limited to φC≤ 4.6°. Assume L1=0.6 m and L2=1.0 m. Determine the magnitude of the largest torque TC that may be applied at C. Express your answer in N-m rounded to three significant digits.
A flange-and-bolt coupling between two shafts carries 12 bolts at a pitch diameter of 18 in. The shafts carry a torque of 50,000 ft-lb. Assuming that this torque is transmitted by shear across the 12 bolts and that these bolts are to be designed for a shear stress s3 = 3,000 lb/sq in., what is the bolt diameter?
For the frame shown, a 4226-N load is acting on member ABD at D. If the allowable material shear stress for is 42 MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.
A solid steel shaft AB, shown in Fig. is to be used to transmit 5 hp fromthe motor M to which it is attached. If the shaft rotates at v = 175 rpm andthe steel has allowable shear stress of tallow = 14.5 ksi, determine therequired diameter of the shaft to the nearest 18 in.
For the riveted connection shown, the allowable shearing stress in the 25mm rivets is 140MPa. Assume the plates are adequate to transmit the load to the rivets. P = 60 kN.a. Determine the shearing stress in the most stressed rivet.b. Determine the maximum allowable value of P.c. If P = 80 kN, determine the minimum diameter of rivets.
The rigid beam BCD is attached by bolts to a control rod at B, to a hydraulic cylinder at C, and to a fixed support at D. The diameters of the bolts used are: dB = dD = 3/8 in., dC =1/2 in. Each bolt acts in double shear and is made from a steel for which the ultimate shearing stress is τU = 40 ksi. The control rod AB has a diameter dA=7/16 in. and is made of a steel for which the ultimate tensile stress is σU = 60 ksi. If the minimum factor of safety is to be 3.0 for the entire unit, determine the largest upward force that may be applied by the hydraulic cylinder at C.
2. The puncher is to drive a 25 mm diameter hole to a steel plate. If the allowable axial stress of the puncher is limited to 101.85 MPa, determine the thickness (t) of the steel plate. The maximum shear stress of the steel plate is 50MPa.
Since each of the shafts AB, BC and CD shown in the figure consists of a solid circular bar, determine the magnitude of the stress in the shaft (MPa) at which the maximum shear stress occurs.
The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. The modulus of rigidity is 3.7 × 106 psi for aluminum and 5.6 × 106 psi for brass. Take T = 13 kip·in. a) Determine the maximum shearing stress in cylinder AB. b) Determine the maximum shearing stress in cylinder BC.