Please answer it in 1hr.Thermodynamics First Law of Thermodynamics Conservation MassShow solution step by step.1. Ammonia with a specific volume of 1.94 m³ /kg flows at a rate of 3.3 kg/s through atube with a cross sectional area of 0.01m². Determine the average velocity across thetube cross section.Answer: 640.2 m/s2. Oil, with a specific gravity of 0.9, enters a pump with a volumetric flow rate of 0.1m³ /min through a 10 cm pipe at 20 °C. the diameter of the exit pipe is 7 cm and the flowis isothermal.a. the mass flow rate in kg/s.b. the inlet velocity in m/s; andc. the exit velocity, in m/sAns: m = 1.5 kg/s; Vin = 0.2122 m/s; Vout = 0.433 m/s

As per our guidelines we are supposed to answer only one question. Kindly repost other questions as…

1. Ammonia with a specific volume of 1.94 m³ /kg flows at a rate of 3.3 kg/s through a tube with a cross sectional area of 0.01m². Determine the average velocity across the tube cross section. Answer: 640.2 m/s

1. Ammonia with a specific volume of 1.94 m³ /kg flows at a rate of 3.3 kg/s through a tube with a cross sectional area of 0.01m². Determine the average velocity across the tube cross section. Answer: 640.2 m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Given data : m=10 kg V=22 m/s Determine kinetic energy

A: Given data, m= 10 kg v= 22 m/s

Q: Q4 (a) For each of the topics below, give ONE example demonstrates the application of mechanical sci...

A: i). Statics and dynamics - design of Robot in design of robot, you have to design robotic arm by me...

Q: 1 4 2 [2 37 5 -2 2. Multiply. 3 5 7 8 4

A: The matrix is given by AB=142357235-284

Q: Problem 3 A particle moving along a straight line. The velocity as a function of time is as shown. D...

A: From graph the relationship between v and ty=mx v=mt where m is slope and m=tanθ=103v=103t

Q: 2. A square hollow steel strut with a wall thickness, t, = 10 mm is pin connected to two gusset plat...

Q: If the 1,350-lb boom AB, the 178-lb cage BCD, and the 174-lb man have centers of gravity located at ...

Q: The towline exerts a force of P = 4 kN at the end of the 20-m-long crane boom. If x = 24 m , determi...

Q: The volumetric flowrate of CCl4 (? = 0.659 g/cm3) in a pipe is 5.39 L/s. Find:a.the mass flow rate o...

Q: A closed tank 5m high contains 2.5 m of water. A nozzle 75 mm in diameter is installed at the side o...

Q: Q1: If the horizontal component of the force (F) is (24 XN+). De-termiue the magnitude of the force ...

A: we have to determine the components of the force

Q: What are the components of an air service unit?

Q: SIMPLE STRESSES 2. The puncher is to drive a 25 mm diameter hole to a steel plate. If the allowable ...

Q: A mixture of dry air and water vapor is at a temperature of 21 C under a barometric pressure of 101....

A: Since we only answer up to 3 subparts so we will answer only up to 3. Please resubmit the question b...

Q: A foreman is exposed to the hand tool vibration for 30 minutes with the vibration values of ax = 6/s...

A: (i) Write the given data. ax=6 m/s2ay=7 m/s2az=4 m/s2t=30 min

Q: During its final approach to the runway, the aircraft speed is reduced from 326 km/h at A to 210 km/...

A: Given data: u=326 km/h=90.556 m/sv=210 km/h=58.33 m/sm=204 Mg=204×103 kgdx=2 km=2000 mdy=270 m Need ...

Q: Express the number .0000003597 using the powers of ten. ON 359.7 x 106 B) 3.597 x 107 35.97 x 104 D)...

A: GIVEN DATA - A DECIMAL NUMBER GIVEN WE HAVE WRITE IN POWER OF TEN

Q: COMPLETE SOLUTION PLS 4 DECIMAL PLACES

A: Here finallywe should know that pressure gauge gives the reading based on the immediate suroundings ...

Q: Problem 1 Given a steady flow, where the velocity is described by: u = 3 cos(r) +2ry v = 3 sin(y) +2...

A: Given velocity component , u=3 cos(x) + 2xy2 v= 3 sin(y) + 2x2y For a stream function to exist the ...

Q: 3. Given the following data of the figure shown: P= 5.5 KN, L, = L, = L, = 2.5 m Strut BC = 100 mm w...

A: P=5.5kN L1=L2=L3=2.5m

Q: What is the x-component of the resultant

A: To determine the X component of the resultant.

Q: 8 kN/m Refer to figure 19, Calculate the magnitude and 4 kN/m position of the resultant load from po...

A: Draw the free-body diagram of the beam.

Q: Given a 4" x 2" x 20" cylinder. The Relief Valve is set for 2,000 psi. We are using a 10 GPM pump. a...

A: Given: 4x2x20 inch P = 2000 psi To find: maximum force

Q: Given the below information and diagram, determine the angular velocity of link CD in rad/s using th...

Q: A bar ACB has is subjected to an external load at C, and it is supported either end by a cable as sh...

Q: A centrifugal compressor delivers air at 50 kg at a pressure of 2 bar and 97°C. The intake pressure ...

Q: A refrigeration plant produces 0.139 kg/s of ice at -5°C from water at 30°C. If the power required t...

A: given; →mass(m)=0.139kg/s→temperature(T1)=-50c→temperature(T2)=300c→power required(P)=22KW→Cp=2.1KJ/...

Q: Water flows into the sink shown in the figure below at a rate of 2 . If the drain is closed, min the...

A: As per given question Q=2gal/min D2=0.4 in We have to determine require hole for ensure that the wa...

Q: The students reviewed the safety features of a bumper car and evaluated the features based on the mo...

A: 2. answers Safety Features Function Bumper around entire car Reduces amount of force transmitt...

Q: 2 m-1)° = y + 0.6 m = 1 m 10 S

A: Calculated velocity gradients and shear stress.

Q: 4. Estimate the rate at which heat can be conducted from the interior of the body to the surface. As...

Q: FACE TO FACE DIST 44.40 meters Somm gomm gomm USE: 3metes As shown in Figure, a drainage is to be in...

A: Write the face to face distance where pipes are going to be fitted. L=44.40 m Write the length of ...

Q: Situation 9 - A 6-m long ladder weighing 600 N is shown in the Figure. It is required to determine t...

Q: 03-Draw the shear force and bending moment diagrams for the beam shown in Figure (3).

A: Given = The following figure of beam We need to draw shear force and bending momen...

Q: An electrical worker stands in the bucket that hangs from a pin at end D of the boom of the cherry p...

Q: Problem 2.35 The 5-ft concrete post is reinforced with six steel bars, each with a 7/8-in. diameter....

Q: Determine the resultant moment produced by forces FB and FC about point O in N-m. What is the j comp...

Q: Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the ...

Q: Can someone show me how to do the roller, pin, and built-in supports( 2 each) and point them.

Q: –1 0 5] -5 27 1 3 1. 4 -5 0

A: Explanation: ◆ The matrix consists of 2 rows and 3 columns. Hence, it's a 2×3 matrix. ◆ The addition...

Q: A screw eye is subjected to a force of 6 kN and 2 kN as shown in Figure 2.1. Calculate the magnitude...

Q: Analyze the pneumatic problem and design direct and indirect pneumatic circuit diagram with explanat...

A: Direct Activation Pneumatic Circuit:

Q: Determine pressure due to water at depth of 20 m on a body

Q: A polypropylene has the following tensile creep compliance measured at 40 °C: D(t) = 1.2 x tº.1 GPa-...

A: The strain associated to the propylene can be calculated using the formula given below as- ε=D×σavg ...

Q: The pipe assembly is subjected to the force F=58N. Determine the moment of this force about point B ...

Q: During its final approach to the runway, the aircraft speed is reduced from 326 km/h at A to 210 km/...

A: Given data: v=210 km/h=58.33 m/su=326 km/h=90.556 m/sdx=2 km=2000 mdy=270 m Need to determine the ae...

Q: Find the initial velocity of a car which is stopped in 10 seconds by applying brakes. The retardatio...

A: Given data : Retardation=a Final velocity=V Time=t To find : Initial velocity

Q: Use the method of sections to determine the forces in members BD, CD, and CE. Note: The support reac...

A: Given data Given truss system

Q: A box that contains of a 250 kg fragile instrument is transported by a truck that is subjected to a ...

Q: A section through a single cylinder of an internal combustion engine is illustrated in the figure be...

Concept explainers

Properties of Pure Substances

A substance with fixed chemical composition throughout is called a pure substance like water, air, and nitrogen. A pure substance does not have to be a single element or compound. A mixture of two or more phases of a pure substance is also a pure substance as long as the chemical composition is the same for all phases. These substances mainly have a constant/ uniform composition. The substances also have fixed boiling and melting points. A pure substance takes part in a chemical reaction to form predictable products.

Question

100%

Please answer it in 1hr.

Thermodynamics

Science that deals with the amount of energy transferred from one equilibrium state to another equilibrium state.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A fluid flows at 450 ft/s with specific volume of 12.8 ft3 /lbm, pressure of 14.7 psia and specific enthalpy of 430 Btu/lbm. Determine (a) the specific internal energy and (b) the total energy if potential energy is neglected. Ans: 395.2 Btu/lbm; 434.04 Btu/lbm
The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle is operating steadily and heat loss is assumed negligible. If the specific enthalpy of fluid and velocity of the fluid at the inlet are 3000kJ/kg and 220km/hr respectively. At the exit, the specific enthalpy of fluids is 2,7×10^6 J/kg. Determine (a) the velocity of the fluid at the exit of the nozzle in (m/s), (b) Determine the rate of flow of fluid (mass flow rate) when the inlet area is 0,2m^2 and the specific volume at the inlet is 0,3m^3/kg, (c)Determine exit area of the nozzle when the specific volume at the nozzle exit is 0,6 m^3/kg.
A fluid system undergoes a non-flow frictionless process from 4.5 ft 3 to a final volume 1.5 ft 3 in accordance with the defining relation P= 60/V + 30 psi, where volume in ft 3 . During the process the system reject 30 BTU of heat. Determine the change in enthalpy and internal energy.
Steam expands steadily at a constant temperature. The flow rate is 13.6 kg/min with an inlet state of wet steam (water) at 80% quality to a final state of 70°C and 2.5 MPa. The change of kinetic energy across the device is 3.5 kJ/kg, and the heat added is 21.81 kW. Determine (a) the enthalpy of conditions 1&2, (b) the heat transfer in kJ/kg. (c) the work, and (d) the system power.
Through a refinery, fuel ethanol is flowing in a pipe at a velocity of 1 m/s and a pressure of 101300 Pa. The refinery needs the ethanol to be at a pressure of 2 atm (202600 Pa) on a lower level. How far must the pipe drop in height in order to achieve this pressure? Assume the velocity does not change. (Hint: Use the Bernoulli equation. The density of ethanol is 789 kg/m3 and gravity g is 9.8 m/s2.
Methane, with a density of 0.52 kg/m3, enters a burner with a velocity of 30 m/s through a cross-sectional area of 8.2 cm2. Air, with a density of 1.20 kg/m3, enters at a mass flow rate 21 times that of the methane. Exhaust gas, with a flow density of 0.68 kg/m3; leaves through a cross-sectional area of 196 cm2. If the flow is steady, determine the exhaust velocity.(Answer must be 21.1 m/s)
Under steady-flow conditions, the fluid properties at an inlet or exit remain constant (do not change with time)
Between two sections in a vessel, a fluid moves in a steady flow manner. At entrance: A1=20 cm2, ρ1=1878 kgm/m3. At exit: A2=10 cm2, ʋ2=249.5 cm3/g, ῡ2=3048 cm/min. Determine the following: ḿ1 in g/min ῡ1 in m/min
The velocity of a liquid flowing in a circular pipe of radius R varies from zero at the wall to a maximum at the pipe center. The velocity distribution in the pipe can be represented as V(r), where r is the radial distance from the pipe center. Based on the definition of mass flow rate m ., obtain a relation for the average velocity in terms of V(r), R, and r.
A fluid flowing in a pipe 1000 ft above the reference line at a pressure of 200 psia, specific volume of 2 ft3 /lb, velocity of 200 ft/sec and internal energy of 100 Btu/lbm. Determine (a) the total energy of the flowing fluid with respect to the reference line and (b) the specific enthalpy in Btu/lbm . Local gravity is 32 ft/sec2 .
The fluid condition at the inlet and exit of a horizontal convergent nozzle is analysed. The nozzle is operating steadily and heat loss is assumed negligible. If the specific enthalpy of fluid and velocity of fluid at the inlet are 3000kJ/kg and 220km/hr respectively. At the exit, the specific enthalpy of fluid is 2,7×10^6J/kg.Calculate (a) the velocity of the fluid at the exit of the nozzle in (m/s), (b)Determine the rate of flow of fluid (mass flow rate) when the inlet area is 0,2 m^2 and the specific volume at the inlet is 0,3m^3/kg, (c) Determine exit area of the nozzle when the specific volume at the nozzle exit is 0,6m^3/kg
Helium is used in the Carnot engine where the volumes beginning with constant temperature heat addition are V1= 0.3565 m3; V2= 0.5130 m3; V3= 8.0 m3; V4= 5.57 m3. Determine the thermal efficiency. Use 1.66 as the specific ratio of helium.