The net ultimate bearing capacity of a purely cohesive soil A. Depends on the width of the footing and is independent of the depth of the footing B. Depends on the width as well as the depth of the footing C. Depends on the depth, but is independent of the width, of the footing D. Is independent of both the width and the depth of the footing

The net ultimate bearing capacity of a purely cohesive soil A. Depends on the width of the footing and is independent of the depth of the footing B. Depends on the width as well as the depth of the footing C. Depends on the depth, but is independent of the width, of the footing D. Is independent of both the width and the depth of the footing

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter11: Load And Resistance Factor Design (lrfd)

Section: Chapter Questions

Problem 11.1P: A continuous foundation is required in a soil where c=10kN/m2, =26, and =19.0kN/m3. The depth of the...

See similar textbooks

Similar questions

B Jf g is the punching shear resistance per unit area a, is the side of a square footing for a column of side b, carrying a weight W including the weight of the footing, the depth (D) of the footing from punching shear consideration is
5-A 10ft continuous flexible strip footing is subjected to a load of 500 psf. Find the change in stress A - Below a point 3ft deep and 6ft perpendicular to the center of footing. B - Below the edge of the foundation at a depth of 3ft. C - Below the center of the footing at a depth of 3ft.
Design a square pad footing with an overall depth of 600mm, cover to the reinforcements 50mm with 20mm diameter reinforcement bars in both directions. The footing carries a 400mm square column with a dead load of 1050KN and imposed load of 300KN. The safe bearing capacity of the soil is 170KN/m^2, fcu 30N/mm^2. Assume a unit weight of concrete to be 24KN/m^3 and footing weight 150KN
PROBLEM #1: The figure below shows a strip footing. Determine the footing width and design the bottom transverse reinforcing. Confirm the section is tension controlled. T D As W P₁ = 3.5 k/ft P₁ = 5.5 k/ft qallow = 2.3 ksf f' = 4 ksi = 0.9 (verify)
the pad footing is used to support the load of 12 000lb. determine the intensities (in lb/ft) w1 and w2 of the distributed loading acting on the base of the footing for the equilibriumWhat is the computed value of w1 in pounds per foot What is the computed value of w2 in pounds per foot
A strap footing consists of two footings connected by strap beam. Allowable soil pressure is 450 kPa. Footing thickness is 600mm and the bottom of the footing is 1.5m below the ground. Assume soil weight to be 19 Kn/m3 and concrete weight to be 24 Kn/m³. Use f'c = 20.7 Mpa and fy = 414 Mpa. Use 1.2DL + 1.6LL. gog = galow - footing weight – soil weight. DL = 275 kN LL = 400 kN DL = 600 kN LL = 500 kN 4.8 m 400 x 400 column 400 x 400 column 1.2 m 1.2 m a) Calculate the footing dimensions. (Size is in multiples of 100 mm) b) Draw the Shear and Moment Diagram on the Longitudinal Direction. Show the maximum shear and moment.
Forces in the column bars are transferred to the footing through No 10 bars. Determine the development length required into the column and into the footing if the steel has a yield stress of 60 ksi. Normal weight concrete is used. The concrete strength in the column is 6,000 psi and the concrete strength in the footing is 5,000 psi up into column down into footing
A square footing with 1.5m x 1.5m in dimentions, if the the friction angle of the supporting soil is 25, and its unit weight is 17.5 kN/m3; the value of the third term of ultimate bearing capacity (according to general shear failure equations) is: a. 117 kN O b. 88 kN/m2 O c. 117 kN/m2 d. 88 kN
QUESTION 3 A footing of size 2.5 m x 2.5 m and 450 mm thick resists characteristics axial loads of 500KN dead and 200 kN imposed from a 300mm square column. The safe bearing pressure on the soil is 230kN/m?. a. Check whether the base pressure is safe b. Design the bending reinforcement, assuming 16mm diameter bars c. Check the punching shear Further Design Information Characteristic strength of concrete (fm) = 35 N/mm? %3D Characteristic yield stress of steel (f;) 460 N/mm2 Cover to reinforcement = 75 mm Diameter of main bars = 16 mm Unit weight of concrete = 24 kN/m³
Bearing Capacity A strip footing is resting on the ground surface of a pure clay bed having an undrained cohesion cụ. The ultimate bearing capacity of the footing is equal to
QUESTION 2 If e = B/6, the resultant force of the bearing pressure distribution acts at O a corner of the footing Ob third-point of the foundation Oc away from the footing Od center of the footing
A square footing 2.5m x 2.5 m supports a square column 300mm x 300mm at its center. Concrete cover to bar centroid = 100mm. Ultimate load combination is 1.2DL + 1.6L. Column loads aee service conditions: DL= 680 KN LL = 400KN f'c = 20.7 Mpa fy = 275 MPa Calculate the nominal punching-shear stress acting at the critical section of the footing slab if the thickness of the slab is 450 mm.