The output voltage of a single-phase full-bridgeinverter is controlled by pulse-width modulation with onepulse per half-cycle. Determine the required pulse width sothat the fundamental rms component is 70% of dc inputvoltage.

To determine the required pulse width for the fundamental RMS component to be 70% of the DC input…

Answered: The output voltage of a single-phase…

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Draw a symbol for a solid-state logic element AND.
A single phase half-bridge voltage source inverter (VSI) has a resistive load of 2.4Ω andinput dc voltage Vdc = 48V. The desired fundamental frequency of the load voltage is 50 Hz.Determine: RMS output voltage at fundamental frequency and voltage rating of switches
Using the sine PWM method with the full bridge inverter below, it is desired to generate a voltage of 50Hz on the series RL load. A voltage of 120 V DC is applied to the input of the inverter circuit. Amplitude modulation rate ma = 0.9 and frequency modulation rate mj = 19. The resistance of the series RL load is 15 ohms and the coil inductance is 40 mH. What is the total harmonic distortion value (THD) of the power drawn by the load resistor and the load current?
Find the RMS voltage expression of output phase voltage of a balanced three-phase square wave inverter need it asap
Using the sine PWM method with the full bridge inverter below, it is desired to generate a voltage of 50 Hz on the serial RL load. A voltage of 120 V DC is applied to the input of the inverter circuit. Amplitude modulation rate ma -0.9 and frequency modulation rate mf -19. The resistance of the series RL load is 15 OHM and the coil inductance is 40 mH. a) What is the power drawn by the load resistor?b) What is the total harmonic distortion value (THD) of the load current?
What is the maximum conversion time for a 16-bit dual-ramp converter using a 1-MHz clock frequency? What is the maximum conversion rate?
The output signal from a frequency inverter will appear on a scope screen as a: A. pure sine wave of different frequencies. B. triangular-shaped waveform with distorted peaks. C. distorted square wave. D. distorted sine wave.
A single-phase full bridge inverter is operated from a 48V battery and issupplying power to a resistive load of 10 Ω. Determine:(i) The fundamental output voltage and first five harmonics.(ii) RMS value by direct integration method and harmonic summationmethod.(iii) Output rms power and output fundamental power.
HWI: The Single - phase full bridge inverter has a resistive load of R = 10Omega and the ec input Voltage is 220v. Determine: a. The rms output voltage and current b. The rms output voltage at the fand amential frequeng c. The output power. er.
A single phase half bridge inverter has input voltage of 48 V DC. Inverter is feeding a load of 2.4 ohm. The rms output voltage at fundamental frequency is ?
Q/ for square wave PWM inverter, Vdc=100V, L=25mH, R=10Ω, f=60Hz. draw the spectrum of the output voltage and current and then find the rms current value and the output power. Take n =1-20.
We need to generate a PWM signal with frequency of 2 KHz, and duty cycle of 20%. The clock frequency is 1 MHz and the counter is configured in count-up-down mode. Determine the values that we need to write in LOAD and COMPARE registers. You can use either pwmA or pwmB.

SEE MORE QUESTIONS

Recommended textbooks for you

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Electric Motor Control

Electrical Engineering

ISBN:

9781133702818

Author:

Herman

Publisher:

CENGAGE L

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

The output voltage of a single-phase full-bridge inverter is controlled by pulse-width modulation with one pulse per half-cycle. Determine the required pulse width so that the fundamental rms component is 70% of dc input voltage.