The motor A delivers 7500 kW to the shaft at 3600 rev/min, of which 2500 kW is removed by gear B and 5000 kW is removed by gear C. Determine (a) the maximum shear stress in the shaft; and (b) the angle of twist of end D relative to end A. Use G = 83 GPa for steel, and assume that friction at bearing D is negligible. 125 mm 100 mm 100 mm A D В C 1.5 m 1.0 m - 0.5

The motor A delivers 7500 kW to the shaft at 3600 rev/min, of which 2500 kW is removed by gear B and 5000 kW is removed by gear C. Determine (a) the maximum shear stress in the shaft; and (b) the angle of twist of end D relative to end A. Use G = 83 GPa for steel, and assume that friction at bearing D is negligible. 125 mm 100 mm 100 mm A D В C 1.5 m 1.0 m - 0.5

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. 1.) Determine the maximum shear stress in the shaft in ksi. (Answer in 2 decimal places) 2.) Determine the angle of twist in degrees of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible. (Answer in 3 decimal places)
Q: Part A: Determine the absolute maximum shear stress in the shaft. Part B: Determine the angle of twist of end EE of the shaft relative to BB. Given: The turbine develops 150 kW of power, which is transmitted to the gears such that CC receives 70% and DD receives 30%. The rotation of the 100-mm diameter A-36 steel shaft is ωomega = 600 rev/min . The journal bearing at EE allows the shaft to turn freely about its axis. The shear modulus of elasticity for A-36 steel is 75 GPa.
A three-thread worm gear, rotating at 1000 rpm, drives a 31-tooth worm gear and transmit 15 HP. Theworm has 14 ½ o teeth with ¾ pitch, 2 in pitch diameter, and an included face angle of 60o. The coefficientof friction is 0.05. (Assume Y = 0.322) A. Determine the helix angle of the worm. Ans. 70.30o B. Determine the speed ratio. Ans. 10.33C. Determine the center distance. Ans. 4.70 inD. Determine the apparent stress in the worm wheel teeth. Ans. 31,100 psiE. Determine the efficiency of this worm-gear set. Ans. 85.70%
The connecting rod of a four stroke cycle Diesel engineis of circular section and of length 550 mm. The diameter and stroke of the cylinder are 150 mm and240 mm respectively. The maximum combustion pressure is 4.7 N/mm2. Determine the diameter ofthe rod to be used, for a factor of safety of 3 with a material having a yield point of 330 MPa.Find also the maximum bending stress in the connecting rod due to whipping action if the engine runsat 1000 r.p.m. The specific weight of the material is 7800 kg/m3. [Ans. 33.2 mm ; 48 MPa]
A generator driven by a wind turbine is required to deliver 5 MW of power at the generator terminals. The turbine is a two-blade propeller rotating about a horizontal axis and the maximum permitted shear stress of the turbine shaft is 55x106 N/m2 The rotor is designed to operate at a rotational speed of 45 revolution per seconds .The stage efficiencies are Cp 0.32, ngb = 0.90, ng = 0.92. %3D . (i) If the turbine delivers its rated power at a wind average speed of 22 m/s, calculate the corresponding diameter of the propeller and its TSR, assuming a typical value for the overall efficiency. The air density may be assumed to have a value 1.29 kg/m³. (ii) Calculate the torque on the turbine shaft.
1.1. State three underlying assumptions in the formulation of the torsion formula, .TGJrl (3) 1.2 A hollow shaft has to be designed for a marine engine delivering 1200 kW when running at 120 r/min. The maximum allowable shear stress is 50 MPa and the maximum torque to be transmitted by the shaft is 30 % greater than the mean torque. The internal diameter of the shaft is 50 % that of the external diameter. Calculate: 1.2.1 The dimensions of the shaft and the angle of twist of the shaft over 3 m when transmitting the above torque (G = 80 GPa). (14) 1.3 Determine the torsional rigidity of a 300 mm long steel shaft with a diameter of 50 mm. (G = 80 GPa
The motor delivers 65 hp to the A36 steel shaft while it rotates at 1500 RPM. The shaft is supported on smooth bearings at B and E, which allow free rotation of the shaft. The gears C and D fixed to the shaft remove 70% and 30% of the power delivered by the motor, respectively. Determine the diameter of the shaft to the nearest 1/8 in. if the allowable shear stress is ττallow = 12 ksi and the allowable angle of twist of D with respect to A is 0.25 degrees.
Q1) The mean diameter of the driving pulley for a vee-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of friction between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm2.
The shaft below is made of A992 steel and has an allowable shear stress of tadm = 75 MPa. When the shaft is rotating at 300 rpm, the motor provides 8 kW of power, while gears A and B draw 5 kW and 3 kW, respectively. Determine the minimum diameter required for shaft. Also, find the angle of twist of the gear A with respect to C.
In which option the place and value of the maximum stress that will occur in the ABCD stepped shaft to which the pulleys are connected by the effect of torsional moments is given correctly. All parts of the shaft are filled. The shaft rotates at a constant angular speed. TA = 45Nm, TB= 15Nm, TD = 20Nm, d1= 20mm , d2= d3 =24mm pi = 3
When drilling a well at a constant angular velocity, the bottom end of the drill pipe encounters a torsional resistance TA. Also, soil along the sides of the pipe creates a distributed frictional torque along its length, varying uniformly from zero at the surface B to tA at A. Determine the minimum torque TB that must be supplied by the drive unit to overcome the resisting torques, and calculate the maximum shear stress in the pipe. The pipe has an outer radius ro and an inner radius ri.
The shaft shown below consists of three segments AB, BC and CD is subjected to the three torques T1=114 N.m, T2=245 N.m and T3=441 N N.m. The length of each segment is L1=0.71 m, L2=0.31 m and L3=0.43 m . The diameter of each segment is d1=46 mm, d2=97 mm and d3=131 mm . The material have modulus of rigidity G = 143 Gpa. Answer the following questions