The turbine develops 150 kW of power, which is transmitted to the gears such that C receives 70% and D receives 30%. The rotation of the 100-mm-diameter A-36 steel shaft is w = 600 rev/min. The journal bearing at E allows the shaft to turn freely about its axis. The shear modulus of elasticity for A-36 steel is 75 GPa. (Figure 1) Part A Determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. ? Tmax = 38.197 GPa Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining Part B Determine the angle of twist of end E of the shaft relative to B. Express your answer using three significant figures. vec DE/B = rad Submit Request Answer Provide Feedback Next > Figure < 1 of 1 m

The turbine develops 150 kW of power, which is transmitted to the gears such that C receives 70% and D receives 30%. The rotation of the 100-mm-diameter A-36 steel shaft is w = 600 rev/min. The journal bearing at E allows the shaft to turn freely about its axis. The shear modulus of elasticity for A-36 steel is 75 GPa. (Figure 1) Part A Determine the absolute maximum shear stress in the shaft. Express your answer to three significant figures and include the appropriate units. ? Tmax = 38.197 GPa Submit Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining Part B Determine the angle of twist of end E of the shaft relative to B. Express your answer using three significant figures. vec DE/B = rad Submit Request Answer Provide Feedback Next > Figure < 1 of 1 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.12P

See similar textbooks

Similar questions

The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. 1.) Determine the maximum shear stress in the shaft in ksi. (Answer in 2 decimal places) 2.) Determine the angle of twist in degrees of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible. (Answer in 3 decimal places)
A solid steel shaft ABCDE turns freely in bearings at points A and E. The shaft is driven by the gear at C,which applies a torque T2 = 325lb−ft. Gears at B and D are driven by the shaft and have resisting torquesT1 = 200lb − ft and T3 = 125lb − ft, respectively. Segments BC and CD have lengths LBC = 20 in. andLCD = 15 in. and the shear modulus G = 11, 600ksi. Determine the minimum required diameter (d) ofthe shaft if the allowable shear stress τa = 6ksi. Also calculate the angle of twist between gears B and D.
Determine the diameter of a solid steel shaft which will transmit 112.5 kW at 200 rpm. Also determine the length of the shaft if the twist must not exceed 1.5o over the entire length. The maximum shear stress is limited to 55 N/mm2. Take the value of modulus of rigidity = 8 x 104 N/mm2.
The solid steel shaft is supported by frictionless bearings in D and E. This system is connected to a motor that provides 5 kW of power to the shaft while rotating at w = 75 rpm. If A and B gears get 2 kW and 3 kW respectively, determine the minimum shaft diameter. w rotation speed and safety shear stress τem = 35MPa are known and given in the table with your names below.
The shaft ABC shown in the figure is drivenby a motor that delivers 300 kW at a rotational speedof 32 Hz. The gears at B and C take out 120 kW and180 kW, respectively. The lengths of the two parts ofthe shaft are L1 = 1.5 m and L2 = 0.9 m.Determine the required diameter d of the shaft ifthe allowable shear stress is 50 MPa, the allowableangle of twist between points A and C is 4.0°, andG = 75 GPa.
Determine the diameter of a solid steel shaft that will transfer 30 MW at 1500 RPM with a 1 degree twist angle for every 20 diameters of length. G=80GN/m2. Give me the solution of this please. Ans. D = 3.03 m
A hollow steel shaft of length 1.75 m transmits 2000 kW of power at a speed of150 rev/min. The inside diameter is to be 0.75 times the outside diameter. Themaximum allowable torsional shear stress for the steel is 130 MN/m2and themodulus of rigidity (G) for the steel is 83 GN/m2. Given that a factor of safety of2 is required for the shaft, determine:i) the torque acting on the shaft;ii) the required external and internal diameters for the shaft; iii) the torsional shear stress set-up in the shaft material at the inside surfaceof the hollow shaft, and sketch the stress distribution through the shaftwall;iv) the angle of twist (in degrees) due to the torque.
A generator driven by a wind turbine is required to deliver 5 MW of power at the generator terminals. The turbine is a two-blade propeller rotating about a horizontal axis and the maximum permitted shear stress of the turbine shaft is 55x106 N/m2 The rotor is designed to operate at a rotational speed of 45 revolution per seconds .The stage efficiencies are Cp 0.32, ngb = 0.90, ng = 0.92. %3D . (i) If the turbine delivers its rated power at a wind average speed of 22 m/s, calculate the corresponding diameter of the propeller and its TSR, assuming a typical value for the overall efficiency. The air density may be assumed to have a value 1.29 kg/m³. (ii) Calculate the torque on the turbine shaft.
The propellers of a ship are connected to an A-36 steel shaft that is 60 m long and has an outer diameter of 340 mm and inner diameter of 260 mm. If the power output is 4.5 MW when the shaft rotates at 20 rad/s, determine themaximum torsional stress in the shaft and its angle of twist.
A keyed gears delivers a torque of 912.4 N-m thru its shaft of 63.5 mm outside diameter. If the key has thickness of 15.875 mm and width of 11.1125 mm, find the length of the key. Assume permissible stress value of 61.2 MPa for shear and tension at 99.8 MPa
The solid steel shaft DF has a diameter of 25 mm and is supported by smooth bearings at D and E. It is coupled to a motor at F, which delivers 12 kW of power to the shaft while it is turning at 50 rev>s. If gears A, B, and C remove3 kW, 4 kW, and 5 kW respectively, determine the maximum shear stress in the shaft within regions CF and BC. The shaft is free to turn in its support bearings D and E.
tubular steel [G = 80 GPa] shaft is being designed to transmit 150 kW at 30 Hz. The maximum shear stress in the shaft must not exceed 80 MPa and the angle of twist is not to exceed 6° in a 4-m length. Determine the minimum permissible outside diameter if the ratio of the inside diameter to the outside diameter is 0.80.