The moment of inertia of a pair of locomotive driving wheels with the axle is 150 kg.m². The distance between the wheel centres is 1.2 m and the diameter of the wheel treads is 2m. Due to defective ballasting one wheel falls by 5 mm and raises again in a total time of 0.2 seconds while the locomotive travels on a level track at 100 kmph. Assuming that the displacement of the wheel takes place with simple harmonic motion about mid point of total fall. Determine the gyroscopic couple produced. Hint: Consider this motion as pitching motion in ship. Draw free body diagram of each link for the following figure 44. 75° D 200 mm 250 N AD-150mm BC-AD-500mm DC-300mm [F450mm

The moment of inertia of a pair of locomotive driving wheels with the axle is 150 kg.m². The distance between the wheel centres is 1.2 m and the diameter of the wheel treads is 2m. Due to defective ballasting one wheel falls by 5 mm and raises again in a total time of 0.2 seconds while the locomotive travels on a level track at 100 kmph. Assuming that the displacement of the wheel takes place with simple harmonic motion about mid point of total fall. Determine the gyroscopic couple produced. Hint: Consider this motion as pitching motion in ship. Draw free body diagram of each link for the following figure 44. 75° D 200 mm 250 N AD-150mm BC-AD-500mm DC-300mm [F450mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flywheel connected to a punching machine has to supply energy of 400 Nm while running at a mean angular speed of 20 radians/s. If the total fluctuation of speed is not to exceed ±2%, the mass moment of inertia of the flywheel in kg – m2 is
In order to determine the mass moment of inertia of a flywheel of radius 600 mm, a 12-kg block is attached to a wire that is wrapped around the flywheel. The block is released and is observed to fall 3 m in 4.6 s. To eliminate bearing friction from the computation, a second block of mass 24 kg is used and is observed to fall 3 m in 3.1 s. Assuming that the moment of the couple due to friction remains constant, determine the mass moment of inertia of the flywheel.
A multi bladed turbine disc can be assumed to have a combined mass of 150kg with an effective radius of gyration of 0.59m. The disc is rigidly attached to a steel shaft 2.4m long and, under service conditions, rotates at a speed of 250 rev/min. Determine the diameter of the shaft required in order that the maximum shear stress set up in the event of sudden seizure of the shaft shall not exceed 200 MN/m^2. Neglect the inertia of the shaft itself and take the modulus of rigidity G of the shaft material to be 85 GN/m^2.
A yoyo is constructed by attaching three uniform, solid disks along their central axes as shown. The two outer disks are identical, each with mass M = 58 g, radius R = 3.3 cm, and moment of inertia 1/2MR2. The central, smaller disk has mass M/2 and radius R/2. A light, flexible string of negligible mass is wrapped counterclockwise around the central disk of the yoyo. The yoyo is then placed on a horizontal tabletop and the string is gently pulled with a constant force F = 0.25 N. The tension in the string is not sufficient to cause the yoyo to leave the tabletop. In this problem consider the two cases show. In Case 1 the string is pulled straight up, perpendicular to the tabletop. In Case 2 the string is pulled horizontally, parallel to the tabletop. In both cases the yoyo rolls without slipping. In both the cases shown what is the magnitude of the tourqe t excerted by the string about the contact point of the yo-yo wiith the table in N*m. What is the moment of intertia of the yo-yo…
A flywheel of mass 0.9 ton is fitted to a multi cylinder engine, which runs at a mean speed of 380 r.p.m. If the speed varies from 9 % above the mean to 6 % below it and the fluctuation energy is 1100 kN-cm, find (i) mass moment of inertia of the wheel and (ii) radius of Gyration.
The pendulum consists of the 4-kgkg slender rod and the 5.5-kgkg thin plate. Suppose that aaa = 1.5 mm , bbb = 0.5 mm , and hhh = 2.4 mm A: Determine the location of the center of mass G of the pendulum. B: Determine the mass moment of inertia of the pendulum about an axis perpendicular to the page and passing through G.
Two disks A and B, of mass m 1 kg each and of radius 10 cm, are placed on a horizontal table. The disk A is launched in translation with a speed of 10 m/s along the y axis, B is at rest. The coefficient of kinetic friction between the disks is 0.5. The line of impact is at an angle of 60° with the x-axis. The moment of inertia of each disk around its center of mass is I = 1₂ = 0.005 kg.m². The coefficient of restitution between the two disks is e=0.6. a) Determine the velocities of the centers of the two disks, just after the impact. b) Calculate the angular velocities of the disks, just after the impact. c) Calculate the energy loss during the impact.
Consider a cube with mass m and side a. (a) Show that the ellipsoid of inertia at the center of the cube is a sphere, and use this property to determine the moment of inertia of the cube with respect to one of its diagonals. (b) Show that the ellipsoid of inertia at one of the corners of the cube is an ellipsoid of revolution, and determine the principal moments of inertia of the cube at that point.
To increase the wheel's moment of inertia, I mount a thin hoop of mass m =2.11kg to its rim, then restart it spinning at the same rate. The precession speed decreases to Ω(1)=1.21s^−1. What is the mass of the wheel without the hoop?
Two blocks are attached by strings of negligible mass to a physical pulley with two radii R1=027 m and R2=042 m. The strings are wrapped around their respective radii so that the masses can move either up or down. The pulley has a moment of inertia Ipcm=0249 kgm2, and is supported by a bearing with negligible friction. If block 1 has a mass of m1=4.1 kg, block 2 has a mass of m2=1.14 kg, and the tension in the rope connecting block 1 to the pulley is T1p=31.11 N, what is the magnitude of the angular acceleration of the pulley?
A flywheel of mass 10 kg and radius of gyration 200 mm is spinning about its axis, which is horizontaland is suspended at a point distant 150 mm from the plane of rotation of the flywheel. Determine theangular velocity of precession of the flywheel. The spin speed of flywheel is 900 r.p.m.
The rotor of an electric motor has a mass of 25 kg, and it is observed that 4.2 min is required for the rotor to coast to rest from an angular velocity of 3600 rpm. Knowing that kinetic friction produces a couple of magnitude 1.2 N.m, determine the centroidal radius of gyration for the rotor.