The metal plate has the constant temperature shown on its boundaries. Find the equilibrium temperature at each of the indicated interior points by setting up a system of linear equations and obtain a solution by applying either the Gauss elimination or the Gauss Jordan elimination method. 40° 0° 40° 12 t3 0° 40° t4 t5 t6 0° 40° 5° 5° 5°

The metal plate has the constant temperature shown on its boundaries. Find the equilibrium temperature at each of the indicated interior points by setting up a system of linear equations and obtain a solution by applying either the Gauss elimination or the Gauss Jordan elimination method. 40° 0° 40° 12 t3 0° 40° t4 t5 t6 0° 40° 5° 5° 5°

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The answer will be 733.16KN, 1.85 m Show complete solution and draw each step by step.
Coplanar force equilibrium Pls do step by step Answer F=363.9N
1. A Carnot engine requires 35 kJ/sec from the hot source. The engine produces 15 kW of power and the temperature of the sink is 26°C. What is the temperature of the hot source? The answer is 523.25 K, show the complete solution and draw a diagram.
Read the question carefully and give me right solution according to the question. Note: Don't copy other expert solution. I have other website solution. A metallic ball of radius ro = 5 mm, is initially in equilibrium at 400 C in a furnace. It is suddenly dropped to water at 20 C hw 10814 W/m2 K, . The properties of the sphere are density= 3000 kg/m3, k = 20 W/m_ K, c = 1000 J/kg K, and α= 6.66E-6 m2/s. Calculate the time required for the center of the sphere to cool to 50 C.
A insulating cylinder has an equal amount of gas on both sides of a movable piston, as shown inthe above figure. Initially, the two compartments have equal volumes and their temperaturesare 550 K and 250 K. The piston then moves slowly until it comes to rest at an equilibriumposition. Find the final temperatures in the two portions.
A 0.1 kg block of pure copper at a temperature of 250°C is dropped into a 4°C water bath. The bath contains 0.03 m^3 of water and is well insulated. Find the final temperature after the block and the water reach thermal equilibrium. (It is reasonable to assume the following: the specific heat of water is equal to the value at 4°C; the specific heat of the material in the block can be taken to be a constant value evaluated at a temperature mid-way between the initial temperatures of the block and the water.)
A mass of ice at -7 C is needed to cool 224 kg of vegetables (Cp = 3.35 KJ /kg.K )in a bunker for 24 hours. The initial temperature of the vegetables is assumed to be 29 C . It is also assumed that the average temperature in the bunker is 7C within the 24 -hour period . If the heat gained per hour in the bunker is 25% of the heat removed to the vegetables from 29 C to 7C, what would be the required mass of ice ? show t-s diagram
The instruction booklet for your pressure cooker indicates that its highest setting is 11.3 psipsi . You know that standard atmospheric pressure is 14.7 psipsi, so the booklet must mean 11.3 psipsi above atmospheric pressure. At what temperature in degrees Celsius will your food cook in this pressure cooker set on "high"? use the Clausius-Clapeyron equation
A metal plate with a width of the base is located on the positive x-axis. The plate extends along the positive y-axis with infinite length. The base plate is given a temperature of T = x⁰ while the temperature of the plate on the other three sides is maintained at 0⁰. Determine the temperature of each point on the metal, T(x,y).
The cylinder CD of the assembly is heated from T1 = 30°C to T2 = 180°C using electrical resistance. At the lower temperature T1 the gap between C and the rigid bar is 0.7 mm. Determine the force in rods AB and EF caused bythe increase in temperature. Rods AB and EF are made of steel, and each has a cross-sectional area of 125 mm2. CD is made of aluminum and has a cross-sectional area of 375 mm2. Est = 200 GPa, Eal = 70 GPa, and aal = 23(10-6)>°C.
Two spheres each 3.0ft in diameter are connected by a pipe in which there is a valve. Each sphere contains nitrogen gas with sphere A has a temperature of 80°F, while the other is 120°F. With the valve closed, sphere A has a gauze pressure of 51.9 psi and the other 10.9 psi. After the valve has been open long enough for equilibrium to obtain, what is the equilibrium temperature if the final pressure is 35.2 psig?
14. A commonly used method of fastening one part to another part iscalled “shrink fi tting.” A steel rod has a diameter of 2.0026 cm, and afl at plate contains a hole whose diameter is 2.0000 cm. The rod is cooledso that it just fi ts into the hole. When the rod warms up, the enormousthermal stress exerted by the plate holds the rod securely to the plate. Byhow many Celsius degrees should the rod be cooled?