Answered: The phase b voltage and the phase b…

The phase b voltage and the phase b current of a balance three-phase system are V = 220 sin (wt + 210°) and I = 10 sin (wt-180°). *

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.23P: A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the...

See similar textbooks

Related questions

Q: 2. A Y-connected balanced 3-phase source is supplying a balanced 3-phase load. The source phase A…

A: For Star connected system, Phase voltage = line voltage/sqrt(3). Line current = phase current. For…

Q: The following three-phase circuit is symmetrical, with line voltage 220 V, 60 Hz, direct phase…

A: Given data: VL-L=220V, Frequency,f=60Hz Zan = 10 ohms, Zbn = -10j ohm, Zcn = -10j Ohm

Q: Question No. 1: Figure below gives the general D-Y transformation, (a) Show that the general…

A: The general transformation reduces to as given in figure for a balanced three phase loadFor ∆-…

Q: Given: 1. 2 wye-connected loads per phase to a 3 phase power source 2. first load consists of a…

Q: For the circuit in the figure, Determine the complex power delivered to the three-phase load. The…

Q: 12. In an unbalanced system, the phase voltages are: Vna = 13220 Vnb = 1302235 Vnc = 1332117 What is…

A: 12. Given parameters are: Vna=132∠0°V,Vnb=130∠235°V,Vna=133∠117°V, The line to line voltage is:…

Q: Q4) The three phase circuit seen in the following figure is derived by a three phase balanced…

A: the sinusoidal steady-state solution of the iR (t) current , and . the total complex power consumed…

Q: For an AC power distribution circuit, the line voltage is 480V and the line current is 53A. The…

Q: 3. Suppose a voltage v(t) = v2 × 120 sin(377t + 30°) is applied to a single phase oad, and the…

Q: Question 3 An unbalanced, three -phase, three-wire, star-connected load is supplied from a balanced…

A: Given Za =28∠37°ΏZb =15∠-78°ΏZc =20∠83° ΏVl =380 V

Q: DIagram: FauLt h phase 3phase Load Source 2 Line Values: sourte Line Impedances: • Eon: 120 L0' v •)…

A: Under unbalanced condition with fault We have to find load power profile Active (PT), reactive (QT),…

Q: Figure 4: Pgen, Pgen, Pload. 200 MW Pload, 550 MW Line Line Reactance (Per Unit) x12-0.1 1-2 1-3 2-3…

A: Power delivered by the line having sending end voltage V1 and receiving end voltage V1 with del is…

Q: Impedances Z2 and Z3 in parallel are in series with impedance Z1 across a 100 V, 50 Hz ac supply. Z1…

Q: Vab = 200 cos (t - 10°), Vbc = 200 cos (t - 230°), Vca = 200 cos (t - 110°)" A POSITIVE PHASE…

A: In this question, We need to choose the correct options What is phase sequence of the given system?…

Q: Assume that the phase-voltage magnitudes for a wye system are 100V. Find the magnitude of the…

Q: Problem: The sequence components of phase A currents are: la0 = 0.47 + j1.49 A la1 = 18.4 cis -…

A: Given sequence components of phase A currents : Ia0=0.47+j1.49 A=1.562∠72.5° A Ia1=18.4∠-31.6°…

Q: A single-phase load is supplied by a single-phase voltage source. If the current flowing from the…

Q: balanced three-phase Delta connected voltage source supplies Delta connected three-phase symmetrical…

A: In the question the source is balanced and connected to balanced load through transmission line. For…

Q: 2. In an unbalanced system, the phase voltages are: Vna = 13240 What is the line to line voltage…

A: In this question, Unbalanced voltages are given. Find the line voltage VCB ? VCB = Vnb -Vnc

Q: lanced three-phase source with grounded neutral has line-to-line voltages of 208 volts with ab-bc-ca…

A: In this question, A balanced three-phase source with grounded neutral line-to-line voltagesVLL =…

Q: Source: Zan = Zon = Zon = 0.1 + j1.5 N En = 12020° v En = 1202 - 120° v Een = 1202120° v -bn Line:…

A: Without FAULT

Q: A three phase star connected voltage source has line voltage of 415V and the frequency 50 Hz. This…

A: Star system: If we connect the three terminals of three winding together. Condition is that connect…

Q: Q2 Two single-phase voltage sources, V1 and V2 are connected by parallel line impedance of Z11 = 1+…

A: In this question we will find current supplied and recieved by voltage sources and real and…

Q: Convert the wye-connected load to its delta equivalent. What is the per phase impedance of the delta…

A: Given

Q: A three-phase source has a phase sequence of EAS- Esc - ECA and delivers the following delta load…

Q: Determine the phase sequence of the set of voltages Van = 200 cos(ωt + 10°), Vbn = 200 cos(ωt −…

A: to determine the phase sequence of the set of voltages Van = 200 Cos (ɷt+10˚) V bn = 200 Cos…

Q: 3.15. The three-phase power and line-line ratings of the electric power system shown in Figure 30…

A: Sol:-(a) The base voltage VBG1 on the LV side of T1 is 20 kvHence, the base on its HV side…

Q: 7.61 For the three-phase circult shown in Figure P7.61, find the current in the neutral wire and the…

A: The three-phase circuit diagram is:

Q: Three Impedances each of (6 – j26)Ω are connected in mesh across a three-phase 425V ac supply.…

Q: A balanced three-phase source with grounded neutral has line-to-line voltages of 208 volts with…

A: In this question, A balanced three-phase source with grounded neutral line-to-line voltages =208…

Q: If a balanced 3-phase system has its phase voltage Van = 120440°, then the line-to-line voltage Vpc…

Q: la A Z2 VAB VCA IAB ICA B Z3 TBC le VBC

A: In the Star Connection, the 3 winding's similar endpoints are connected to a common point known as…

Q: Consider the balanced three-phase circuit is given below. The voltage values indicated are rms…

Q: Figure Q1(b) shows a three-phase electrical circuit connected in Y-A configuration. The line voltage…

A: For sketching the per phase circuit, we will convert the delta connected load to star connection for…

Q: A three-phase substation bus supplies a wye and a delta connected constant impedance loads. The…

A: NOTE- As per the rules we can answer only 3 sub-parts, please post the remaining sub-parts as the…

Q: Q2. (a) Figure Q2 shows an unbalanced three-phase circuit. Determine the line currents and complex…

Q: Three impedances Z1, Z2 and Z3 are delta-connected to a symmetrical 3-phase, 400 V supply of phase…

Q: Three Impedances each of (13 -j16) ohm are connected in mesh across a three-phase 405V ac supply.…

A: Given, Per phase impedance Zph = 13 - j16 ohm Three phase supply voltage VL = 405 volts Mesh…

Q: The phase voltages across a certain load are given as: Va = 176 – j132 volts Vb = -128 - j96 volts…

Q: j2 Ω m -jXcQ HE RQ ww 40/0° V ZL 5Ω or the circuit shown above, what is the magnitude of the load…

Q: pute the phasors I,, I, and V. (b) Draw a phasor diagram showing I, I,, I, and V.

A: Given thatI=10∠00A

Q: Consider the following three Phase balanced Circuit 210 20⁰ Vrms jasn 210/120⁰ Vrms 24-321 jost mm…

A: The three-phase delta connected load is shown below: The per-phase equivalent load impedance will…

Q: 1. In a balanced 3 phase wye connected system. the line voltage and the corresponding phase voltage…

A: Since we only answer up to three sub-parts, we’ll answer the first three. Please resubmit the…

Q: atelier -j0,3 N 0,2 0 13 11 12 Is + j6 N j8 N Es 10Ω -j 12 N ·

A: Given information: The source voltage is Es=250.7<-4.16° Volts. Here atelier is the workshop. We…

Q: power

A: In this question, we have to answer about reactive power..

Q: What would be the phase-to-neutral voltage from a 3-phase, wye-connected system if the line-to-line…

Q: A three-phase load consists of three 100-Q resistors that can be wye- or delta-connected. Determine…

Q: Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results: 0.C.…

Question

The phase b voltage and the phase b current of a balance three-phase system are V = 220 sin (wt + 210°) and I = 10 sin (wt-180°). *

A. 5256.44 W

B. 5514.38 W

C. 5715.76 W

D. 6049.22 W

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current i(t)=5cos(t+50)A. (a) Determine the power triangle. (b) Find the power factor and specify whether it is lagging or leading. (c) Calculate the reactive power supplied by capacitors in parallel with the load that correct the power factor to 0.9 lagging.
Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.
A single-phase source has a terminal voltage V=1200volts and a currentI=1530, which leaves the positive terminal of the source. Determine the real and reactive power and state whether the source is delivering or absorbing each.
The phase voltages across a certain load are given as: Va = 176 – j132 volts Vb = -128 - j96 volts Vc = -160 + j100 volts Va1 = 163.24-j35.10 / 166.97L-12.135 Va2 = 50.1-j53.9 / 73.59L-47.09 Va0 = -37.34-j42.67 / 56.70L-131.19 Compute for positive, negative, and zero sequence components of voltage.
Calculate ZL for maximum average power transfer in the circuit, and find the maximum average power delivered to the load. The given answer is ZL=2-j2 Ω, PL=45 W
For the circuit in the figure calculate: Line and phase currents Line voltages at the load The neutral current Draw the phasor diagram for currents and voltages
ZL impedance for maximum average power transfer in the circuit shown in Figure 2and find the value of the maximum average power transferred to the ZL? (Can you write the steps in detail in sentences?)
Circuit elements with an inductance of 200 mH, a capacity of 50 μF and a resistance of 10 Ω connected in parallel. if we apply average value of 198 V sinusoidal AC voltage to the system . Find the line current, impedance and phase angle of the circuit. (Take Frequency in 60 Hz)
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the apparent power supplied by the generator. The apparent power supplied by the generator is _____ VA.
For the following network find a) Isb) PT, QT, ST and PFTc) Draw power triangle d) Raise the power factor to unitye) Compute Is after raising the power factor
Solve all parts or will dislike For the following circuit, the source voltage phasor is: ?s = 250.7∠ -4.16 deg ? a) Calculate the equivalent workshop impedanceb) Deduce the value of the phasor ?c) Calculate the voltage at the workshop terminals using the ohm lawd) Calculate the voltage at the workshop terminals using the law of loopse) Determine the real and reactive powers of the workshop and its power factor solve all parts or will dislike