The net radiant-heat exchange between a 20-by-20 ft rough plaster panel-heated ceiling and a 20-by-10-ft side wall, which has an emissivity of 0.80, is 2400 Btu/hr. If the surface temperature of the ceiling is 120 deg. F, determine the average surface temperature of the side wall.
Q: At winter design conditions, a house is projected to lose heat at a rate of 60,000 Btu/h. The…
A: Given data heat loss at a rate of =60000 Btu/h. internal heat gain=6000 Btu/h.To determine…
Q: Question # 2: A10-m-long section of a 6-cm-diameter horizontal hot water pipe passes through a large…
A: Given data as per the question Length of section =10 m diameter =6 cm Tmean=65+222=43.50cconsidering…
Q: The components of an electronic system dissipating 180 W are located in a 1.4-m-long horizontal duct…
A:
Q: How much air is used per kg of coal boiler having a chimney of 35 m height to create draft of 20 mm…
A: The answer is in next step
Q: A fan is to accelerate quiescent air to a velocity of 8 m/s at a rate of 9 m3 /s. Determine the…
A: Given: The velocity of the quiescent air is v=8 m/s The volume rate of the quiescent air is V=9 m3/s…
Q: 1. Ammonia with a specific volume of 1.94 m³ /kg flows at a rate of 3.3 kg/s through a tube with a…
A: As per our guidelines we are supposed to answer only one question. Kindly repost other questions as…
Q: If q" w = 5000 and the convection heat transfer coefficient at the pipe outlet is 1000 W/m2K,…
A:
Q: Consider a person who is trying to keep cool on a hot summer day by turning a fan on and exposing…
A: Write the given information. Write the properties of air at 100°F.
Q: air at a dry ball temperature of 80 degrees C and 4% RH is passed over the cooling coil so that the…
A: Condition of air at state 1, =80oC and 4% RH Temperature of air after cooling,=35oC
Q: Consider an airplane cruising at an altitude of 10 km where Standard atmospheric conditions are…
A: Given dataDimensions Lxw=25x3H=10 kmV=800 kmhCf=0.001bP=26.5 KPaT=-50°C
Q: What are the best possible solutions to increase the heat transfer rate of a body?
A: There are three modes of heat transfer; Conduction, convection and radiation. For these all modes we…
Q: A10-m-long section of a 6-cm-diameter horizontal hot water pipe passes through a large room whose…
A:
Q: A Gasoline engine operating on an air standard condition has a clearance volume of 15cm3 and a…
A:
Q: A fan is to accelerate quiescent air to a velocity of 10 m/s at a rate of 4 m3/s. Determine the…
A: Giventhe volume flow rate of tha fanv=4m3/svelocity of air caused by fanV=10m/sthe density of air…
Q: What are the mechanisms of heat transfer? How are they distinguished from each other?
A: There are three mechanisms of heat transfer. These are given as under, (1) Conduction (2) Convection…
Q: 800 W/mlof radiant energy is incidert upon a surface, out of which B00 transmissivity (T S 103 rete…
A:
Q: The space in a small building with average construction quality is to be provided with ventilation…
A: Write the expression of number of air changes per hour.
Q: The hot water needs of a household are to be met by heating water at 15°C to 95°C by a parabolic…
A:
Q: A 2-kW baseboard electric resistance heater in a vacant room is turned on and kept on for 15 min.…
A:
Q: A 18-m-long section of a 14-cm-diameter horizontal hot water pipe passes through a large room whose…
A:
Q: In a power plant, pipes transporting superheated vapor are very common. In a certain plant,…
A: Given data as per question Mass flow rate =0.3 kg/s Inside diameter = 5 cm = 0.05 m Length of pipe =…
Q: A fan is to accelerate quiescent air to a velocity to 12 m/s at a rate of 3 m3/min. If the density…
A:
Q: The components of an electronic system dissipating 150 W are located in a 1-m-long horizontal duct…
A: (a) The temperature at the inlet of the duct, The temperature at the outlet of the duct, The…
Q: The components of an electronic system dissipating 180 W are located in a 4-ft-long horizontal duct…
A: The data given is Temperature inlet, Tin = 85°F Temperature inlet, Tout = 100°F Area of cross…
Q: 25 W/m. C. Determine the rate of heat transfer from the surface for a Ix0.5 m section of the plate.…
A:
Q: The temperature at the inner and outer surfaces of a boiler wall made of 25 mm thick steel and…
A: solutiongiven dataTi=350°CT∘=600°Cb1=25 mmb2=15 mmks=68 w/m°CKins=0.126 w/m°C
Q: Determine the steady rate of heat transfer
A:
Q: Problem 2 A vertical piston-cylinder device contains water and is being heated on top of a range.…
A:
Q: Portable electric heaters are commonly used to heat small rooms. Explain the energy transformation…
A: Given:1st Law of thermodynamics: According to this law, total energy of the system is conserved,It…
Q: A 2-kW resistance heater wire with thermal conductivity of k = 20 W/m - C, a diameter of D =5 mm,…
A: Given data as per the question thermal conductivity = 20 W/m · °C diameter = 5 mm length = 0.7 m…
Q: The condenser of a steam power plant operates at a pressure of 7.38 kPa (Tsat = 40°C) steam at this…
A: Givendia of pipe D=0.03mSurface temp ts=30°Csteam temp=40°Cmean temp of film above tube…
Q: The hot water needs of a household are to be met by heating water at 15°C to 95°C by a parabolic…
A: Entry temperature = 15 C Exit temperature = 95 C flow rate = 1.8 kg/s Diameter = 4 cm Net…
Q: Air with a temperature of 128 °C, a density of 4.89 kg/m3 and a velocity of 121 m/s enters a nozzle…
A: The mass flowrate of fluid passing through a cross section can be determined as the product of…
Q: An average person body surface is approximately 2.0 m². Its skin temperature is 33°C. The convection…
A: Find convective heat transfer .
Q: determine the efficiency of the heat transfer process if a dry air parcel is heated by the earths…
A:
Q: A Gasoline engine operating on an air standard condition has a clearance volume of 15cm^3 and a…
A: Given data Clearance volume = 15 cm³ Displacement volume = 100 cm³
Q: what are the different modes of heat transfer? Explain transfer of heat by convection process?
A:
Q: (b) An airplane is flying at 1000 km/h through a still air having a pressure and temperature of 78.5…
A: Given data: V=1000 km/h=277.77 m/sP0=78.5 kN/m2T0=-8°C=265 KR=287 J/kg.Kγ=1.4 Need to determine the…
Q: A 110-volt 6 Ampere electric heatrer is submerged in 1 kg of water for 24 minutes. What will be the…
A: Calculate the power generated by the electric heater during its use. Pin=VI Here, Pin is the power…
Q: The components of an electronic system dissipating 150W are located in a 1-m-long horizontal duct…
A: (a) The temperature at the inlet of the duct, The temperature at the outlet of the duct, The…
Q: Conceptually, what is the integral of heat transfer rate, Q dot?
A:
Q: An automobile engine consumes fuel at a rate of 22 L/h and delivers 55 kW of power to the wheels. If…
A: Given, Fuel's volumetric consumption rate = V' = 22 L/h = 22×10-33600 m3/s Heating value of fuel =…
Q: An aluminum pan whose thermal conductivity is 237 W/m*^ C has a flat bottom whose diameter is 20 cm…
A: Given-Data:- Thermal Conductivity=237Wm°CThickness of aluminium pan(L)=0.6cmDiameter of Aluminium…
Q: Define the energy content of a control volume can be changed by mass flow as well as by heat and…
A: Consider a control volume exchanging heat Q as well as work W with the surroundings. Also certain…
Q: 7-34 An array of power transistors, dissipating 5 W of power each, are to be cooled by mounting them…
A: Determine the average film temperature by using the information given in the question. Here, Ts is…
Q: An average man has a body surface area of 1.8 m2 and a skin temperature of 330C. The convective…
A: Let A = Surface area of man body =1.8m2 V =1.2m/s h =Heat Transfer Coefficient =8.6XVX0.53 h…
Q: The heat is dissipated from the plate by convection and radiation into surrounds at 20 C . Take ε…
A: Given Ta=20 0C=20+273.15 K=293.15 KTs=50 0C=50+273.15 K=323.15 K ε=0.8σ=5.67×10-8 Wm2K4h=6 W/m2K
The net radiant-heat exchange between a 20-by-20 ft rough plaster panel-heated ceiling and a 20-by-10-ft side wall, which has an emissivity of 0.80, is 2400 Btu/hr. If the surface temperature of the ceiling is 120 deg. F, determine the average surface temperature of the side wall.
Step by step
Solved in 2 steps with 3 images
- 7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?The velocity profile in fully developed laminar flow in a circular pipe, in m/s, is given by u(r) = 6(1 - 100r2), where r is the radial distance from the centerline of the pipe in m. Determine (a) the radius of the pipe, (b) the average velocity through the pipe, and (c) the maximum velocity in the pipe.The chilling room of a meat plant is 15 m × 18 m × 5.5 m in size and has a capacity of 350 beef carcasses. The power consumed by the fans and the lights in the chilling room are 22 and 2 kW, respectively, and the room gains heat through its envelope at a rate of 14 kW. The average mass of beef carcasses is 220 kg. The carcasses enter the chilling room at 35C, after they are washed to facilitate evaporative cooling, and are cooled to 16°C in 12 h. The air enters the chilling room at 2.2°C and leaves at 0.5°C. Determine (a) the refrigeration load of the chilling room and (b) the volume flow rate of air. The average specific heats of beef carcasses and air are 3.14 and 1.0 kJ/kg · °C, respectively, and the density of air can be taken to be 1.28 kg/m3 .
- An average man has abody surface area of 1.8m2 and a skin temperature of 33degrees celcius .The convection heat transfer coefficient for a clothed person walking in still air is expressed as {h,8.6V^0.53}FOR 0.5<v<2m/s,where V is the walking velocityin m/s.Assuming the average surface temperature of the clothed person to be 30degrees celcius, determine the rate of heat loss from an average man walking in still air at 10degrees celcius by convectionat a walking velocity of (a)0.5m/s (b)1.0m/s (c)1.5m/s (d)2.0m/sWater is to be heated from 15°C to 65°C as it flows through a 3-cm-internaldiameter 5-m-long tube . The tube is equipped with an electric resistance heater that provides uniform heating throughout the surface of the tube. The outer surface of the heater is well insulated, so that in steady operation all the heat generated in the heater is transferred to the water in the tube. If the system is to provide hot water at a rate of 10 L/min, determine the power rating of the resistance heater. Also, estimate the inner surface temperature of the tube at the exit.air at a dry ball temperature of 80 degrees C and 4% RH is passed over the cooling coil so that the temperature of the air dry ball becomes 35 degrees Celsius. how much heat is released from the air in the process? (answer in kj / kg)
- A Gasoline engine operating on an air standard condition has a clearance volume of 15cm3 and a displacement volume of 100cm3 . Determine the theoretical thermal efficiency of the engine.Consider an air solar collector that is 1 m wide and 5 m longand has a constant spacing of 3 cm between the glass cover andthe collector plate. Air enters the collector at 30°C at a rate of0.15 m3/s through the 1-m-wide edge and flows along the 5-mlong passage way. If the average temperatures of the glasscover and the collector plate are 20°C and 60°C, respectively,determine (a) the net rate of heat transfer to the air in thecollector and (b) the temperature rise of air as it flows throughthe collector.The blades of a wind turbine turn a large shaft at a relatively slow speed. The rotational speed is increased by a gearbox that has an efficiency of 0.93. In turn, the gearbox output shaft drives an electric generator with an efficiency of 0.95. The cylindrical nacelle, which houses the gearbox, generator, and associated equipment, is of length L = 6 m and diameter D = 3 m. If the turbine produces P = 2.5 MW of electrical power, and the air and surroundings temperatures are T = 25 oC and Tsur = 20 oC, respectively, determine the minimum possible operating temperature inside the nacelle. The emissivity of the nacelle is 0.83, and the convective heat transfer coefficient is h = 35 W/m2 .K. The surface of the nacelle that is adjacent to the blade hub can be considered to be adiabatic, and solar irradiation may be neglected. Use Fin or N number of fins to reduce the Ts of the nacelle less than 143 oC
- An average man has a body surface area of 1.8 m2 and a skin temperature of 330C. The convective heat transfer coefficient for a clothed person walking in still air is expressed as h= 8.6V0.53 where V is the walking velocity in m/s. Assuming the average surface temperature of the clothed person to be 300C, determine the rate of heat lost by convection from an average man walking in still air at 100C at a walking velocity of 1.2 m/s.It is well known that the power consumed by a compressor can be reduced by cooling the gas during compression. Inspired by this, somebody proposes to cool the liquid as it flows through a pump, in order to reduce the power consumption of the pump. Would you support this proposal? Explain.The components of an electronic system dissipating 180 W are located in a 4-ft-long horizontal duct whose cross section is 6 in * 6 in. The components in the duct are cooled by forced air, which enters at 85°F at a rate of 22 cfm and leaves at 100°F. The surfaces of the sheet metal duct are not painted, and thus radiation heat transfer from the outer surfaces is negligible. If the ambient air temperature is 80°F, determine (a) the heat transfer from the outer surfaces of the duct to the ambient air by natural convection and (b) the average temperature of the duct. Evaluate air properties at a film temperature of 100°F and 1 atm pressure. Is this a good assumption?