The photo coordinates at the bottom of a light pole are (80.54, 40.12) mm. The photo coordinates at the top of the light pole are (83.22, 41.05) mm. The photo was taken with a 6” focal length camera flying 2200 feet above the ground. What is the pole height?

The photo coordinates at the bottom of a light pole are (80.54, 40.12) mm. The photo coordinates at the top of the light pole are (83.22, 41.05) mm. The photo was taken with a 6” focal length camera flying 2200 feet above the ground. What is the pole height?

Traffic and Highway Engineering

5th Edition

ISBN:9781305156241

Author:Garber, Nicholas J.

Publisher:Garber, Nicholas J.

Chapter14: Highway Surveys And Location

Section: Chapter Questions

Problem 10P

See similar textbooks

Related questions

Q: 5/103 Find the reaction at A due to the uniform loading and the applied couple. 2 kN/m 12 kN-m A 3 m...

A: Here vertical component of reaction at the point A is Ay, horizontal component of reaction at point ...

Q: Prob. 2.3-7. For small loads, P, the rotation of "rigid" beam AF in Fig. P2.3-7 is controlled by the...

A: The change in length of a stressed structural member divided by the initial length of the unstressed...

Q: A car bumper is designed to bring a 1800 kg car to a stop from a speed of 2.23 m/s while deforming 1...

A: Given: The mass of the car is 1800 kg. The initial speed is 2.23 m/sec. The distance is 150 mm.

Q: The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and ...

Q: A levee is being designed to withstand the 100-year storm. Within how many years of construction wil...

A: We will solve this question in step no. 2

Q: Assume straight line instead of parabola for stress strain curve of concrete as follows and partial ...

Q: The uniform A-36 steel bar in Fig. 4-5a has a diameter of 50 mm and is subjected to the loading show...

Q: 52. Which type of inspection is more intensive involving examination of structural elements? A. O Mi...

Q: Determine the load that can be applied at the end of the rigid bar if the stress either spring shown...

A: Step 1: Spring stiffness: Stiffness of first spring= 83 x 103 x 10^4/(8x150^3x20) =1.537 N/mm Stiffn...

Q: 5. In case of bridge greater than 10.7m in height and which canno be inspected from beneath due t wa...

A: To find: Which is best for inspection

Q: 4. An igloo or Eskimo hut is built in the form of a hemispherical shell with an inside diameter of 1...

A: Given Data- Hemispherical shell igloo/eskimoInside diameter=12 ftuniform thickness=2 ftweight=40 lb ...

Q: Evaluate the resisting capacity against axial load due skin friction of a concrete pile embedded int...

A: To determine the resisting capacity of a concrete pile due to skin friction against axial loading. ...

Q: Use A992 steel and select a structural tee for the top chord (highlighted in red) of the welded roof...

Q: A machine having a first cost of Po0,000 s computed using constant percentage of the declining book ...

Q: The kinetic energy E of a body is proportional to its weight W and the square of its velocity v. A 1...

Q: A submersible pump is pumping water from a well that is 200 ft of water through a 4 inch PVC pipe. T...

A: Given - Dia of pictures pipe = 4in. Head of well = 200ft Horizontal pipe length = 2000ft Pressure d...

Q: Question 1: A. Using Neat Sketchs, Ilustrate the main segemesnts of GPS System B. What are the main ...

Q: Problem 1. A column 225mm x 225mm in section carries an axial load of 350 kN. E = 12,036 MPa, fp = 9...

A: Load carrying capacity of column according to euler's formula π*π*E*I / L * L E is given Length is...

Q: 60° v-notch weir impact the discharge coefficient? -How does the notch angle (60°) effect the device...

A: Given data, Angle of v- notch weir = 60°

Q: Prove that AB=A(By)=B(Ay) Let A=xD+2 and B=xD-1

A: Solution: A = x D+2; B= x D-1 Multiplying A and B AB = ( x D + 2) (x D - 1)=x2 D2 + x D - 2 -...

Q: y Wo L L 2 2 FIG. P6.23

Q: A floor is supported by 75mm x 200mm wooden joists spaced @ 400 mm on centers with an effective span...

Q: - One of the testing equipments used for inspection is?

A: To find: Which is testing equipment used for inspection.

Q: 1. When is separation of variables applicable? 2. How can homogeneous equations be distinguished? ...

A: Note- Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-part...

Q: A section of highway has a speed-flow relationship of the form q = au2 + bu It is known that at capa...

Q: [A] prove that the Property 1 and 2 of determinant [C] and 'k' prove that Property 3 of determinant ...

Q: Chapter 2, Problem 2/088 An exhaust system for a pickup truck is shown in the figure. The weights Wh...

Q: tive shear is -383.8666666 cal reaction of hinge suppc 13333333333KN, determin owns. (DRAW THE SHEAR...

A: Take moment about left support :∑ M=0-P7-12w25+23-w52.5+316.1335=07P+18.66673w=1580.665.......1Maxim...

Q: Question 2: (50 marks) The v-t graph shown. Find the distance traveled for the time 0 to (1500+N) se...

A: Given - N= 26 To find- DISTANCE TRAVELLED FOR THE TIME 0 TO ( 1500 + N) I.e 1500 + 26 = 1526 sec. ...

Q: 1. An executive receives an annual salary of P600,000 and his secretary a salary of P180,000. A cert...

A: Given - Annual salary = P600000 Salary of secretary = P 180000 To find- Cost of performing task by...

Q: With the soil profile as shown below, if the water table gradually drops to elevation (E) = -6 m, th...

Q: PKn to 500 KN.m 1.5m 1.5m 30 10m Fir O1

Q: A compound shaft consisting of a 50mm diameter bronze segment and a 75mm diameter aluminum segment i...

Q: . The pachometer is used to locate the

A: To find: What is use of pachometer

Q: *7-32. The double T-beam is fabricated by welding the three plates together as shown. Determine the ...

A: To find - Shear stress in weld necessary to support shear force of V = 80 KN Solution :

Q: The perpendicular distance between the parallel tangents of a reversed curve is 35 m. The azimuth fr...

A: Reverse Curve: A curve that consists of two simple curves which are joined together and curving in o...

Q: We have a 20 meter long pipe for sewage transfer. If the mass percentage of solids in the effluent i...

A: length -20m Effluent %= 0.5 Minimum slope of the pipe (s)=?

Q: Calculate the stress in a 65-ft steel cable that has a total deformation of 0.33 in.

Q: The yearly precipitation in California has normal distribution. Calculate the value of the 50 year a...

Q: Determine the mass of the heaviest uniform cylinder that can be supported in the position shown with...

A: Stress in cable BC =σBC = 50Mpa Cross sectional area of BC = 100mm2 It has been asked in the quest...

Q: 8.17 The frame of the bow saw is a bent tube of 3/4-in. outer diameter and 1/16-in. wall thickness. ...

Q: A submersible pump is pumping water from a well that is 200 ft of water through a 4 inch PVC pipe. T...

Q: The given data shows a sieve analysis of the soil sample. Classify the soil according to AASHTO Meth...

Q: 1. An executive receives an annual salary of P600,.000 and his secretary a salary of P180,000. A cer...

Q: By the conditions of the will, the sum of 35,000 is left to a 12 year old girl to be held in a trust...

Q: A force is applied at the left end of a block resting on a surface. The internal effect of the force...

Q: A car bumper is designed to bring a 1800 kg car to a stop from a speed of 2.23 m/s while deforming 1...

A: Given:- m=1800kg Car stop from 2.23 m/s to zero, while deformation is 150mm Initial velocity u=2.23 ...

Q: 6.31 For the overhanging beam, compute the value of EIð under the 15-kN load. |15 kN 6 kN/m 3 m 5 m ...

Q: Sketch the shear and moment diagram for the beam loaded shown. 6kN/m 10kN 4kN/m lo5m 1.5h In

Q: The resultant of the three forces shown is a counterclockwise couple of magnitude 150 kip-ft. Calcul...

A: To find out the magnitude of all forces.

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The images of the top and bottom of the utility pole are 129 8 mm and 125 2 mm respectively from the main point of the vertical photo. What is the height of the mast if the flying height above the baseboard is 800m?
If the distance from the instrument to the focus is 0.38m, determine the following:a) Horizontal distance between A and B.b) Difference in elevation between A and B.
In the accompanying sketch, a vertical angle of −14°30' is read to a target 1.75m above point M. The measured inclined distance (S) is 644.15m and the elevation of point K is 320.70m above mean sea level.If the height of instrument at K is 1.27m, the elevation of M, considering the effects of the earth's curvature and atmospheric refraction, is?answer. 158.97m show solution please.
If the distance from the instrument to the focus is 0.38m determine the horizontal distance between a and b
A vertical photograph was taken, with a camera having a 152.9-mm focal length, from a flying height 2160 m above sea level. What is the scale of the photo at an elevation of 385 m above sea level? What is the datum scale?
1. A camera was equipped with a 152mm (6”) focal-length lens is used to take a vertical photograph from a flying height of 2780m above mean sea level. If the terrain is flat and located at an elevation of 500m: a.) What is the scale of the photograph? b.) What would be the scale at mean sea level?
Determine the backsight or foresight distance for an instrument set up which will cause an error due to earth’s curvature and atmosphere’s refraction equal to 0.0015 m, 0.0575 m, 0.0986 m, 0.2935 m, and 0.8750 m.
The vertical photograph was exposed with a 60 cm focal length camera at a flying height of 3,000 meters above datum. What is the photo scale at point a if the elevation of point A on the ground is 300 m above datum?
Calculate the centroid (y and x bar) of the shaded area
explain how to set the observing rotation of a polarimeter to zero before starting to measure rotation of the standard solution
Write down about the modification of the basic Dutch cone penetrometer?
Determine the area and the location of the centroid (x,y) of the shaded area.