The network shown in Figure 1.179(a) consists of a collection of resistors, a battery, and a current source. Use suitable operations to reduce this network to the equivalent shown in Figure 1.179(b). Calculate values for EAB and RAB in the equivalent. R, R3 A 3KO 2ΚΩ Jg2 Eg1 - E 8V R2 12KΩ R 3KO 1.2mA R4 R5 1KO 1KO (a) RAB A EAB B (b) Figure 1.179 (a) Resistive network (b) Equivalent network at A-B B.

The network shown in Figure 1.179(a) consists of a collection of resistors, a battery, and a current source. Use suitable operations to reduce this network to the equivalent shown in Figure 1.179(b). Calculate values for EAB and RAB in the equivalent. R, R3 A 3KO 2ΚΩ Jg2 Eg1 - E 8V R2 12KΩ R 3KO 1.2mA R4 R5 1KO 1KO (a) RAB A EAB B (b) Figure 1.179 (a) Resistive network (b) Equivalent network at A-B B.

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter27: Service-entrance Equipment

Section: Chapter Questions

Problem 44R

See similar textbooks

Similar questions

A copper transmission line is to be replaced by one of aluminum having the same total resistance. If the cross sectional area of the copper wire is 0.005m2 , what would be the cross sectional area of the new aluminum wire? *Draw the diagram
Since R1=5619.38ohm, R2=1949.32ohm and Ri=Infinite in the circuit given in the figure, write the equivalent resistance in Ohms between the terminals A-B. When making your transactions, 2 digits will be taken after the dot.
A copper transmission line is to be replaced by one of aluminum having the same total resistance. If the cross sectional area of the copper wire is 0.005m2 , what would be the cross sectional area of the new aluminum wire? Note: DRAW THE DIAGRAM
Please Answer question 3some provided answers:b. Tstart = 71.93 Nm c. Istart = 179.51 A ..
A copper conductor wire with a total length of 100ft is used in a 15 amp common household circuit has a resistance of 1.62 ohms/1000ft. If the circuit is fully loaded, determine the heat produced by the conductor? (Hint 1W = 3.413Btu/hr) a. 124.40 Btu/hr b. 99.83 Btu/hr c. 8.29 Btu/hr d. 177.50 Btu/hr
Subject EE466 power system protection Please answer the question A part 1 and 2 X= 4 and Y =3
PLEASE PROVIDE COMPLETE SOLUTION CLEARLY. If R1= 56 Ohms, R2= 36 Ohms, R3= 46 Ohms, and IR1= 2 A, Calculate for Et in Volts.
For the circuit shown, determine the equivalent voltage source in Volts where I1=10 A, I2=1 A, R1=16 Ω, and R2=33 Ω. (i.e. What voltage source should be in series with the a resister to create an equivalent circuit?)
Since R1=3198.15ohm, R2=9694.26ohm and Ri=Infinite in the circuit given in the figure, write the equivalent resistance in Ohms between the terminals A-B. When making your transactions, 2 digits will be taken after the dot. Write the result you found according to the margin of error of ± 10% (plus/minus ten percent). While writing the answer, a space is written in front of the value (kOhm, ohm, V, A) etc. values should not be written. Only numeric values should be entered. A period (.) must be used as a decimal separator. Do not use thousands separators (do not use signs such as semicolons). An example notation is given below. Let the value you find be 1.15Kohm. You should write 1150.00 in the box. Let the value you find be 432.63 ohms. You should write 432.63 in the box. If the correct answer is X, values entered in the range of X ± (X*10/100) (including limits) will be accepted. If x=50, it will be accepted as between [45,55].
B. Copper wire of length (/) connected in parallel with aluminum wire of length (21) and (10mm) diameter, if the current in each wire is the same. Find the diameter of the copper wire if the resistivity of copper is (0.0159 u2-m)& for aluminum is (0.0254 ul-m).
Look at the images shown. Why can we measure resistance with a pencil drawn on a piece of paper? What is the component/material that is on the pencil that gives a high resistance? With the values given on the images, what are the corresponding color codes (indicate tolerance using a 4-band color code scheme)? If the first value is connected in series with the other value, what is the total resistance? If it’s parallel what is the total resistance? 0.449 mega ohms 102.2 kilo ohms
(a) In Figure 2.1, determine (i) the current I1,(ii) the voltages V2 and Vab,(iii) the value of resistor R4.