The pipe ABCDE is supported by ball-and-socket joints at A and D and by cable ECF that passes through a ring with negligible friction at C and is attached to hooks at E and F. Knowing that the frame supports a uniformly distributed load of 2300 N/m along segment CD, answer the following questions. 245 mm 240 mm E 90 mm B 2300 N/m 80 mm 120 mm. X Y Ring C

The pipe ABCDE is supported by ball-and-socket joints at A and D and by cable ECF that passes through a ring with negligible friction at C and is attached to hooks at E and F. Knowing that the frame supports a uniformly distributed load of 2300 N/m along segment CD, answer the following questions. 245 mm 240 mm E 90 mm B 2300 N/m 80 mm 120 mm. X Y Ring C

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter5: Three-dimensional Equilibrium

Section: Chapter Questions

Problem 5.1P: Bar AB of negligible weight is supported by a ball-and-socket joint at B and two cables attached at...

See similar textbooks

Similar questions

The horizontal link BC is 6.35 mm thick, has a width w = 31.8 mm, and is made of steel with ultimate tensile strength equal to 483 MPa. What should be the factor of safety to be used if the structure shown is designed to support a load P = 44.5 kN.
Before the load is placed on the rigid plate, the top of the central spring is 20 mm lower than the outer springs. Each outer spring is made of 24 turns of 15-mm diameter wire on a mean radius of 60 mm. The central spring consists of 16 turns of 20 mm dimeter wire on a mean radius of 80 mm. If a load P = 5 kN is now placed on the rigid plate. Disregarding the weight of the plate, use G = 83 GPa and use Light spring formula. Determine the maximum shearing stress of the in uter spring. In MPa
Rigid bar ABC is supported by pin-connected bar (1). Bar (1) is 2.0-in. wide, 1.00-in. thick, and made of aluminum that has anelastic modulus of E = 12,000 ksi. Determine the maximum magnitude of load P that can be applied to the rigid bar withoutcausing member (1) to buckle
Static Problem. Indications:The system shown is composed of an ABG bar, supported by a pin at point A and by a collarsmooth at point B (the collar slides on the bar ABG). The collar is pinned to the BDE bar, and theRod BDE is supported by a pin at D and a cable at end E.Based on the above, determine:a) The load P, such that the cable force EF is T.b) The internal loads in a section passing through point G (normal and shear force, and momentflexing).c) Draw bar BDE horizontally and generate the shear force and moment diagramsflexing Indicate the maximum values of shear force and bending moment and their location.?= 22 lb ? = 7 in ? = 6 in
For the dam shown, determine the factor of safety against sliding and overturning. Use unit weight of concrete = 24 kN/m3 and coefficient of friction = 0.80. Show a complete solution
An aluminum strut 2.50m long has a rectangular section 60mm by 30mm. A bolt through each end secures the strut so that it acts as a hinged column about an axis perpendicular to the 60 mm dimension and as a fixed ended column about an axis perpendicular to the 30mm dimension. Determine the safe central load using a factor of safety of 2.5 and E = 70 Gpa.
The column shown below, made from medium carbon steel AISI 1040 (E = 207 GPa and Sy = 290 MPa), has an outer diameter of 50 mm and a wall thickness of 5 mm. If the pipe is held in place by a guy wire, determine the largest horizontal force P that can be applied without causing the pipe to buckle. Use the following correlations if needed,
As shown below, the hydraulic cylinder at C is used to pull a bar from a pump, which is connected to a support ABC at A. The critical elements are the diameter dr of the bar and the diameter dp of the pin at B. For a factor of safety FS = 3.0, determine the required diameters if the maximum load on the bar suction for Pa = 15 kN. The failure voltages of the bar and pin are σe = 340 MPa and τe = 400 MPa, respectively.
The load is supported by the four stainless steels wires that are connected to the rigid members AB and DC. The members were originally horizontal, and each wire has a cross-sectional area of 16mm2. Given that E= 200Gpa for all the steel wires. a) Draw Freee Body Diagram(FBD) of each rigid member. b) Determine the angle of tilt of each member after the 2250N load is applied
Direct tension indicators are sometimes used instead of torque wrenches to ensure that a bolt has a prescribed tension when used for connections. If a nut on the bolt is tightened so that the six 3-mm high heads of the indicator are strained 0.1 mm>mm, and leave a contact area on each head of 1.5 mm2, determine the tension in the bolt shank. The material has the stress-straindiagram is shown.
A square foundation of 1.5 m per side is founded on a soil with a friction angle of ϕ'=28°, c' =20 kN/m2, specific weight of the soil of 17 N/m3 and the specific weight of the saturated soil. of 18.5 kN/m3. Determine the allowable bearing capacity on the foundation with a factor of safety (FS) of 3. Assume that the depth of the water table is 1.2 m and the depth of the foundation is 2.1 m and that a local soil shear failure occurs. . Solve using the theory of Terzaghi and Meyerhof, compare the results.
The eyelet (figure) is used to support a load of 3000 kgf. Determine its diameter d, and the required thickness h, so that the washer does not penetrate or shear the support. Knowing that the eyelet and washer must be made of 1020 steel, cold rolled, with a safety factor of 2.5, and the gap between the screw and the through hole must be 4mm, the steel used will be annealed and threadmachined, and the outer diameter of the washer will be 40mm.