The part shown is made from AISI 1040 CD steel and is loaded at point C with 300 N in the positive y direction and at point E with 200 N in the positive x direction. The diameter of the bar ABD is 12 mm. Dimensions in mm. 12 dia E 200 N B 300 N 40. 50° 60 Evaluate the state of stress at points A, B, and C, determine the critical case, and evaluate the minimum factor of safety based on the maximum-shear-stress theory. The factor of safety is [

The part shown is made from AISI 1040 CD steel and is loaded at point C with 300 N in the positive y direction and at point E with 200 N in the positive x direction. The diameter of the bar ABD is 12 mm. Dimensions in mm. 12 dia E 200 N B 300 N 40. 50° 60 Evaluate the state of stress at points A, B, and C, determine the critical case, and evaluate the minimum factor of safety based on the maximum-shear-stress theory. The factor of safety is [

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.2.1P: A rigid bar of length L is supported by a linear elastic rotational spring with rotational stiffness...

See similar textbooks

Similar questions

Three steel rods (E = 200 GPa) supports a 50 kN load P. Each of the rods AB and CD has a 300 mm2 cross-sectional area and rod EF has a 600 mm2 cross-sectional area.State whether the structure is statically determinate or indeterminate. Why?Determine the force and the stress in each rod.Determine the deformation of each rod. Note: The link BED is rigid, and BE = ED.
The aluminum (E=15x10^10psi, α=11.6x10^-6/°F) shell is fully bonded to the brass (E=10.6x10^6psi, α=12.9x10^-6/°F) sore, and the assembly is unstressed at a temperature of 78°F. Considering only axial deformations, determine the stress when the temperature reaches 180°F (a) in the brass core (b) in the aluminum shell
A 75 mm diameter compound bar is constructed by shrinking a circular brass bush onto the outside of a 50 mm diameter solid steel rod. If the compound bar is then subjected to an axial compressive load of 160 kN determine the load carried by the steel rod and the brass bush and the compressive stress set up in each material. For steel, E = 210 GN/m2; for brass, £ = 100 GN/m2
The steel rod in Fig. is to be used to support an axial load of 18 kip. If Est = 29(103 ) ksi and sY = 50 ksi, determine the smallest diameter of the rod as allowed by the AISC specifications. The rod is fixed at both ends.
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve in (Figure 1). The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (σY)st=680MPa, and for the bronze (σY)br=490MPa, determine the magnitude of the largest elastic load P that can be applied to the assembly. Est=200GPa, Ebr=100GPa. Express your answer to three significant figures and include appropriate units.
Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 2.0-in. wide, 1.00-in. thick, and made of aluminum that has anelastic modulus of E = 12,000 ksi. Determine the maximum magnitude of load P that can be applied to the rigid bar withoutcausing member (1) to buckle
The stepped bar with a circular hole is made of annealed 18-8 stainless steel. The bar is 12 mm thick and a change in depth from D = 130 mm to d = 100 mm. It will be subjected to an axial tensile load of P = 70 kN. The normal stress in the bar is not to exceed 150 MPa. Determine: a) the maximum allowable hole diameter b) the minimum allowable fillet radius
When a hydraulic cylinder is firmly anchored and pushing on a guided load, the effective length of this column is the stroke of the piston rod. (a) Calculate the critical stress of the rod if the rod has a diameter of 3.8 cm and a stroke length of 2 m? The rod is made of 304 stainless steel. Answer: 42.31 MPa (b) Calculate the maximum load (in kg) that can be lifted while respecting a safety factor of 2. Answer: 2448 kg
For the assembly shown, determine the displacement of points B and D as the load of 50KN is applied at D. Rod BC is steel with length = 2m, A = 600mm2 E =200GPa.Bar ABD is rigid. What is the stress in the rod CB? What is the shear stress of the bolt of the pin at A if its diameter is 20mm? Please provide complete FBD.
Please answer and provide a clear solution. thankyou. The five-bolt connection must support an applied load of P = 2600 lb. If the average shear stress in the bolts must be limited to 25 ksi, determine the minimum bolt diameter that may be used for this connection.
The horizontal link BC is 1/4 in. Of thickness and width w = 1.25 in., It is made of steel with an ultimate tensile strength of 65 ksi. What is the factor of safety if the structure shown was designed to support a load P 10 kips?
A reinforced concrete collumn 200mm in diameter is designed to carry an axial compressive load of 320kN. Determine the required cross sectional area of the reinforcing steel if the allowable stress are 6MPa for concrete and 120MPa foe steel. Use Eco=14GPa and Est=200GPa. -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.